Related Manuals for HEXFLY PRO-X2
Summary of Contents for HEXFLY PRO-X2
- Page 1 MAN-PRO-X2-2022-01-03 2 CHANNEL BALANCE CHARGER Li-ion/LiPo/LiHV/LiFe/NiMH/NiCd/Pb AC 100V-240V / DC 11.0V-18.0V...
- Page 2 Thank you for purchasing the HEXFLY PRO-X2 Charger. This charger is comprised of two, multi-chemistry capable, rapid chargers/dischargers and cell balancers with built in microprocessors built into one component. Please read and understand the entire manual before operating this charger.
- Page 3 WWW.HEXFLY.COM...
- Page 4 Dual Charge Circuitry This charger features two individual charging circuits allowing you to charge 2 batteries simultaneously, regardless of battery chemistry or cell count. High Power Charging Circuit This charger features a powerful 80-Watt charging circuit. The charger can safely charge or discharge up to 15 cells of NiMH or NiCd batteries and up to 6S LiPo batteries.
- Page 5 Multiple Charging Leads Included The HEXFLY PRO-X2 charger comes with the following charge leads, providing the user with the most common connection types. JST Plug (1) Alligator Clip (1) XT60 Plug (2) Receiver Plug (1) Tamiya Plug (1) T-Plug (1)
-
Page 6: Exterior Of The Unit
2. EXTERIOR OF THE UNIT... - Page 7 To avoid short-circuits between the charge leads, always connect the charge cable to the unit • first, and only then to the battery to be charged or discharged. Reverse the sequence when disconnecting. Do not attempt to disassemble battery packs. • Li-ion WWW.HEXFLY.COM...
- Page 8 The typical purpose of discharge is to determine the residual capacity of the battery, or to lower the voltage of the battery to a defined level. Much like the process of charging, when you discharge batteries you must not leave the battery unattended. To avoid the battery becoming over discharged, set the final discharge voltage correctly.
- Page 9 WWW.HEXFLY.COM...
- Page 10 DETECTION. A ten minute delay is suggested for larger mAh packs, but small capacity batteries may finish charging/discharging before the 10 minute mark which could result in catastrophic failure of the battery. If there are any doubts on how to use this feature, please go to WWW.HEXFLY.COM...
- Page 11 WWW.HEXFLY.COM...
- Page 12 In the case of the example, LiPo. The value underneath the chemistry type is the charge current. Check your batteries specifications for proper charge rating, but with all HEXFLY batteries, we recommend a 1C charge rate. If your battery is a 5000mAh, your charge current should be 5.0A.
- Page 13 Use the increase/decrease buttons to change the values and use the START/ENTER button to confirm the values. When the values have been set correctly and you are ready to BALANCE charge, press and hold the START/ENTER button for 3 seconds to begin the process. WWW.HEXFLY.COM...
- Page 14 Like a standard charge sequence, the value in the lower left hand corner of the screen shows the selected charge current and the value in the lower right hand corner of the screen shows the selected voltage of the pack that will be charged. To change these values, press the START/ENTER key to cycle through the adjustable settings.
- Page 15 If the battery you’re trying to charge isn’t an LiHV battery, press the Stop button to exit the program and select the correct battery type. If the battery you’re trying to charge is confirmed to be an LiHV battery, then continue to the program. WWW.HEXFLY.COM...
- Page 16 Use these programs only when charging a NiMH (Nickel-Metal-Hydride) or NiCd (Nickel-Cadmium) battery. To alter the value on the display, press the START/ENTER key. The charge current can now be altered by using the increase/decrease buttons. The value will be saved by pressing the Start/Enter key once. To start the process, press and hold the START/ENTER button for more than 3 seconds.
- Page 17 When the process is completed, use the increase/decrease buttons to see the amount of capacity that was charged/discharged. By pressing increase/decrease again, the results of the next charge cycle will be shown. WWW.HEXFLY.COM...
-
Page 18: Save Data Program
This feature can store information for up to 5 batteries to be called back for the process of charging or discharging without having to reprogram the charger. To alter the values, press START/ENTER, then change the blinking value using the increase/decrease buttons. hexfly.com 0685... - Page 19 "current" field is blinking. Setting up discharge current and final voltage. Setting up the sequence of charge and discharge as well as the amount of times to cycle. Saving the data. WWW.HEXFLY.COM...
- Page 21 The charger has an internal error. Please contact Redcat customer service. The processor cannot control the input current. Please contact Redcat customer service. WWW.HEXFLY.COM...
- Page 22 Dimensions: HEXFLY warrants this product to be free of material and workmanship defects when new. HEXFLY will at its sole discretion repair or replace defective components free of charge within 90 days from date of purchase or within 30 days for all electronic components.
- Page 23 The information in this manual is distributed on an "As Is" basis, without warranty. While every precaution has been taken in the preparation of the manual, HEXFLY and their affiliates do not have any liability to any person or entity with respect to any loss or damage caused or alleged to be caused directly or indirectly by the information contained in this manual or by the products described in it.
- Page 24 WWW.HEXFL Y.COM...
Need help?
Do you have a question about the PRO-X2 and is the answer not in the manual?
Questions and answers