Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for LILYGO T3 V1.6.1
Summary of Contents for LILYGO T3 V1.6.1
- Page 1 T3 V1.6.1 User Guide Version 1.0 Copyright © 2022...
- Page 2 About This Guide This document is intended to help users set up the basic software development environment for developing applications using hardware based on the T3 V1.6.1 Through a simple example, this document illustrates how to use Arduino, including the menu based configuration wizard, compiling the Arduino and firmware download to the...
- Page 3 T3 V1.6.1 Board PINMAP...
- Page 4 Main Chip ESP32 Pin Layout...
-
Page 5: Table Of Contents
Table of Contents 1. Introduction ..........................1.1. T3 V1.6.1 ..........................1 1.2. Arduino ............................. 1.3. Preparation ..........................2. Get Started ..........................2.1. Download the Arduino Software ....................2 2.1.1. Install Prerequisites .......................2 2.1.2. Toolchain Setup ......................2 2.2. Install the Arduino Software ......................3 2.3. -
Page 6: Introduction
(IoT) applications, with Wi-Fi, Bluetooth, flexible power management and other advanced system features. The T3 V1.6.1 manufacturer is Shenzhen Xin Yuan Electronic Technology Co., Ltd. 1.2. Arduino A set of cross-platform applications written in Java. The Arduino Software IDE is derived from the Processing programming language and the integrated development environment of the Wiring program. -
Page 7: Get Started
2. Get Started Get Started 2.1. Download the Arduino Software The quickest how to install the Arduino Software (IDE) on Windows machines 2.1.1. Quick Start Guide The website provides a quick start tutorial Windows: • https://www.arduino.cc/en/Guide/Windows Linux: • https://www.arduino.cc/en/Guide/Linux Mac OS X: •... -
Page 8: Install The Arduino Software
2. Get Started 2.2. Install the Arduino Software Wait for installation 3/13 Xinyuan 2022.07... -
Page 9: Configure
3. Start a Project Configure 3.1. Download Git Download the installation package Git.exe 3.2. Pre-build configuration Click Arduino icon, then right click and select ``Open folder where `` Select hardware -> Mouse ** Right click ** -> Click Git Bash Here 3.3. -
Page 10: Connect
4. Connect Connect You are almost there. To be able to proceed further, connect ESP32 board to PC, check under what serial port the board is visible and verify if serial communication works. 5/13 Xinyuan 2022.07... -
Page 11: Test Demo
4. Configure Test Demo Select File>>Example>>WiFi>>WiFiScan 6/13 Xinyuan 2022.07... -
Page 12: Upload Sketch
5. Build and Flash Upload Sketch 6.1. Select Board Tools<<Board<<ESP32 Dev Module 6.2. Upload Sketch << Upload 7/13 Xinyuan 2022.07... -
Page 13: Monitor
5. Build and Flash 6.2. Serial Monitor Tools << Serial Monitor 8/13 Xinyuan 2022.07... -
Page 14: Ssc Command Reference
6. SSC Command Reference SSC Command Reference Here lists some common Wi-Fi commands for you to test the module. 7.1. op Description op commands are used to set and query the Wi-Fi mode of the system. Example op -Q op -S -o wmode Parameter Table 6-1. -
Page 15: Mac
6. SSC Command Reference Parameter Description -s ssid Scan or connect Access Points with the ssid. -b bssid Scan the Access Points with the bssid. -n channel Scan the channel. Show scan results with hidden ssid Access Points. Show STA connect stutus. Disconnected with current Access Points. -
Page 16: Dhcp
6. SSC Command Reference Parameter Table 6-4. mac Command Parameter Parameter Description Show MAC address. • mode = 1: MAC address in STA mode. -o mode • mode = 2: MAC address in AP mode. 7.5. dhcp Description dhcp commands are used to enable or disable dhcp server/client. Example dchp -S [-o mode] dhcp -E [-o mode]... -
Page 17: Reboot
6. SSC Command Reference Parameter Table 6-6. ip Command Parameter Parameter Description Show IP address. • mode = 1 : IP address of interface STA. • -o mode mode = 2 : IP address of interface AP. • mode = 3 : both Set IP address. - Page 18 FCC Caution: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Need help?
Do you have a question about the T3 V1.6.1 and is the answer not in the manual?
Questions and answers