FERREX 25CC User Manual

Petrol chainsaw

Hide thumbs

Table of Contents

Quick Links

ALDI guarantees that our exclusive brand products are developed to our

stringent quality specifications. If you are not entirely satisfied with this

product, please return it to the nearest ALDI store within 60 days from the

date of purchase, for a full refund or replacement, or take advantage of our

after sales support by calling the supplier's Customer Service Hotline.

Made in China

FERREX

is a registered trademark of ALDI Stores

DISTRIBUTED BY:

ALDI STORES

1 SARGENTS ROAD

MINCHINBURY NSW 2770

www.aldi.com.au

AFTER SALES SUPPORT

705552

1300 855 831

support@scheppach.com.au

YEAR

MODEL:

WARRANTY

CSP2540

04/2021

User Manual

25CC PETROL CHAINSAW

Contents

Overview ..................................................................................... 3

Package contents/part list ......................................................... 6

Explanation of Symbols .............................................................10

Introduction ...............................................................................12

Layout .........................................................................................13

Scope of delivery ........................................................................14

Intended use ..............................................................................15

Safety regulations ......................................................................16

Set up ......................................................................................... 25

Operation ................................................................................... 29

Operating instructions ...............................................................31

Cleaning .....................................................................................40

Maintenance and servicing .......................................................41

Technical data ........................................................................... 49

Storage ...................................................................................... 50

Transport ....................................................................................51

Disposal and recycling ...............................................................51

Troubleshooting .........................................................................51

Warranty Details ........................................................................ 55

Repair and Refurbished Goods or Parts Notice ....................... 56

Table of Contents

Need help?

Do you have a question about the 25CC and is the answer not in the manual?

