Related Manuals for Norden Mfg AE10
Summary of Contents for Norden Mfg AE10
- Page 1 Owner’s Manual AE10 Hay Accumulator Read and understand the manual. This manual provides information and MADE IN THE USA procedures to safely operate and maintain the Hay Accumulator.
-
Page 3: Table Of Contents
6.5.4 Inline Balers ....28 Lighting Socket Holder ....28 AE10 Hay Accumulator Norden Mfg (877) 296-5851... -
Page 4: Introduction
Record the serial quickly, as well as quicker stacking in the barn. number in the space provided for easy reference when contacting Norden Mfg LLC with questions. Please read the manual carefully to become familiar with your new Norden Hay Accumulator. -
Page 5: Owner/Operator Manual Storage
1.7 Disposal of Equipment at End of Useful Life The Norden Mfg LLC Hay Accumulator has been designed for the specific purpose of arranging bales into groups. When this unit is no longer capable of performing its intended use, it should be dismantled and scrapped. -
Page 6: Safety
NOTICE to other persons. Indicates that equipment or property damage can Norden Mfg LLC cannot anticipate every result if instructions are not followed. possible circumstance that might involve a potential hazard. The warnings in this... -
Page 7: Safety Icons Nomenclature
Defective or broken part Maintain safety signs Chock wheels Place in park Maintain safe distance Remove key Pinch point hazard Stop engine STOP Overturn hazard Visibility Negative tongue weight hazard Set parking brake Rollover hazard AE10 Hay Accumulator Norden Mfg (877) 296-5851... -
Page 8: General Operating Safety
Do not allow riders on the tractor If you do not understand any information in this or Hay Accumulator at any time. manual, see your dealer or contact Norden Mfg LLC Falling can result in severe injuries or death. before proceeding. -
Page 9: Sign-Off Form
2.8 Sign-Off Form Make periodic reviews of SAFETY and OPERATION of the Hay Accumulator a standard practice. An Norden Mfg LLC follows the general Safety untrained operator is not qualified to use this Hay Standards specified by the Farm Equipment Accumulator. -
Page 10: Operation Safety
2.12 Maintenance Safety Refer to “11. Maintenance” on page 37 for safety recommendations related to maintaining the Hay Accumulator. All applicable safety recommendations in other sections should also be followed. Norden Mfg (877) 296-5851 AE10 Hay Accumulator... -
Page 11: Safety Signs And Labels
4. Replacement parts must have replacement labels attached before the Hay Accumulator is used. 5. Labels are available from your authorized dealer or from Norden Mfg LLC at no charge. 3.2 Contact Information For replacement decals, contact: AE10 Hay Accumulator... -
Page 12: Safety Sign Locations
Item Type Description Qty. WARNING Read the Manual WARNING No Riders INFORMATIONAL Serial Number CAUTION Pinch Point WARNING Do Not Transport at Speeds Over 20 MPH WARNING Falling Hazard INFORMATIONAL Made in USA Norden Mfg (877) 296-5851 AE10 Hay Accumulator... -
Page 13: Hay Accumulator Safety Signs
FALLING HAZARD NO RIDERS Do not climb or stand on the unit at any time. Do not use the unit as a platform. KN-00047 Falling can result in serious injury or death. KN-00053 AE10 Hay Accumulator Norden Mfg (877) 296-5851... -
Page 14: Names Of Major Parts
Gate #2 Belt Tensioner Gate #3 Hitch Gate #4 Chute Platform Gate Switch Front Tires, 20.5x8-10 Side Panels Reach Pole Dividers Rear Tires, ST225/75R15 Tail Lights Accumulator Bed Back Gate Slow Moving Vehicle Sign Norden Mfg (877) 296-5851 AE10 Hay Accumulator... -
Page 15: Undercarriage
KN-00281 4.5 Lights The Hay Accumulator is equipped with agricultural lights and an enhanced flasher lighting module to meet ASABE S279 standard. KN-00279 KN-00282 AE10 Hay Accumulator Norden Mfg (877) 296-5851... -
Page 16: Linkage System Operation
3. Bale #2 enters the Hay Accumulator and slides downward and into position, rotating the gate 6. Bale #5 enters the Hay Accumulator and slides actuating spring, and shifting gate #1 to open downward and into position. row #2. KN-00288 KN-00285 Norden Mfg (877) 296-5851 AE10 Hay Accumulator... - Page 17 #4 to open row the ground. When all bales are clear, the back gate returns to its original position and latches. All gates return to their original position. KN-00291 KN-00294 AE10 Hay Accumulator Norden Mfg (877) 296-5851...
