Integra DTR-5 Instruction Manual
  1. Manuals
  2. Brands
  3. Integra Manuals
  4. Receiver
  5. DTR-5
  6. Instruction manual
Integra DTR-5 Instruction Manual

Integra DTR-5 Instruction Manual

Audio video control receiver
Hide thumbs
Table of Contents

Advertisement

Quick Links

Audio Video Control Receiver
DTR-5
Instruction Manual
DIMMER
STANDBY/ON
STANDBY
POWER
ON
OFF
A
SPEAKERS
B
DISPLAY
STEREO
/DTS SURROUND
PHONES
MULTI CH
DVD
VIDEO 1
VIDEO 2
INPUT
Thank you for purchasing the Integra Audio Video
Control Receiver.
Please read this manual thoroughly before making
connections and turning on the power.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new Audio Video Control
Receiver.
Please retain this manual for future reference.
FM MUTE /
DIGITAL/
SP / SYS
MASTER VOLUME
MEMORY
MODE
DOWN
TUNING
UP
ANALOG
SETUP
CH LEVEL
MODE
PRESET / MODE ADJ
DOW N
UP
ENTER / SCAN
LISTENING MODE
LATE NIGHT /
LFE LEVEL
5 CH STEREO
DSP
FRONT EFFECT
Re -EQ
CONTROL
BASS
VIDEO 3
TAPE
FM
AM
PHONO
C D
TREBLE
Contents
Before using
Important Safeguards........................ 2
Precautions ....................................... 3
Features............................................. 4
Supplied accessories......................... 4
Before operating this unit ................. 5
Preparation
Connecting other devices ................. 8
Connecting speakers....................... 10
Positioning speakers ....................... 11
Connecting the power..................... 11
Operation
Speaker setup.................................. 14
Selecting a sound source ................ 17
Using Listening Mode .................... 21
Tuning in a radio station................. 24
Recording a source ......................... 27
in the Sub-room ........................... 29
RC-391M ..................................... 34
Using a Macro function .................. 36
Appendix
Troubleshooting guide.................... 40
Specifications ................................. 41
Control guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DTR-5 and is the answer not in the manual?

Questions and answers

Related Manuals for Integra DTR-5

Summary of Contents for Integra DTR-5

  • Page 1: Table Of Contents

    VIDEO 1 VIDEO 2 VIDEO 3 TAPE INPUT Thank you for purchasing the Integra Audio Video Control Receiver. Please read this manual thoroughly before making connections and turning on the power. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new Audio Video Control Receiver.

  • Page 2: Important Safeguards

    19. Outdoor Antenna Grounding – If an outside antenna is con- S3125A nected to the receiver, be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges. Article 810 of the National Electrical...

  • Page 3: Precautions

    Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

  • Page 4: Features

    Features ®*1 ®*2 , Dolby Digital and Dolby Decoders 5.1 Channel Direct Inputs Cinema Re-EQ™ Circuitry High Definition DSP 8 DSP Listening Modes Full Bandwidth Power to 5 Main Channels Wide Range Amplifier Technology (WRAT) High-Current, Low-Impedance 6-Ohm Drive Discrete Output Stage Circuitry for 5 Main Channels Massive Isolated Transformer High-Quality Aluminum-Extruded Heat Sinks Audiophile-Grade “Fine Gold”...

  • Page 5: Before Operating This Unit

    Using the remote controller Point the remote controller toward the remote control sensor. The STANDBY indicator lights up when the unit receives a signal DTR-5 from the remote controller. Notes Place the unit away from strong light such as direct sunlight or inverted fluorescent light which can prevent proper operation of the...

  • Page 6: Audio Equipment Connections

    Turntable A DVD or other component equipped with a digital output can be connected to this receiver. The digital connection must be used in conjunction with an analog connection, because if the analog cable is disconnected, the audio output from TAPE OUT (REC) and VIDEO 1 OUT will not work.

  • Page 7: Video Equipment Connections

    This receiver can be used with only a monitor TV equipped with a video input jack. Interference may be caused between the TV and this receiver. If this interference occurs, place the receiver and the TV as far apart as possible. We do not recommend the use of a common TV/FM antenna (see antenna section).

