Advertisement
Quick Links
Thank you for choosing Jacksons Fencing. Our high quality fencing products will last for years
and give you trouble-free service if you follow the installation instructions below, which are
offered as a general guide. Read the instructions fully before starting assembly especially if
additional bin is to be assembled as well.
PLEASE NOTE:
THE WHEELIE BIN STORE IS DESIGNED TO CONCEAL VARIOUS RECYCLING
BINS. IT IS NOT DESIGNED TO BE WATERPROOF. PLEASE TAKE THIS INTO ACCOUNT IF THE
INTENTION IS TO USE THIS STORE FOR OTHER PURPOSES.
Tools required:
Drill / Screw Driver
Assembly Parts List (For Standard Wheelie Bin Store)
PARTS LIST
S#
Description
Timber Components
1
Back Panel
2
Left Hand Side Panel
3
Right Hand Side Panel
4
Left Hand Door
5
Right Hand Door
6
Left Hand Top Cover
7
Right Hand Top Cover
Metal Components
8
Tie Bar (Top)
9
Tie Bar (Bottom)
10
Door Handles
11
Door Latches
Fittings & Tools
12
M5 x 90mm Screws
13
M4 x 25mm Screws
14
Screw Caps
15
M5 x 45mm Screws
16
M4 x 40mm Screws
17
M4 x 25mm Screws
18
T25 Drive Bit
19
Pozi Drive Bit
T25 Drive Bit
Pozi Drive Bit
Jacksons Fencing Head Office, Stowting Common, Ashford, Kent, TN25 6BN
+44 (0) 1233 750393 |
DRB approved (ACT) 28/03/2019
How to Install a Wheelie Bin Store
Qty
01
01
01
01
01
01
01
01
01
02
02
06
24
02
06
02
08
01
01
Tie Bar
Top
www.jacksons-fencing.co.uk
|
JFW 40 Issue 08
Level
Tape Measure
Note:
All timber components are labelled.
Labels are attached to the Top End of each
component e.g. the following picture shows a
Left Hand Door with label attached to top of
the Door.
Door Handles +
Fixings
info@jacksons-fencing.co.uk
19mm Spanner
Label
(For Timber Components)
Tie Bar
Bottom
Door Latches
Page 1 of 9
Advertisement
Summary of Contents for Jacksons Fencing Wheelie Bin Store
- Page 1 How to Install a Wheelie Bin Store Thank you for choosing Jacksons Fencing. Our high quality fencing products will last for years and give you trouble-free service if you follow the installation instructions below, which are offered as a general guide. Read the instructions fully before starting assembly especially if additional bin is to be assembled as well.
- Page 2 Assembly Instructions: Note: It is important to note that assembling a Wheelie Bin Store is a two person operation. The Wheelie Bin Store must be assembled on a FLAT SURFACE to make sure it is square when assembled. It is also...
- Page 3 1 No M5 x 45mm screw for each end of Bottom Tie Bar Bottom Tie Bar Jacksons Fencing Head Office, Stowting Common, Ashford, Kent, TN25 6BN +44 (0) 1233 750393 | www.jacksons-fencing.co.uk info@jacksons-fencing.co.uk DRB approved (ACT) 28/03/2019 JFW 40 Issue 08...
- Page 4 10-15mm Gap Top of Both doors between doors in aligned closed position Jacksons Fencing Head Office, Stowting Common, Ashford, Kent, TN25 6BN +44 (0) 1233 750393 | www.jacksons-fencing.co.uk info@jacksons-fencing.co.uk DRB approved (ACT) 28/03/2019 JFW 40 Issue 08...
- Page 5 Chain fixed to the Right Hand Side Panel at the marked position This will complete the assembly of the Standard WHEELIE BIN STORE. Jacksons Fencing Head Office, Stowting Common, Ashford, Kent, TN25 6BN +44 (0) 1233 750393 | www.jacksons-fencing.co.uk info@jacksons-fencing.co.uk...
-
Page 6: Parts List
It is important to note that if an additional store is bought separately, the Top Cover provided is to be exchanged with the Right Hand Top Cover of the main Wheelie Bin Store when viewed from front to give same overhang on each side. - Page 7 Step 2: Remove the Right Hand Top Cover of the assembled Standard Wheelie Bin Store if Additional Bin Store is required to be added latter. Fix the Additional Back Panel to the rear right hand corner of the store using 2 no M5 x 90 screws as shown by the markings shown as Red circles below.
- Page 8 Additional Side Panel (as shown in Step3), but are not marked on the original right hand side panel of the Standard Wheelie Bin Store. The Top Tie Bar has a receiver plate attached to it on the right hand end.
- Page 9 This will complete the assembly of the Additional Wheelie Bin Store. Standard Wheelie Bin Store with Additional Unit Open Position Closed Position Additional Store Shelf (Optional): Please note that shelf can only be fitted to the Additional Store because the main unit does not have a mid-panel to support any shelf.
Need help?
Do you have a question about the Wheelie Bin Store and is the answer not in the manual?
Questions and answers