-
Page 18: Assembly
2. Bolt the chute platform sides to the chute platform and the accumulator bed using three 3/8 x 3/4” serrated flange bolts and nuts on each side. Do not fully tighten the bolts. KN-00246 Norden Mfg (877) 296-5851 AE10 Hay Accumulator... - Page 19 Do not fully tighten the bolts. KN-00300 9. Bolt the chute dog to the mount using two 3/8 x 3/4” serrated flange bolts and nuts. Tighten the bolts to the proper torque value. KN-00298 KN-00301 AE10 Hay Accumulator Norden Mfg (877) 296-5851...
- Page 20 Do not fully left side of the base chute using two 3/8 x 3/4” tighten the bolts. serrated flange bolts (2) and nuts. Do not fully tighten the bolts. KN-00304 KN-00302 Norden Mfg (877) 296-5851 AE10 Hay Accumulator...
- Page 21 3/8 x serrated flange bolts and nuts. Do not fully 3/4” serrated flange bolts and nuts. Do not fully tighten the bolts. tighten the bolts. KN-00308 KN-00306 AE10 Hay Accumulator Norden Mfg (877) 296-5851...
- Page 22 KN-00309 KN-00310 18. Bolt the SMV sign into position using two 5/16 x 3/4” bolts with nylon lock nuts. Tighten the bolts to the proper torque value. KN-00247 Norden Mfg (877) 296-5851 AE10 Hay Accumulator...
-
Page 23: Set-Up
Only operate the tractor with the ROPS in the raised position and seat belt fastened. AE10 Hay Accumulator Norden Mfg (877) 296-5851... -
Page 24: Tractor Requirements
• To reduce the risk of fire, do not use a tractor with an underframe exhaust. KN-00248 • A loader with at least 1500 lb. lift capacity is required to handle the grouped bales. Norden Mfg (877) 296-5851 AE10 Hay Accumulator... - Page 25 ® proper hitch length. 6. Tighten the four carriage bolts on the sides of the chamber extension first, then the six flange bolts on the bottom. 0 - 2” KN-00311 KN-00249 AE10 Hay Accumulator Norden Mfg (877) 296-5851...
- Page 26 KN-00251 8. Ensure that the belt tensioner assembly is square with the belt by adjusting the angle of the belt tensioner assembly at its mounting point on the base chute. KN-00252 KN-00313 Norden Mfg (877) 296-5851 AE10 Hay Accumulator...
