Page 1
Service Manual Ver. 2 INTEGRATED NETWORK AV RECEIVER Click here! AVR-X1300W On-line service parts list AVR-S720W We are getting ready. On-line owner’s manual http://manuals.denon.com/AVRX1300W/NA/EN/index.php http://manuals.denon.com/AVRX1300W/EU/EN/index.php http://manuals.denon.com/AVRX1300W/AP/ZH/index.php http://manuals.denon.com/AVRS720W/NA/EN/index.php CAUTION IN SERVICING ELECTRICAL MECHANICAL REPAIR INFORMATION UPDATING • For purposes of improvement, specifications and design are subject to change without notice. Please refer to the MODIFICATION NOTICE.
CAUTION IN SERVICING SAFETY PRECAUTIONS NOTE FOR SCHEMATIC DIAGRAM NOTE FOR PARTS LIST INSTRUCTIONS FOR HANDLING SEMICONDUCTORS AND OPTICAL UNIT CAUTION IN SERVICING. Initializing This Unit AVR-X1300W JIG FOR SERVICING Initializing This Unit AVR-S720W JIG FOR SERVICING...
SAFETY PRECAUTIONS ◎ Make a safety check after servicing! The following items should be checked for continued protection of the customer and the service Check that all screws, parts and wires removed or disconnected when servicing have been put back technician.
NOTE FOR SCHEMATIC DIAGRAM WARNING: Parts indicated by the z mark have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. CAUTION: Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check.
Page 5
CAUTION IN SERVICING. Initializing This Unit AVR-X1300W Initializing This Unit AVR-S720W Make sure to initialize this unit after replacing the microcomputer or any peripheral equipment, or the Make sure to initialize this unit after replacing the microcomputer or any peripheral equipment, or the digital PCB.
Page 11
E_POWER2 TU_CE E_POWER2 TU_SDIO TU_SDIO E_POWER1 TU_SCLK E_POWER1 TU_SCLK CEC_POWER2 CEC_POWER2 CPU_POWER VINA VINA CPU_POWER TO 9B VINB AVR-X1300W E3 MAIN_POWER VINB MAIN_POWER ONLY USE -12V DV_POWER R7566 DV_POWER TO B7 +12V OTHER OPEN SWM3.3V MIC_SIGNAL MIC_GND MCU_3V3 VOL_CLK D7501...
Page 12
SCH06_MCU_LEVEL_CHG CN762 CN761 TO BN502 TO BN501 MCU_LEVEL_CHG PART TO MAIN B'D TO MAIN B'D 2.0mm 9PIN WAFER 2.0mm 9PIN WAFER T7601 CN762 B_DETECT CN761 CJP08GI288ZY CJP09GI288ZY RLY_GND ANALOG MUTE_+B TO 6C FROM SWM3.3V DIGITAL DGND SUPPLY TO B8 R7601 AP_CK R7602 AP_DA...
Page 13
SCH07_DIR_SRC DIR/PLD PART (2) DIR output FROM HDMI_TX PART TO 8C CH1:FSDIR1 FROM MCU PART CH2:64FSDIR1 FROM/TO NETWORK PART TO B0 TO C4 CH3:DATADIR1 HDMI_I2S AP_CK AP_DA TO C5 AP_CS JTAG_TDOO (1) SPDIF input DR_CE JTAG_TCK DR_CK JTAG_TDI DR_DIN JTAG_TMS R7757 DR_DOUT CH1:RXIN0...
Page 14
SCH08_DSP DSP PART FROM PLD PART TO D0 FROM L7801 CB03YTYH600 DIGITAL SUPPLY DA1.0V L7802 CB03YTYH600 DA3V3 PART DGND TO B6 DSP_SDRAM DI_-/FR DI_-/SW DI_LRCK DI_BCK DI_F/FL R7809 D_RST DI_CSW/C DI_S/SL R7807 R7813 R7812 DI_SB/SR C7846 T7803 T7804 47uF/6.3V C7806 100/50V C7807 10/50V...
SCH15_FRONT BN12B1 FROM DIGITAL B'D 1.25mm 27PIN FFC TO CN751 FRONT PART FL101 BN12B1 AVRX1300W E3 ONLY CFL18BT021GINK CJP27GB286ZN PCB BRAKET *OPTION *Fuse RC101 F1001 E2/E1C/K 372Series BK101 BK102 T 200mA L 250V D1001 OPTION (37.9kHz) 932Series 1N4007SL Q1001 R1061 CMD1A572 KTC1027YT CMD1A572...