Questions and answers

Summary of Contents for FERREX 25CC

Page 1: Table Of Contents
Introduction ................12 Layout ..................13 Scope of delivery ................14 Intended use ................15 25CC PETROL CHAINSAW ALDI guarantees that our exclusive brand products are developed to our Safety regulations ..............16 stringent quality specifications. If you are not entirely satisfied with this Set up ..................25 product, please return it to the nearest ALDI store within 60 days from the Operation ...................
Page 2: Package Contents/Part List
Package contents/part list Petrol Chainsaw Chain protection cover Combination wrench Allen wrench Fuel mixing bottle Abschließender Schnitt hier. 5 cm über der Keilmitte. Pos.4 Warranty card 5 cm Erster Pos.1 Pos.4 Schnitt Instruction manual Pos.1 Pos.1 Fluchtweg Keil Pos.2 Pos.2 5 cm Pos.2 Fallrichtung...
Page 3 Kapitelüberschrift Pos.1 Pos.2 Oberschnitt Unterschnitt Erster Schnitt auf belasteter Pos.1 Pos.2 Pos.1 Stammseite Zweiter Schnitt Mit Stammseite Pos.2 Pos.2 Schnitt Pos.2 Pos.2 Zweiter Schnitt Erster Schnitt auf der belasteten Mit Stützbock Pos.2 Schnitt Schnitt Stammseite Pos.2 Pos.1 Pos.2 Schnitt Pos.1 Pos.2 Pos.1 Schnitt...
Page 4 Kapitelüberschrift Fig. 1 Fig. 1 Fig. 2 Fig. 2 Fig. 3 Fig. 3 Fig. 1 Fig. 2 Fig. 2 Fig. 3 Fig. 4 Fig. 4 Fig. 5 Fig. 5 Fig. 6 Fig. 6 Fig. 4 Fig. 5 Fig. 3 Fig. 5 Fig.
Page 5 Kapitelüberschrift 0,5 mm A 20...
Page 6: Explanation Of Symbols
Kapitelüberschrift Explanation of Symbols Read, understand and follow all warnings. WARNING! Risk of kickback. Protect yourself from kick- back from the chainsaw and avoid all contact with the bar tip. Do not use the device with one hand. Use the device with both hands. Always wear safety glasses, hearing protection and a safety helmet Read the complete user guide before using the appli-...
Page 7 Explanation of Symbols Kapitelüberschrift Fuel and oil mixture 40: 1 40:1 Number of revolutions Filling hole for chain oil. Choke knob Setting the chain tension: White arrow: Loosen chain Black arrow: Tighten chain Installation direction of chain Guaranteed sound power level of the device. Attention! Hot surface Weight Comply with the Australian safety standards.
Page 8: Introduction
Kapitelüberschrift Introduction Introduction Congratulations on choosing to buy a FERREX product. ® All products brought to you by FERREX are manufactured to the highest standards ® of performance and safety, and as part of our philosophy of customer service and satisfaction, are backed by our comprehensive 1 Year Warranty.
Page 9: Layout
Kapitelüberschrift Layout Layout (Fig. 1) Chain Guide bar Hand Guard / Chain Brake Lever Fuel pump (Primer) Throttle lever Rear Handle Safety locking button (throttle lock) Starter grip Air filter cover Fan housing with starting assembly Oil tank cap Front grip (tubular handle) Fuel tank cap Choke switch I/STOP-switch (short-circuit switch)
Page 10: Scope Of Delivery
Kapitelüberschrift Scope of delivery Scope of delivery Petrol Chainsaw (1x) Chain protection cover (1x) Combination wrench (1x) Allen wrench (1x) Fuel mixing bottle (1x) Warranty card (1x) Instruction manual (1x) Open the packaging and take out the equipment with care. •...
Page 11: Intended Use
Kapitelüberschrift Intended use Intended use This machine is a particularly light and easy to handle chain saw with overhead mounted handle. This chainsaw is designed especially for tree care and surgery. These chainsaws may therefore only be operated by “Chainsaw operators with addi- tional training for work using raised platforms or ladder platforms and/or using rope climbing techniques”.
Page 12: Safety Regulations
Kapitelüberschrift Safety regulations Safety regulations General notes • To ensure a safe use the operator has to read and follow all safety pre- cautions in the owner’s manual to familiarize himself with the handling of the chain saw. Failure to follow instructions could result in serious injury.
Page 13 Safety regulations Kapitelüberschrift • To avoid hearing damage wear your proper personal sound protection equipment (ear plugs or ear muffs, etc.) • The safety/cut protection jacket has layers of woven nylon in it and protects against cuts. It must always be worn when working in raised platforms or ladder platforms and when using rope climbing techniques.
Page 14 Kapitelüberschrift Safety regulations Fuels / Refuelling • When refuelling the chain saw the engine must be switched off. • Smoking and open fire are not permitted. • Before refuelling allow the machine to cool down fully. • Fuels might contain solvent-like substances. Avoid skin and eye contact with mineral oil products.
Page 15 Safety regulations Kapitelüberschrift • Before starting the saw the operator has to ensure a good footing. • Only start the saw as described in this manual. Other starting techniques are not permitted. • When starting up, the machine must be safely supported and firmly held. The bar and chain must be free-standing.
Page 16 Kapitelüberschrift Safety regulations operator in an uncontrolled, high-energy manner (risk of injury!). To avoid a kickback please note following instructions: • Plunge work (directly plunging the tip of the bar into the wood) may only be performed by specially trained personnel! •...
Page 17 Safety regulations Kapitelüberschrift • Round wood or logs should be secured against turning while they are be- ing cut. • For felling or cross-cutting, the spike bar (claw stop) must be applied to the wood to be cut. The use of the spike bar is also recommended when cutting through thick branches.
Page 18 Kapitelüberschrift Safety regulations • Felling work may only be started when it has been ensured that: a) Only persons involved in the felling work are in the felling area, b) An obstacle free path to the rear is available for everyone involved in the felling work (this rearwards path must run straight back at approx.
