Advertisement
Quick Links
CW232·CW232/V·CW422
Introduction
Thank you for your choosing our RS232C/RS422 Analyzer 【CW232(V)/CW422】.
This manual will give you some notices about how to use this product.
Please read the content before you use the product.
※
Please agree to omit (V) of CW232/V in the following sentences, and to unite it only to the mark
named CW232/CW422.
Package Contents
・
Simple manual (this book)
・
Install CD-ROM
・
CW232/CW422 main body
・
USB cable
※ Please contact our Sales Department though it descends to the packing of the product with
scrupulous care if any of the above items of the package is missing.
System Requirement
□Correspondence OS: Windows98SE / 2000 / XP
□Recommended environment:
CPU _______Intel Pentium / Celelon 800MHz or above
RAM ______256 MB or above
HDD_______300 MB free space or above
USB _______USB1.1 or above
Others______External Graphic Card instead of the built-in one is recommended.
Notification
※ Memory and hard disk capacity necessary for operating the program might be different depending on
the system environment used.
※ It should be tested in the above-mentioned, recommended environment, otherwise it probably
exists some instance that operation cannot be completely guaranteed according to customer's
environment.
※ Various specifications of the product are subjected to variation without a previous notice. Please
acknowledge it beforehand.
※ Please not connect it to interfaces other than USB and RS232C/RS422.It cause damage and fire, etc.
※ Please not put it on moisture, dust, lamp soot or damp.
※ Please not use or leave it in the place of the high temperature like the place where direct
sunshine in close contact with the heater strikes.
※ Please not put the foreign body internally to remodel it.
※ Please not touch by a wet hand.
※ Please remove all cables at once and not go on using when generation of heat is felt or abnormality
such as smelling to strangeness is confirmed by any chance. Please contact the shop of purchase.
Simple User's Manual
When the application program is installed, the CD-ROM driver is necessary.
（Compact Watch RS232C/RS422 Analyzer）
Ver1.1
2006.3 DATA LINK Co., Ltd
It causes fire etc.
It causes fire etc.
It causes fire, the electric shock, and the injury.
It causes the electric shock.
Advertisement
Summary of Contents for Data Link CW232
- Page 1 This manual will give you some notices about how to use this product. Please read the content before you use the product. ※ Please agree to omit (V) of CW232/V in the following sentences, and to unite it only to the mark named CW232/CW422. Package Contents ・...
- Page 2 Installation Instruction ・ Driver installation (Windows98) After insert attached CD-ROM in PC, connect CW232/CW422 main body to the USB socket on the PC by USB cable. ①When the following dialog box is displayed, click「Next」button. ② When「Please select the retrieval method」dialog box is displayed, please select「Search for the best driver for your device.」and click「Next」button.
- Page 3 ・ Driver installation (Windows XP) After insert attached CD-ROM in PC, connect CW232/CW422 main body to the USB socket on the PC by USB cable. When the following dialog is displayed, select「Install the software automatically (Recommended)」...
-
Page 4: Next」 Button
① 「Please select a setup type」screen: ○Complete(C) is selected usually. ② 「Ready to install the program」the screen: When「Install (I)」was clicked, the installation begins. ③ 「InstallShield Wizard completed」the screen: click「Finish (F)」and installation ends. ④ CW232/422 is started from a start menu or a desktop icon. - Page 5 Begin the monitor. End the monitor. ③ The status bar: Connected state, the transmission rate and the version of CW232/422 F/W are displayed. ④ The count bar: The number of data receptions from the equipment connected with the CH1 side is displayed in TXD.
- Page 6 5) It is assumed the state that can be communicated by turning on the power supply of the device at monitored both ends. 6) The CW232/422 application program is set, and it is assumed the state of the monitor beginning. 7) The communication that wants to be actually monitored between devices at both ends begins.
- Page 7 Use Method ※ After the equipment is connected like the example of the above-mentioned example,「Analyzer application program CW232/422」installed in PC can be started. ① Setup the serial communication condition. Menu[Settings]->[COM Settings] Baud rate: 50/100/110/150/200/300/600/1200/2400/4800/9600/14400/19200/28800/38400/57600/76800/115200 ※ Under baud rate whether data can be monitored depends on the processing performance of PC.
- Page 8 ③ Click monitor beginning button . The data that flows on RS232C/RS422 is monitored. The monitor data is preserved in the memory of PC. Though the data that can be preserved depends on the image resolution etc. of PC, the preservation for about 2048 Line is possible.
- Page 9 ※ Please refer to an online manual for other use. Error Message If the main body of CW232/CW422 connection is not recognized when analyzer application program CW232/CW422 is started, the following dialog box is displayed. ※ When this message is displayed, analyzer application program CW232/422 is ended once.
- Page 10 ･ CW232/CW422 receives the power supply when connected to PC by an attached USB cable and starts. At this time, 2-3 second later, LED in the upper part of the main body becomes a green light after red lights(It is normal.). CW232/CW422 is thought of abnormity when it is not lighting such LED.
- Page 11 Externals chat...
- Page 12 The guaranteed term of the Data Link product is one year from our consignment day. Because the product control goes with Serial No, the written guarantee is not being appended.
Need help?
Do you have a question about the CW232 and is the answer not in the manual?
Questions and answers