  • Page 8: Connecting Other Devices

    DIGITAL INPUT COAXIAL 2 COAXIAL 1 AC I NLET FRONT SPEAKERS OPTICAL SURROUND REMOTE CONTROL SPEAKERS AC 120V 60Hz SWITCHED TOTAL 120W 1A MAX. AV RECEIVER DTR-5 MODEL NO. RATING: AC120V 60Hz 3.9A 2-1, NISSHIN-CHO, NEYAGAWA-SHI,OSAKA, JAPAN MANUFACTURED IN MALAYSIA...
  • Page 9 Note: Do not use any power cable other than the included cable. The included cable is designed for use only with the DTR-5. Do not use it for any other device. Do not connect or disconnect the outlet plug from the DTR-5 while the other end is plugged into the wall AC outlet.

  • Page 10: Connecting Speakers

    Use FRONT SPEAKERS B terminals to connect a second pair of front speakers. This receiver is designed to produce optimum sound quality when speakers with impedances within the specified ranges are con- nected. Please check the following information and choose speakers with appropriate impedances for the connections.

  • Page 11: Positioning Speakers

    1. Press the MODE AUDIO button. 2. Press the POWER ON button to turn on the power to the DTR-5, or press the POWER STNBY button to set the receiver in standby mode. You cannot use the remote controller if the POWER switch on the receiver is set to OFF.

  • Page 12: Making Antenna Connections

    Making antenna connections Slit C To DTR-5 Insert into the hole. Outdoor Indoor Connecting the 300 ohm ribbon wire: antenna antenna Loosen the screws and wrap the wire around these screws. Then tighten the screws with a screwdriver. 300 ohms...
  • Page 13 Making antenna connections ANTENNA Remove the insulation at the tip of the cable, and insert the cable securely, fully to the end of the exposed tip. ANTENNA ANTENNA ANTENNA Connecting the included antennas Connecting the FM indoor antenna: The FM indoor antenna is for indoor use only. Extend the antenna and move it in various directions until the clearest signal is received.

  • Page 14: Speaker Setup

    Speaker setup Follow the steps below before you start operating the unit. SP / SYS SETUP ENTER / SCAN ENTER / SCAN PRESET / MODE ADJ DOW N PRESET / MODE ADJ DOW N DIMMER POWER DISPLAY Set whether a speaker is used or not, and set the size of the con- nected speakers.
  • Page 15 Speaker setup PRESET / MODE ADJ DOW N PRESET / MODE ADJ DOW N SP / SYS SETUP ENTER / SCAN SP / SYS SETUP ENTER / SCAN meter PRESET / MODE ADJ DOW N PRESET / MODE ADJ DOW N PRESET / MODE ADJ DOW N 4.
  • Page 16 Speaker setup 3. CH SEL button Using the Test Tone function on the main unit 1. Press the SP/SYS SETUP button. 2. Press the ENTER/SCAN button while “SPEAKER SETUP” appears on the display. 3. Press the SP/SYS SETUP button twice while “CONFIG SETUP” appears on the display. 4.

  • Page 17: Selecting A Sound Source

    3. INPUT SELECTOR button Use this button to select a desired sound source. (V4 button is not used for this DTR-5.) 4. Select a Listening mode. (Refer to page 21) These controls allow you to adjust the volume of the Front, Center, Surround speakers and subwoofer simultaneously.
  • Page 18 PRESET / MODE ADJ DOW N ENTER / SCAN Audio (digital or analog) selection DTR-5 DIGITAL INPUT You can select either digital audio or analog audio for DVD, CD, VIDEO 1, VIDEO 2, VIDEO 3, or TAPE input. The default setting COAXIAL 2 is ANALOG.
  • Page 19 Selecting a sound source LEFT CENTER SUBWOOFER L-SURROUND When Multi channel input is selected as a source Follow the steps below to adjust the level of each speaker if you have selected MULTI CH INPUT. 1. Press MODE AUDIO button on the remote controller. 2.
  • Page 20 Temporary muting (MUTING) (Remote controller only) Press the MUTING button. The “MUTING” appears on the display and the sound from the speakers or headphones will be switched off by the receiver’s audio muting circuits. To cancel, press the MUTING button again, or...