Page 19 Safety regulations Kapitelüberschrift • Watch out for rolling logs. Transport and storage • When carrying and changing your position while working with the chain saw the engine must be stopped or the chain brake has to be ac- tivated to avoid an unintentional running of the chain. •...
Page 20 Kapitelüberschrift Safety regulations Use only original spare parts and accessories. Not using original spare parts, accessories, guard chain combinations and lengths will lead to an increased risk of injuries. In case of accidents or damages caused by using unauthorised sawing devices or accessories refuse all liability. First aid For potentially occurring accidents, the First Aid kit, according to DIN 13164, should always be handy at the work place.
Page 21: Set Up
Safety regulations/Set up Kapitelüberschrift Remaining risks m DANGER RISK OF INJURY ! Contact with the saw-chain can lead to fatal cutting injuries. Never put your hands into the running saw-chain. RISK OF KICKBACK! Kickback can lead to fatal cutting injuries. RISK OF BURNING! The chain and the guide bar heat up during operation.
Page 22 Kapitelüberschrift Set up turn the chain tensioning screw in an ANTI-CLOCKWISE DIRECTION, the chain ten- sion will be reduced. Check that the chain is seated around the entire chain bar (Fig. 3/pos. X3). After making the adjustment and with the tip of the bar still upwards, tighten •...
Page 23 Kapitelüberschrift Set up m WARNING The purpose of the chain brake is to reduce the possibility of injury due to kickback; however, it cannot provide the intended measure of protection if the saw is oper- ated carelessly. Always test the chain brake before using your saw and periodically while on the job.
Page 24 Kapitelüberschrift Set up Recommended fuels Some conventional petrols are being blended with oxygenates such as alcohol or an ether compound to meet clean air standards. Your engine is designed to oper- ate satisfactorily on any petrol intended for automotive use including oxygenated petrols.
Page 25: Operation
Kapitelüberschrift Operation Operation Please note that the statutory regulations governing noise abatement may differ from one location to another. Each time before use, check the following: That there are no leaks in the fuel system. That the equipment is in perfect condition and that the safety devices and cutting devices are complete.
Page 26 Kapitelüberschrift Operation m CAUTION Since the choke switch (Fig. 9/arrow direction 1) is closed, the chain starts to move and rotate AT HIGH SPEED, immediately when the engine is started. Let the engine run for 10 seconds to warm up. Press the safety locking button (7) &...
Page 27: Operating Instructions
Operation/Operating Instructions Kapitelüberschrift SWITCHING OFF THE ENGINE Emergency Stop procedure: To stop the engine in an emergency, activate the Hand Guard / Chain Brake Lever (Fig.6/pos. 3). This will immediately stop the chain. Then switch the stop switch (Fig. 8/pos. 15) to ‘0’ Stop. Normal procedure: Let go of the throttle lever (Fig.
Page 28 Kapitelüberschrift Operating instructions Press the casing of the chainsaw against the log when starting sawing. Run the device at full throttle throughout the whole sawing process. Let the saw do the work. Only use slight downwards pressure. Release the throttle as soon as you have finished your work so the motor runs idle. If you let the machine run at full throttle without load, there will be unnecessary wear and tear.
Page 29 Operating instructions Kapitelüberschrift Look out for destroyed or decayed parts of the tree. If the trunk is decayed, it can suddenly break and fall on you. Make sure there is suffi- cient space for the falling tree. Keep a distance of 2½ tree lengths to the next person or other objects.
Page 30 Kapitelüberschrift Operating Instructions Be aware of signs that the tree is beginning to fall: Cracking sounds, the dropping cut opening or movement in the upper branches. When the tree begins to fall, stop the saw, put it down and leave immediately via your escape route.
Page 31 Operating Instructions Kapitelüberschrift Topping (Fig. E, Pos. 1) Topping starts at the upper side of the log where you hold the saw against the log. Only use slight downwards pressure for topping. Undercut (Fig. E, Pos. 2) Start the undercut on the underside of the log and hold the top edge of the saw against the log.
Page 32 Kapitelüberschrift Operating Instructions m CAUTION Never climb into the tree for trimming or pruning. Do not stand on ladders, platforms etc. You could lose your balance and control of the device. Important notices Work slowly and hold on to the saw with both hands. Ensure a secure standing posi- tion and balance.
Page 33 Operating Instructions Kapitelüberschrift WORKING WITH TREE SERVICE CHAIN-SAWS FROM A ROPE AND HARNESS This chapter sets out working practices to reduce the risk of injury from tree service chainsaws when working at height from a rope and harness. While it may form the basis of guidance and training literature, it should not be regarded as a substitute for formal training.
Page 34 Kapitelüberschrift Operating Instructions When moving the saw from any attachment point to another, operators should en- sure it is secured in the new position before releasing it from the previous attach- ment point. Using the chainsaw in the tree An analysis of accidents with these saws during tree service operations shows the primary cause as being inappropriate one-handed use of the saw.
Page 35 Operation Instructions Kapitelüberschrift • on the right side, hold the saw with the right hand on either handle and thrust the saw away from the body while holding the pull starter cord in the left hand. The chain brake should always be engaged before lowering a running saw onto its strop.
Page 36: Cleaning
