Zurich ZR13s Owner's Manual page 19

When the scan is complete, the Available Systems screen
If you have not yet established an account, you must register for
5. M (Menu) button – When pressed, displays the Main Menu.
displays. The screen shows the number of DTCs recorded for
a FREE RepairSolutions 2 account before proceeding.
6. LD button – When pressed while linked to a vehicle, places the
each available module.
3. Connect the Code Reader to a vehicle and establish a Bluetooth or
Scan Tool in Live Data mode.
2. Select the module for which you wish to view DTCs, then press
WiFi connection with your Smart Device (refer to CONNECTING TO
7. UP button – When in MENU mode, scrolls UP through the
ENTER
BLUETOOTH / WIFI, below). Be sure your Smart Device is
menu options. When LINKED to a vehicle, scrolls UP through the
requested DTCs are retrieved.
connected to an available WiFi network.
current display screen to display any additional data.
If the Scan Tool fails to link to the selected module, a
The RepairSolutions 2 app will store two WiFi configurations
8. ENTER button - When in Menu mode, confirms the selected
"Communication Error" message shows. only.
option or value.
4. Retrieve diagnostic data (refer to CODE RETRIEVAL PROCEDURE - Ensure your vehicle is OBD2 compliant.
9. DOWN button - When in MENU mode, scrolls down through the
on page 6 for details).
- Verify the connection at the DLC, and verify the ignition is ON.
menu options. When LINKED to a vehicle, scrolls down through the
5. The RepairSolutions 2 app automatically displays a report based on
current display screen to display any additional data.
- Turn the ignition OFF, wait 5 seconds, then back ON to reset
the retrieved diagnostic data.
10. GREEN LED - Indicates that all engine systems are running the computer.
If the Code Reader is not connected to WiFi or Bluetooth,
normally (all Monitors on the vehicle are active and performing their
- Press POWER/LINK
vehicle data will not be saved.
diagnostic testing, and no DTCs are present).
Menu
11. YELLOW LED - Indicates there is a possible problem. A "Pending"
If the selected module does not support the "Read DTC" function,
CONNECTING TO BLUETOOTH / WIFI
DTC is present and/or some of the vehicle's emission monitors have
an advisory message displays. Press System Menu
not run their diagnostic testing.
return to the System Menu, or, press M to access the Main
Launch the RepairSolutions 2 app an follow the prompts to
12. RED LED - Indicates there is a problem in one or more of the Menu.
establish Bluetooth and (optionally) WiFi connections, as follows:
vehicle's systems. The red LED is also used to show that DTC(s)
3. Refer to DISPLAY FUNCTIONS on
1. Launch the RepairSolutions 2 app. Select Wifi Tools Settings
are present. DTCs are shown on the Scan Tool's LCD display. In
page 3 for a description of LCD display
from the menu. Power on your Code Reader, then select from the
this case, the Malfunction Indicator ("Check Engine") lamp on the
elements.
list of available devices.
vehicle's instrument panel will light steady on.
2. When Bluetooth pairing is complete, a confirmation screen displays.
13. Display - Displays test results, Scan Tool functions and Monitor status
Click Continue.
information. See DISPLAY FUNCTIONS, below, for details.
14. CABLE - Connects the Scan Tool to the vehicle's Data Link Connector
If a Bluetooth connection cannot be established, an advisory
(DLC).
message displays. Tap Try Again to repeat the pairing process.
3. Follow the on-screen prompts to connect to an available WiFi
DISPLAY FUNCTIONS
network.
2
You can automatically connect to the network your Smart Device
is currently connected to, or you can manually connect to
another available network.
3
Note that only 2.4GHz networks are supported.
4
If no codes are present, the message "No (system name) DTC's are
5
If you do not wish to connect to a WiFi network at this time, tap
presently stored in the vehicle's computer" shows. Press System
SKIP.
Menu
4. When WiFi pairing is complete, a confirmation screen displays. Click
4. If more than one code was retrieved press DTC/FF to display
6
Continue to view the "Setup Complete" message, then click
additional codes one at a time.
Continue to enter RepairSolutions 2.
7
Whenever the Scroll function is used, the Scan Tool's
If a WiFi connection cannot be established, an advisory
communication link with the vehicle's computer disconnects. To
9
message displays. Tap Try Again to repeat the pairing process.
re-establish communication, press POWER/LINK
13
5. When the last retrieved DTC has been displayed and DTC/FF is
pressed, the Scan Tool returns to the first code.
To exit the enhanced mode, Press System Menu
See Figure 2 for the locations of items 1 through 15, below.
to the System Menu. Select Global OBD, then press ENTER
1. I/M MONITOR STATUS field - Identifies the I/M Monitor status area.
to return to the Global OBD2 mode.
For technical questions, please call 1-888-866-5797
. A "One moment please" message displays while the
to return to the System Menu.
If the definition for the
currently displayed code is
not available, an advisory
message shows.
I/M MONITOR STATUS
icons are not displayed
when using the Network Test function.
In the case of long code definitions, a small arrow is
1
shown in the upper/lower right-hand corner of the code
display area to indicate the presence of additional
information.
to return to the System Menu.
Figure 2. Display Functions
About the Scan Tool Using the Scan Tool
Using the Scan Tool
NETWORK TEST
DISPLAY FUNCTIONS
CONNECTING TO BLUETOOTH / WIFI
to continue, or, press System
15 14
NETWORK TEST
to
10
11
12
8
again.
to return
17
3
17 17