-
Page 27: Baler Chamber Settings
1987 and older NH balers have the hitch on the 14. Use a 3/8” leather punch or a 7/16” drill to make right hand side of the chamber. Norden Mfg. offers a three holes through the belt at the marked center hitch adaptor to center the hitch. -
Page 28: Newer New Holland® Balers
The hitch on the JD baler may need to be extended to meet the dimensions given in “6.3 Baler Hitch Setup” on page 24. Norden Mfg. offers a special hitch extension for John Deere® balers. If bolting to the chamber extension, it can use one of the lower bolts that hold the chamber extension in place. -
Page 29: Operation
3. Insert a high strength drawbar pin through the clevis and drawbar holes and install the retaining pin. Do not use a homemade or shop made pin. AE10 Hay Accumulator Norden Mfg (877) 296-5851... -
Page 30: Break In
Operate up and down (not side of the chute extension using the hairpin across) intermediate slopes. Avoid sudden starts retainers. and stops. If problems persist, call Norden Mfg. for service. 7.3.1 Break In 7.4.3 High Moisture Hay To quickly and effectively “break in” the Hay... -
Page 31: Troubleshooting
10-3/8”. KN-00322 KN-00319 2. Lengthen the cable to maintain the same position for the switch arm. 2. Shorten the cable to maintain the same position for the switch arm. KN-00323 KN-00466 AE10 Hay Accumulator Norden Mfg (877) 296-5851... -
Page 32: Back Gate Trip Adjustments
2. When the trip reach is pushed over to the right by trip reach. trip slider (3), it must not contact the bolt heads (4) on the bearing mount. Make sure there is clearance to the bolt heads. KN-00261 KN-00259 KN-00636 Norden Mfg (877) 296-5851 AE10 Hay Accumulator... -
Page 33: Transporting
Substandard safety chains could allow the unit during daylight and nighttime transport. Various safety lights and devices are to separate from the tow vehicle, resulting in available from your dealer. equipment damage and personal injury. AE10 Hay Accumulator Norden Mfg (877) 296-5851... -
Page 34: Setting The Hitch For Transport
1. Using a suitable lifting device, raise the front of the accumulator until the front wheels are off the ground. A jack mount is provided on the left front of the frame for this purpose. KN-00262 Norden Mfg (877) 296-5851 AE10 Hay Accumulator... -
Page 35: Pre-Towing Checklist
6. Prior to towing, have an observer confirm all running lights, brake lights, turn signals, and hazard lights are working on the tow vehicle. 7. Verify the brakes on the tow vehicle are operating correctly. AE10 Hay Accumulator Norden Mfg (877) 296-5851... -
Page 36: Storage
4. Lubricate all grease points. Make sure all grease cavities have been filled with grease to displace any trapped water from washing. 5. Touch up all paint nicks and scratches to prevent rusting. Norden Mfg (877) 296-5851 AE10 Hay Accumulator... -
Page 37: Maintenance
Unapproved parts could create a safety hazard. The manufacturer will not accept responsibility for damages as a result of the use of unapproved parts. AE10 Hay Accumulator Norden Mfg (877) 296-5851... -
Page 38: Lubrication
3. Grease the fittings on the trip flipper arm bearings annually with an SAE multipurpose lithium base If equipment has been altered in any way from the grease. original design, the manufacturer does not accept any liability for injury or warranty. KN-00325 Norden Mfg (877) 296-5851 AE10 Hay Accumulator... -
Page 39: Wheel Bearing Adjustment
2. Lift the tire and slowly rotate it while tightening the spindle nut. 3. Tighten the spindle nut until a slight drag is felt on the rotating wheel. 4. Re-install the dust cap and cotter pin. KN-00265 AE10 Hay Accumulator Norden Mfg (877) 296-5851... -
