Related Manuals for Infinity Reference RS-8
Summary of Contents for Infinity Reference RS-8
- Page 1 RS-8 Reference Series (RS) Floorstanding Speaker System Model RS-8 Owner’s Manual Part #334428-001 ® Reference Standard (RS 4, RS 5) – Owner’ s Manual 1...
-
Page 2: Table Of Contents
ABLE OF ONTENTS 2 Reference Standard (RS-8) – Owner’ s Manual Caution...3 Important Safety Instructions...4 The Reference Series (RS) ...5 Unpacking the Speakers...5 Installing Feet ...5 Planning Your System ...6 Stereo-Speaker Placement ...6 Home-Theater Placement...6 Wiring the System...7–8 Turn Off All Power...7 Final Adjustments...9... -
Page 3: Caution
DO NOT REMOVE COVER (0R BACK) NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED PERSONNEL THIS INFINITY PRODUCT IS DESIGNED FOR 120-VOLT USE ONLY! FOR DETAILED SAFETY PRECAUTIONS, PLEASE SEE FOLLOWING PAGE IN THIS OWNER'S MANUAL FOR “IMPORTANT SAFETY INSTRUCTIONS.”... -
Page 4: Important Safety Instructions
For products intended to oper- ate from battery power, or other sources, refer to the operating instructions. 4 RS-8 – Owner’ s Manual IMPORTANT SAFETY INSTRUCTIONS 12) Grounding or Polarization – Figure A. -
Page 5: The Reference Series (Rs)
4. Carefully flip each speaker upright to sit on its feet. 5. If needed, adjust the feet so each speaker is level and then tighten each nut with the enclosed wrench. To protect hard surfaces (e.g., wood floors), slip a nylon dome onto each round end. -
Page 6: Planning Your System
TV picture. NOTE: For maximum home-theater enjoyment, your audio system should also include a center- channel speaker and a pair of rear-surround speakers. Contact your local Infinity dealer for recom- mendations on adding these home-theater speakers to your system. -
Page 7: Wiring The System
Speakers and electronics terminals have corresponding (+) and (–) terminals. It is important to connect both speakers identically: (+) on the speaker to (+) on the amplifier and (–) on the speaker to (–) on the amplifier. Wiring “out of phase” results in thin sound, weak bass and a poor stereo image. - Page 8 YSTEM If your receiver has a subwoofer output: The RS-8 incorporates two different types of line-level inputs that allow you to optimize the loudspeakers’ performance in your system. If your receiver/processor’ s subwoofer output is already low-passed filtered, meaning the high frequencies have been removed by the receiver, use the subwoofer input labeled Direct.
-
Page 9: Final Adjustments
NOTE: You should hear balanced audio reproduction across the entire frequency spectrum. If not, check all wiring connections or, for more help, consult the Authorized Infinity Dealer where you purchased the system. -
Page 10: Troubleshooting
• Make sure the connections to the left and right “Speaker Inputs” have the correct polarities (+ and –). • Make sure that the RS-8 is plugged into an active electrical outlet. • Adjust the subwoofer-level control. • Make sure the input-select switch is in the correct position (pages 7, 8). -
Page 11: Specifications
Bass: RIVE NITS Midbass: High Frequency: IMENSIONS Height, Width, Depth: 15 ~ 175W 32 ~ 20,000Hz 92dB spl 100W 8" (203mm) " (165mm) -1/2 1" 40 x 7-1/2 12-1/2" (1016 x 191 x 318mm) RS-8 – Owner’ s Manual 11... - Page 12 Infinity constantly strives to update and improve existing products, as well as create new ones. Therefore, the specifications and construction details in this and related Infinity publications are subject to change without notice. © 1998 Infinity Systems, Inc., 250 Crossways Park Drive, Woodbury, NY 11797 USA (516) 496-3400 •...
Need help?
Do you have a question about the Reference RS-8 and is the answer not in the manual?
Questions and answers