Kapitelüberschrift Operating Instructions/Cleaning LIMBING a) Always start from the larger diameter and move towards the tip to cut off limbs and any secondary branches. b) Always find the safest and most stable position before accelerating the chainsaw. If necessary, keep your balance by resting your knee on the trunk itself. c) Keep the chainsaw on the trunk so as not to get too tired, turning it onto the left- or right-hand side depending on the position of the branch to cut (Fig.
Page 37: Maintenance And Servicing
Maintenance and servicing Kapitelüberschrift Maintenance and servicing MAINTENANCE m CAUTION All maintenance work on the chainsaw apart from the work described in this manual may only be carried out by authorised after-sales service personnel. Chain brake operational test Test the chain brake periodically to ensure proper function. Perform a chain brake test prior to initial cutting, following extensive cutting, and definitely following any Chain brake service.
Page 38 Kapitelüberschrift Maintenance and servicing Air Filter m NOTICE Never operate the saw without the air filter. Dust and dirt will be drawn into the engine and damage it. Keep the air filter clean! The air filter must be cleaned or re- placed after every 20 hours of service.
Page 39 Maintenance and servicing Kapitelüberschrift lower corner of the tank. If necessary, use a long screwdriver to move the filter to its correct position, taking care not to damage it in the process. Fill tank with fresh fuel / oil mixture. Securely refit the fuel tank cap (Fig. 7/pos. 13).
Page 40 Kapitelüberschrift Maintenance and servicing Chain bar maintenance (Fig. 16) Regular lubrication of the chain bar (guide rail for the chain and teeth) is essential. The chain bar needs the maintenance described in the following section in order for the saw to work at an optimum level of performance. m NOTICE The sprocket tip on your new saw has been pre-lubricated at the factory.
Page 41 Maintenance and servicing Kapitelüberschrift Turning the guide bar The guide bar should be reversed every 8 working hours to ensure uniform wear. Unscrew the retaining nut-sprocket guard (Fig. 1/pos. 16) with the combination wrench (Fig. 1/pos. 23) and remove the sprocket guard (Fig. 1/pos. 17). Keep the bar groove and lubrication hole clean (Fig.
Page 42 Kapitelüberschrift Maintenance and servicing Instructions for sharpening a saw chain: File Upper tilt Standard diameter Upper angle Lower angle anglel (55°) depth (not included) Chucking Chucking rota- inclination side angle tion angle angle ca. 4.0 mm 30° 0° 80° 0.64 mm depth stop file CHAIN MAINTENANCE (CONTINUED)
Page 43 Maintenance and servicing Kapitelüberschrift m CAUTION Never have more than 3 links removed from a loop of chain. This could cause damage to the sprocket. Re-assembly of the chain bar and chain to the engine unit m CAUTION Do not start the engine until the saw is fully assembled. m CAUTION Wear protective gloves at all times when handling the chain.
Page 44 Kapitelüberschrift Maintenance and servicing Oil passages Oil passages on the bar should be cleaned to ensure proper lubrication of the bar and chain during operation. m NOTICE The condition of the oil passages can be easily checked. If the passages are clear, the chain will automatically give off a spray of oil within seconds of starting the saw.
Page 45: Technical Data
Kapitelüberschrift Technical data Technical data Engine displacement 25 cm³ Maximum engine capacity 0.7 kW (1 HP) Cutting length 20 cm Cutter rail type 10” Chain pitch (3/8”), 9.525 mm Chain thickness (0.05”), 1.27 mm Chain sprocket - Number of teeth and pitch 6 x 9.525 mm Idling speed 3300±300 min...
Page 46: Storage
Kapitelüberschrift Technical data/Storage Sound and vibration Sound pressure level L 99.2 dB(A) Uncertainty K 3 dB(A) Guaranteed sound power level L 113 dB(A) Measured sound power level L 110.4 dB(A) Uncertainty K 3 dB(A) Vibration Front Handle a 8.98 m/s² Vibration Rear Handle a 8.03 Uncertainty K...
Page 47: Transport
Storage/Transport/Disposal and recycling/Troubleshooting Kapitelüberschrift Putting the equipment back into operation Remove the spark plug. Quickly tug on the starter line to remove excess oil from the combustion chamber. Clean the spark plug and check that the electrode gap is correct, or insert a new spark plug with the correct electrode gap.
Page 48 Kapitelüberschrift Troubleshooting Troubleshooting guide Problem Probable cause Corrective Action Incorrect starting proce- Follow instructions in the User dures. Manual. Incorrect carburettor Unit won’t start or Have carburettor adjusted by an mixture adjustment starts but will not Authorized Service Center. setting. run.
Page 49 Kapitelüberschrift Troublshooting Service information Please note that the following parts of this product are subject to normal or natural wear and that the following parts are therefore also required for use as consumables. Wear parts* Saw chain, Chain bar, Saw chain-oil, Motor-oil, Spiked bumper, Chain catcher, Spark plug, Air filter, Fuel filter, Saw chain-oil filter To order spare parts, use the spare part drawing of this manual.
Page 50 Kapitelüberschrift...
Page 51: Warranty Details
PETROL CHAINSAW 25CC Warranty Details REGISTER YOUR PURCHASE AT www.aldi.com.au/en/about-aldi/product-registration/ TO KEEP UP-TO-DATE WITH IMPORTANT PRODUCT INFORMATION The product is guaranteed to be free from defects in workmanship and parts for a period of 12 months from the date of purchase. Defects that occur within this warranty period, under normal use and care, will be repaired, replaced or refunded at our discretion.
Page 52: Repair And Refurbished Goods Or Parts Notice
PETROL CHAINSAW 25CC Repair and Refurbished Goods or Parts Notice TO KEEP UP-TO-DATE WITH IMPORTANT PRODUCT INFORMATION Unfortunately, from time to time, faulty products are manufactured which need to be returned to the Supplier for repair. Please be aware that if your product is capable of retaining user-generated data (such as files stored...

FERREX 25CC User Manual

Quick Links

Need help?

Questions and answers

Related Manuals for FERREX 25CC

Summary of Contents for FERREX 25CC

Table of Contents