  • Page 21: Using Listening Mode

    DTS source, a short noise may be heard. This is not a mal- function. 4. The DTS indicator on the DTR-5 lights up while it plays the DTS mark. source. When playback concludes and the DTS signal transmis- sion stops, the DTR-5 remains in DTS mode and the DTS indica- tor remains lit.
  • Page 22 Using Listening Mode 3. Use these buttons to set the Listening mode parameters. (Refer to page 23). 2. LISTENING MODE buttons These button allow you to select a listening mode. VOL button (qup/udown) Use this button to adjust the volume level. CH SEL/LEVEL+/–...
  • Page 23 To play a Dolby digital or DTS Surround source, you need to connect the sound source using the digital input connector. When you play the Dolby Digital or DTS Surround source, the DTR-5 automatically enters Dolby Digital Surround (stereo) or DTS Surround (stereo) mode respectively. DTS Surround Dolby Pro Logic —...

  • Page 24: Tuning In A Radio Station

    Tuning in a radio station DOWN TUNING FM MUTE / MODE DISPLAY FM MUTE/MODE TUNING DOWN/UP FM MUTE / DIGITAL/ SP / SYS DIMMER MODE ANALOG SETUP CH LEVEL MEMORY DOWN TUNING MODE STANDBY/ON PRESET / MODE ADJ DOW N STANDBY POWER ENTER / SCAN...

  • Page 25: Using Preset Radio Stations

    Using preset radio stations FM MUTE/MODE MEMORY DIMMER MEMORY STANDBY/ON STANDBY POWER SPEAKERS LISTENING MODE DISPLAY STEREO /DTS SURROUND PHONES MULTI CH VIDEO 1 VIDEO 2 VIDEO 3 INPUT MEMORY ENTER / SCAN PRESET / MODE ADJ DOW N ENTER / SCAN TUNING DOWN/UP PRESET/MODE ADJ MODE AUDIO...
  • Page 26 Using preset radio stations PRESET / MODE ADJ DOW N MEMORY ENTER / SCAN Selecting a preset station 1, 2 Remote controller 1. Select the tuner as the source by pressing the AM or FM 2. Enter the desired preset number using the PRESET/MODE Remote controller operation Remote controller 1.

  • Page 27: Recording A Source

    (VIDEO 1) (VIDEO 2, VIDEO 3) VIDEO 2 VIDEO 3 Recording an audio source Make all connections between the tape deck and the receiver as MASTER VOLUME DIGITAL/ SP / SYS shown in the “Audio equipment connections” diagram (page 6).
  • Page 28 Recording a source DIMMER STANDBY/ON STANDBY POWER SPEAKERS DISPLAY STEREO /DTS SURROUND PHONES MULTI CH VIDEO 1 VIDEO 2 INPUT 1·5 VDP, VCR, DVD (VIDEO 2, VIDEO 3) 2·5 VCR (VIDEO 1) VIDEO 2 TAPE MASTER VOLUME FM MUTE / DIGITAL/ SP / SYS MEMORY...

  • Page 29: Enjoying Music And Movies In The Sub-Room

    If you connect Onkyo Multi-room Remote System components as shown in the figure below, you can control the components from an adja- cent sub-room as well as from the room where the DTR-5 is located. The following equipment (sold separately) is essential for using the Onkyo Multi-Room System: Onkyo’s Multi-Room System kits HKT-600 or HKT-700 (IR Remote Controller Extension System), or...
  • Page 30 Outline of Multi-room Remote System If you connect Onkyo Multi-room Remote System components as shown below, you can control the components from an adjacent sub- room as well as from the room where the DTR-5 is located. Speaker A (Main room)

  • Page 31: Using The Remote Controller

    When you use a remote controller, typically you press one of the MODE buttons that corresponds to the device you wish to control, then press the operation buttons. For example, if you wish to control the DTR-5 from a remote controller, first press the MODE AUDIO button, then press an appropriate operation button.
  • Page 32 : Rewind : Fast forward : Pause : Eject : Numeric keys : Adjusting the volume level of the DTR-5 : Muting the sound from the DTR-5 : Turning the power on and off to the DVD player : DVD setup...
  • Page 33 : Rewind : Fast forward : Record : Pause : Eject : Numeric keys : Confirm : Adjusting the volume level of the DTR-5 : Muting the sound from the DTR-5 connec- : Playback : Stop : Rewind : Fast forward...

