Download
Share
Print this page
  1. Manuals
  2. Brands
  3. COVER VALET Manuals
  4. Hot Tub
  5. PRO
  6. Quick start manual

COVER VALET PRO Quick Start Manual

Premium hot tub cover lifter
Hide thumbs Also See for PRO:

Advertisement

Quick Links

Download this manual
PRO
TM
P
H
t
C
L
remium
ot
ub
over
ifter
TM

Advertisement

loading
Need help?

Need help?

Do you have a question about the PRO and is the answer not in the manual?

Questions and answers

Related Manuals for COVER VALET PRO

Summary of Contents for COVER VALET PRO

  • Page 1 remium over ifter...
  • Page 2 arts Channel Bracket (prBB) Side Mount Bracket (prAA) Locking Gas Shock (prLS) Regular Gas Shock (prRS) Pivot Arm (prCC) Extension Arm (prDD) Connection Bar 1 (prEE-a) Connection Bar 2 (prFF-a) Connection Bar 3 (prFF-b) Finger (prEE-b)
  • Page 3 ardware Large Screw Cap Lag Screw (prA) (prJ) Long Hex Bolt (prB) Medium Screw Cap (prK) Medium Hex Bolt (prC) Small Screw Cap (prL) Short Hex Bolt (prD) Large Washer (prM) Large Lock Nut (prE) Small Washer (prN) Small Lock Nut (prF) Plastic Support Self Tapping Screw (prG) (prPS)
  • Page 4 ssembling rAcket NARROW WIDE Figure 1 Note: The Side Mount Bracket (prAA) has a wider side and a narrower side. If your cover is extra wide mount the Channel Bracket (prBB) so the wider side extends outward. (See Figure 1) •...

  • Page 5: Mounting Bracket

    ounting brAcket Figure 2 Figure 3 • Place the assembled bracket against the side of the spa. The Side Mount Bracket (prAA) must be flush with the side of the spa. DO NOT allow the Side Mount Bracket (prAA) to hang over the rounded edge. (See Figures 2 and 3) •...
  • Page 6 nstAlling hocks Figure 4 The Locking Gas Shock (prLS) MUST be installed on the side of the spa where you will operate the lift. • Place the piston end of the Locking Gas Shock (prLS) into the Plastic Support (prPS) •...
  • Page 7 nstAlling ivot • Attach the Pivot Arm (prCC) to the Channel Bracket (prBB) using the Long Figure 5 Hex Bolt (prB), Screw Sleeve (prI), the Small Lock Nut (prF), and 2 Small Washers (pN). (See Figure 5) • Ensure that Pivot Arm (prCC) swings up and down easily.
  • Page 8 ssembling onnection bAr Depending on the width of your spa this step will vary. Start by measuring the distance between the Channel Brackets(prBB) mounted on the spa. 6½ nder • Each Connection Bar 1 (prEE-a) will slide inside each end of Connection Bar 2 (prFF-a).
  • Page 9 ssembling the over ifter • Insert Finger (prEE-b) into the hole on the Extension Arm (prDD) so it extends inward toward the tub. Fasten with Set Screw (prH) as shown in Figure 7. REPEAT THIS STEP ON THE OTHER EXTENSION ARM. BE SURE TO MOUNT THE FINGER FACING THE OPPOSITE DIRECTION.
  • Page 10 ssembling the over ifter *You will need at least one person to help hold the cover during this step Figure 10 • Slide the Extension Arms (prDD) into the Pivot Arms (prCC), making sure to center the spa cover over the spa. See Figure 10. •...
  • Page 11 *You will need at least one person to help hold the cover during this step • Fold Back the spa cover then manually lift the Cover Valet and spa cover to the upright position. • With the cover vertical, attach the Locking...
  • Page 12 EXCLUSIONS: A. This warranty does not cover damage incurred by the use of the Cover Valet and/or the spa cover, other than in accordance with the printed literature provided by California Home Spas, INC.