Page 1
The information in this document contains privileged and confidential information. It is intended only for the use of those authorized by Akai Professional. If you are not the authorized, intended recipient, you are hereby notified that any review, dissemination, distribution or duplication of this document is strictly prohibited.
Page 2
As the owner of the copyright to the Manual, Akai does not give you the right to copy the Manual, and you agree not to copy the Manual without the written authorization of Akai. Akai has no obligation to provide to you any correction of, or supplement to, the Manual, or any new or superseding version thereof.
Page 3
ALL REPAIRS DONE BY ANY ENTITY OTHER THAN AN AUTHORIZED AKAI SERVICE CENTER SHALL BE SOLELY THE RESPONSIBILITY OF THAT ENTITY, AND AKAI SHALL HAVE NO LIABILITY TO THAT ENTITY OR TO ANY OTHER PARTY FOR ANY REPAIRS BY THAT ENTITY.
The product is exposed to water or excessive moisture, c. The AC power supply plug or cord is damaged, d. The product shows an inappropriate change in performance or does not operate normally, or e. The enclosure of the product has been damaged. Confidential Akai Service Manual...
Page 10
AD05 Schematics (Main PCB) Confidential Akai Service Manual...
Page 11
2-MainBoard_Part_MCU 2-MainBoard_Part_MCU.Sch 3-MainBoard_Part_Analog 3-MainBoard_Part_Analog.Sch 4-MainBoard_Part_Power 4-MainBoard_Part_Power.Sch 5-MainBoard_Part_Driver 5-MainBoard_Part_Driver.Sch Title M a i n B o a r d Size Number Revision Date: 2011-7-23 Sheet of File: C:\Documents and Settings\..\1-MainBoard.Sch Drawn By:...
Page 12
History: V1.00_20110721 : 1. It is redrawed according to AD05MN300N.pdf & AD05TP300B.pdf. 2. It is improved preliminarily. V1.01_20110722 : 1. Three Resistors R30, R31, R32 should be all 10K . 2. USB Disconnect Transistor Circuit. This circuit is designed to be used in an Open Drain Mode. Please check the resistor input configuration.
Page 13
History: V1.00_20110721 : 1. It is redrawed according to AD05MN300N.pdf & 3.40K 1% AD05TP300B.pdf. AOUTL- 2. It is improved preliminarily. 2.43K 1% 1.43K 1% 270pF V1.01_20110722 : 1. R46 & R56 need to be 33 ohm. 620pF 160nH U41A 2. NOTE: Audio circuitry needs to be placed VERY CLOSE to the output connectors to help with our TDMA requirements.
Page 14
CM must source 3A rated DC barrel jack and DPDT switch that is rated for at least 1.5A per contact NJM2387 +5VA +6VIN +5VA SW70 +5VA +5VA -5VA -5VA MBRA340T3 JP70 -5VA OUT(TAB) TPS60403 ON/OFF VADJ 3.01K 1% 220uF/16V KD-014A-L(DC Power Jack) 220uF/16V GND1 1.00K 1%...
Page 15
History: V1.00_20110721 : D i s a b l e L E D s o u t p u t w h e n p o w e r u p a n d S T M 3 2 r e s e t . 1.
Page 16
History: V1.00_20110721 : 1. It is redrawed according to AD05MN300N.pdf & AD05TP300B.pdf. 2. It is improved preliminarily. PAD1 LED30 YELLOW PAD2 LED31 YELLOW LED32 PAD3 YELLOW PAD1 DumpPAD PAD2 DumpPAD PAD3 DumpPAD PAD4 LED33 9 Dump PADs & LEDs JP30 YELLOW LED_PAD1 PAD5...
Page 17
History: V1.00_20110721 : 1. It is redrawed according to AD05MN300N.pdf & AD05TP300B.pdf. 2. It is improved preliminarily. SYNTH1 SYNTH2 SYNTH3 TEMPO SONG PREV SONG NEXT SEQ PREV SEQ NEXT D110 D113 D115 D117 D119 D121 D123 D125 SW110 1N4148 SW113 1N4148 SW115 1N4148...
Page 18
R150 JP150 330R VR150 10KB LED150 To PannelBoard Title 8 - K n o b B o a r d Size Number Revision Date: 2011-7-23 Sheet of File: C:\Documents and Settings\..\8-KnobBoard.Sch Drawn By:...
Page 19
History: V1.00_20110721 : 1. It is redrawed according to AD05MN300N.pdf & AD05DK100A.pdf. 2. It is improved preliminarily. V1.02_20110723 : 1. Change the connector of JP201 from 3pin to 12pin, and delect JP202. 2. Use UART interface instead of USB to communicated with STM32. 3.
Need help?
Do you have a question about the SynthStation49 and is the answer not in the manual?
Questions and answers