  • Page 34: Programming The Remote Controller Codes Of Other Devices Into The Rc-391M

    RC-391M. You may pro- gram other remote controller codes into these buttons. If you wish to restore the Onkyo/Integra preset codes after you pro- gram new codes, erase the new codes. (See page 35.)
  • Page 35 Programming the remote controller codes of other devices into the RC-391M See page 39 for information on how to erase the learned codes from all buttons. SEND/LEARN indicator SEND/LEARN indicator Erasing a learned code You can erase a learned code. You cannot erase preset codes. Erasing a code programmed in a button 1.

  • Page 36: Using A Macro Function

    A Macro function enables you to program a series of button operations on the remote controller into a single button. For example, you need to follow the steps below to play a CD player connected to the DTR-5 without using the Macro function: 1: Press the MODE AUDIO button.
  • Page 37 The SEND/LEARN indicator flashes twice slowly. 4. Check to see if the button has been programmed correctly. Point the RC-391M toward the DTR-5 and press the MACRO DIRECT button, and make sure that the device responds as pro- grammed.
  • Page 38 Using a Macro function 1, 2 Erasing a learned remote controller button oper- ation from the MACRO MODE buttons 1. Press and hold down the corresponding MODE button and press the MACRO MODE button, then release the buttons. When you press the MODE button, the SEND/LEARN indica- tor lights up.
  • Page 39 Using a Macro function Erasing all codes and operations programmed in the buttons This procedure will erase all remote controller codes for the other devices and all macro operations that have been programmed in the RC-391M (see pages 34, 36 and 37). 1.

  • Page 40: Troubleshooting Guide

    Plug in the power cable into the AC outlet securely. Make sure that the power cable is not disconnected from the DTR-5. Turn the power button off and then on again or remove the AC plug from the outlet and then plug it again.

  • Page 41: Specifications

    Specifications AMPLIFIER SECTION Continuous Average Power output (FTC) All channels: 70 watts per channel min. RMS at 8 ohms, 2 channels driven from 20 Hz to 20 kHz with no more than 0.08% total harmonic distortion. 90 watts min. RMS at 6 ohms, 2 chan- nels driven from 1 kHz with no more than 0.1% total harmonic distortion.

  • Page 42: Control Positions And Names

    Control positions and names STANDBY/ON STANDBY POWER SPEAKERS PHONES Display Front panel For more information about buttons or knobs, refer to the pages listed in the brackets ( [ ] ) below. 1. STANDBY indicator [5, 11] 2. STANDBY/ON button[9, 11] 3.
  • Page 43 DTR-5.] 10. TRACK button [32] 11. CD/TAPE/DVD/MD operation buttons [31~33] 12. Input Selector buttons [17] The V4 button is not used for the DTR-5. 13. Numeric key/STEREO/DSP A, B/CH SEL/LEVEL+,–/DIMMER buttons [31~33] [The DIRECT button and THX* button are not used for the DTR-5.]...
  • Page 44 Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 0720-31-8111 Fax: 0720-33-5222 ONKYO U.S.A. CORPORATION 200 Williams Drive, Ramesy, N.J. 07446, U.S.A. Tel: 201-825-7950 Fax: 201-825-8150 E-mail: onkyo@onkyousa.com ONKYO EUROPE ELECTRONICS GmbH Industriestrasse 20, 82110 Germering, GERMANY Tel: 089 84 93 20 Fax: 089 84 93 226 E-mail: info@onkyo.de ONKYO CHINA LIMITED Units 2102-7, Metroplaza Tower I, 223 Hing Fong Road, Kwai Chung,...

Table of Contents

Save PDF