Page 40: Swivel Dolly Bushings
Before performing any type of welding repair to the Hay Accumulator, contact Norden Mfg. Start all bolts or nuts by hand to prevent cross for approval. Repair welding must be done threading. -
Page 41: Service Record
Inspect the belted base chute and tensioner for wear and damage. Make sure the hitch, hitch bolts, and hitch pin are in good condition. Do not use homemade or shop made pins. Wash the accumulator. AE10 Hay Accumulator Norden Mfg (877) 296-5851... -
Page 42: Parts Section
Remember, it is the users responsibility to maintain these decals. All decals must be in place and legible or all warranties are void. Norden Mfg (877) 296-5851 AE10 Hay Accumulator... -
Page 43: Hay Accumulator Undercarriage
Stop, Tongue Insert 1005200 Hub Assembly* 1007710 Bolt, Hex, 1 x 1-1/2” Grade 5 1015930 Bushing, Nonmetallic 1003600 Wheel, Front 1003570 Tire, 20.5 x 8 - 10 * Refer to separate page for parts. AE10 Hay Accumulator Norden Mfg (877) 296-5851... -
Page 44: Accumulator Bed
Bolt, Serrated Flange, 3/8 x 1” Grade 5 1006140 Washer, Flat, 5/16” SAE 1001060 Platform, Gate 1006290 Bolt, Hex, 5/16 x 1”, Grade 5 1006300 Bolt, Carriage, 3/8 x 3/4” 1007980 Tape, Reflective, 2” x 9”, Amber Norden Mfg (877) 296-5851 AE10 Hay Accumulator... -
Page 45: Twisted Chute
Nut, Serrated Flange, 3/8-16 1006310 Bolt, Carriage, 3/8 x 1” 1006300 Bolt, Carriage, 3/8 x 3/4” 1000790 Extension, Chute, Left 1000800 Extension, Chute, Right 1005261 Chute, Twisted, Narrow Spacing 1005241 Chute, Twisted, Wide Spacing AE10 Hay Accumulator Norden Mfg (877) 296-5851... -
Page 46: Linkage System
12.7 Linkage System Norden Mfg (877) 296-5851 AE10 Hay Accumulator... - Page 47 Bolt, Hex, 1/2 x 1-3/4” Grade 5 1007270 Bolt, Hex, 7/16 x 1-1/4” Grade 5 1006110 Nut, Lock, Nylon, 1/2-13 1006200 Nut, Serrated Flange, 7/16-14 1000621 Reach, Back Gate Trip 1001361 Trip Flipper, Back Gate AE10 Hay Accumulator Norden Mfg (877) 296-5851...
-
Page 48: Hub Assembly
Stud, Wheel 1003680 Nut, Lug 1003650 1003730 Fitting, Grease 1005220 Race, Bearing, Outer 1005210 Race, Bearing, Inner Service Kit, Includes items 1, 2, 3, 4, 5, — 1009450 — 6, 7, 12, 13 Norden Mfg (877) 296-5851 AE10 Hay Accumulator... -
Page 49: Belt And Tensioner
1006770 Belt End Plate, Small 1003390 Saddle, Belt, Left 1006310 Bolt, Carriage, 3/8 x 1”, Grade 5 1003400 Saddle, Belt, Right 1006590 Spring, Belt Tensioner 1006400 Bolt, Hex, 5/8 x 1-1/2”, Grade 5 AE10 Hay Accumulator Norden Mfg (877) 296-5851... -
Page 50: Bale Chamber Extension
1004440 Side, Chamber Extension, Right 1006320 Bolt, Carrriage, 3/8 x 1-1/4”, Grade 5 1006330 Bolt, Serrated Flange, 3/8 x 3/4”, Grade 5 1006190 Nut, Serrated Flange, 3/8-16, Grade 5 1006910 Pin, Cotter, Reuseable Norden Mfg (877) 296-5851 AE10 Hay Accumulator... -
Page 51: Lighting
Light, Rear, Right 1008020 Harness, Baler Extension, 23’ (Not Shown) 1007620 Bolt, Hex, 1/4 x 1”, Grade 5 1006070 Nut, Lock, Nylon, 1/4-20, Grade 5 1007990 Tape, Reflective, 2” H x 9”, Red AE10 Hay Accumulator Norden Mfg (877) 296-5851... - Page 52 NOTES Norden Mfg (877) 296-5851 AE10 Hay Accumulator...
- Page 53 NOTES AE10 Hay Accumulator Norden Mfg (877) 296-5851...
- Page 54 NOTES Norden Mfg (877) 296-5851 AE10 Hay Accumulator...
- Page 56 Norden Mfg LLC 4210 Kinsman Road NW North Bloomfield, OH 44450 www.Nordenmfg.com (877) 296-5851 support@Nordenmfg.com 1008350 Rev. F Revised 11-05-2021...
Need help?
Do you have a question about the AE10 and is the answer not in the manual?
Questions and answers