DMI DARTS CPSIA 2 Series Installation Instructions Manual

Light-up dartboard cabinet

Advertisement

1. Read this manual carefully before starting assembly. Read each step completely before beginning each step.
2. Check inside all parts and cartons before assembling or ordering parts.
3. To make assembly as easy as possible, place all parts in a cleared area and remove the packaging material. Organize all
parts as per parts identifier in the assembly manual. Do not dispose of the packing material until assembly is completed.
4. Avoid scratching dartboard cabinet parts during the assembly process.
5. Assemble product on clean, level and flat surface.
6. Take time to correctly orientate parts exactly as per each assembly diagram.
7. Save this instruction in the event that the manufacturer has to be contacted for replacement parts.
Thank you for buying our product. We try hard to ensure that our products are of high quality and free of problems, such as Manufacturing
defects or missing parts. However, if you have any problems with your new product, please DO NOT RETURN IT TO THE STORE!
Please Do Not Return This Product To The Store!
Contact Escalade Sports customer service department at:
Phone:
1-800-467-1421
E-mail:
customerservice@escaladesports.com
Please provide model number and/or part number of the product and/or part when you call or write. These numbers can be found on the
product, packaging, and/or in this Owner's Manual.
Please visit our website at: www.escaladesports.com
ON-LINE TROUBLE SHOOTING
FREQUENTLY ASKED QUESTIONS
First Time Battery Installation:
Locate battery compartment for this product.
Use alkaline batteries for maximum performance.
Using a small Phillips head screwdriver – loosen and remove the battery compartment cover screw(s).
Remove battery compartment cover.
Install new batteries only after reading the " Battery Information NOTICE" !
Replace compartment cover and secure cover with the cover screw. Do not over tighten and strip out the screw.
IMPORTANT: BATTERY INFORMATION
Please retain this information for future reference. Batteries must be installed / replaced by an adult .
Notice:
1. Remove and replace batteries when the electrical features of this product work slowly or are not functional.
2. Do not mix old and new batteries.
3. Do not mix different types of batteries : Alkaline , Standard ( Carbon-Zinc) , or rechargeable (Nickel-Cadmium batteries).
4. Use Alkaline Batteries for maximum performance.
5. Do not use damaged batteries.
6. Use only batteries of the same or equivalent type as recommended.
7. Install new batteries as per matching the battery polarity guide (+ & - , positive and negative) inside of the battery
compartment. Correct battery polarity installation is critical as to not damage the internal electrical components as well
as insuring the correct functionality of the product.
8. Do not short circuit the battery terminals.
9. Always remove exhausted, leaking, weak, and batteries from long periods of nonuse from the product. Battery leakage
and corrosion can cause damage.
10. Check the battery terminals are clean and bright before installing new batteries.
11. Dispose of old batteries safely and per local battery disposal codes.
12. Do not dispose of batteries into a fire as they may explode or leak.
13. If removable rechargeable batteries are used , they are to be charged under adult supervision.
14. Rechargeable batteries are to removed from the product before they are charged.
15. If you use a battery charger, it should be examined regularly for damage to the cord, plug, enclosure, and other parts.
Do not use a damaged or malfunctioning charger until it is properly repaired.
16. Non rechargeable batteries must not be recharged.
17. Always remove batteries from this product for extended storage and or non-use.
18. Should this product cause , or be affected by, local electrical interference, move it away from other electrical equipment.
Reset (switching off and back on again and or removing and reinserting the batteries) if necessary.
O W N E R ' S
CAUTION:
Toll-Free!
ON-LINE PARTS REQUESTS
ADDITIONAL ESCALADE SPORTS PRODUCT INFORMATION
Light-UP Dartboard Cabinet
Installation Instruction Manual
CPSIA#2-
M A N U A L
READ ASSEMBLY, OPERATING AND
SAFETY INSTRUCTIONS CAREFULLY!
Mailing Address (correspondence only):
Escalade Sports
817 Maxwell Ave., Evansville, IN 47711
-
TECHNICAL ASSISTANCE
-VS

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CPSIA 2 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for DMI DARTS CPSIA 2 Series

  • Page 1 Light-UP Dartboard Cabinet Installation Instruction Manual CPSIA#2- O W N E R ’ S M A N U A L 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step. 2. Check inside all parts and cartons before assembling or ordering parts. 3.
  • Page 2 PARTS IDENTIFIER H2 (to scale) H3 (to scale) H4 (to scale) 3.5x10 mm Mounting Bracket 4 mm Flat Washer 3 mm Nut Phillips Head Screw 1 pc 2 pcs 2 pcs 2 pcs H5 (to scale) H6 (to scale) H8 (to scale) 5 x 20 mm 4x50 mm 1.5x20 mm...
  • Page 3 TOP BOARD WITH LED UNIT INSTALLATION GUIDE Install H12 Wooden Dowel Pins into Locate the pilot holes on the top of the Step.1 Step.2 P2 Top Board & top cabinet frame. LED light board and the top of the cabinet. Attach the 2 pcs H14 Connecting Brackets using H13 Screws.
  • Page 4: Install Mounting Bracket

    INSTALL THE DARTBOARD MOUNTING BRACKET INTO CABINET Step.1 Install Mounting Bracket 1. Align 2 holes on the H1 Mounting Bracket with the 2 backboard center holes. 2. Using 2 pcs H2 Screw and H3 Washer, insert from the cabinet backside and go through the 2 backboard center holes. 3.
  • Page 5: Tools Required

    Tools required: ● Stud Finder ● Tape Measure . ● Small & Medium Phillips driver – Electric OK --- Low torque as to not strip out any screws . ● Carpenters Level ● Awl and or Pencil ● Drill and 1/16” Drill Bit ●...
  • Page 6 11. Now, install H8 screws into each drilled pilot hole leaving approx. 1/2” of the screw head exposed from the wall as per Figure 2.2. (This will allow you to “Hang” the Dart Cabinet onto these two screws). 12. Carefully hang the dart cabinet onto these two hanging screws. Make sure the cabinet gently drops down into the “keyhole slots”...
  • Page 7 Step.3 Install Dartboard into Cabinet 1. Install H5 Mounting Screw to the pilot hole which is marked with black marker on the back center of the dartboard and leave approx. 1/8” of the screw head exposed from the backboard per shown on Figure 3.1. (This will allow you to “Hang”...
  • Page 8: Limited Warranty

    LIMITED WARRANTY Escalade Sports (the Company) warrants the Product to be free from defects in workmanship and materials under normal use and conditions FOR A PERIOD OF 90 DAYS FROM THE DATE OF ORIGINAL PURCHASE in the United States and Canada. What Is Covered Except as provided below, this Limited Warranty covers all defects in materials and workmanship.

This manual is also suitable for:

D4400

Table of Contents