Page 22
T 1.25A L 250V BK301 CMD1A569 BRACKET BK302 CMD1A569 BRACKET BN302 Q3001 3.MCU_3V3 RT1P141C 2.B/P_IRIN_DE JK301 CJJ2D008Z 1.DGND TO CN754 AVR-X1300W E3 ONLY BK303 CMD1A387 BRACKET GND LINE POWER+ LINE POWER- LINE ANALOG AUDIO DIGITAL AUDIO TMDS SIGNAL ANALOG VIDEO STBY POWER...
Page 23
SCH17_SMPS SMPS PART OPTION OPTION E3,K T 2A L 250V C6002 250V/0.01uF OPTION *OPTION E2,E1C T 1.6A L 250V F6001 D6001 1N4007 D6002 1N4007 D6003 1N4007 D6004 1N4007 LF602 D6005 1N4007 E3,K:LF-4ZB-E273H E2,E1C:LF-4ZB-E503H D6006 1N4007 R6034 C6027 OPEN OPEN J6002 J6003 JUMPER JUMPER...
PRINTED CIRCUIT BOARDS DIGITAL, F HDMI, TUNER, HEADPHONE, HDMI_FFC_CABLE Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu). DIGITAL (A SIDE) F HDMI (A SIDE) F HDMI (B SIDE) MP_CUP12833Z_A C8136 R8122 T8109 T8112 C8208 R8124 C8134 L8101 C8109 R8270 C8123 DA_OUT CK_OUT...
Page 25
DIFF-AMP, BIAS-TR, PHONE WIRE GUIDE, TEMP_DETECT, FRONT CABLE GUIDE, BT WIRE GUIDE ,HDMI CABLE GUIDE, REGULATOR DIFF-AMP (A SIDE) DIFF-AMP (B SIDE) BIAS-TR (A SIDE) BIAS-TR (B SIDE) PHONE WIRE GUIDE (A SIDE) TEMP_DETECT (A SIDE) TEMP_DETECT (B SIDE) CUP12737Z-3 MP 2015.02.27 R2803 R2802 Q2104...
LEVEL DIAGRAM FRONT ch AVRS720W /X1300W LEVEL DIAG RAM FRO NT CHANNEL NJU72340A LINE IN M IC IN ZO NE2 SEL. SPK O UT 5M 80ZT FRO NT PCM 1690 PCM 9211 G AIN ADJ. ANALO G H/P O UT REC INH.
CENTER ch AVRS720W /X1300W LEVEL DIAG RAM CENTER CHANNEL NJU72340A SPK O UT CENTER 5M 80ZT PCM 1690 G AIN ADJ. CS49844A NJM 8080 M AX.O UTPUT 7.78Vrm s +30dB NJU72340 M AX.O UTPUT 3.8Vrm s SPK O UT 4.27Vrm s/8ohm PCM 1690 DIFF.O UT 0dBFS...
SUBWOOFER ch AVRS720W /X1300W LEVEL DIAG RAM SUBW O O FER CHANNEL NJU72340A PRE O UT M UTE SUBW O O FER 5M 80ZT PCM 1690 G AIN ADJ. CS49844A NJM 8080 M AX.O UTPUT 7.78Vrm s +30dB NJU72340 M AX.O UTPUT 3.8Vrm s FULL SCALE LEVEL=4.0Vrm s PCM 1690 DIFF.O UT...
SURROUND ch AVRS720W /X1300W LEVEL DIAG RAM SURRO UND CHANNEL NJU72340A SPK O UT SURRO UND 5M 80ZT PCM 1690 G AIN ADJ. CS49844A NJM 8080 M AX.O UTPUT 7.78Vrm s +30dB NJU72340 M AX.O UTPUT 3.8Vrm s SPK O UT 4.27Vrm s/8ohm PCM 1690 DIFF.O UT...
Page 32
SURR.BACK ch AVRS720W /X1300W LEVEL DIAG RAM SURRO UND BACK CHANNEL NJU72340A SPK O UT SURRO UND BACK 5M 80ZT PCM 1690 G AIN ADJ. CS49844A NJM 8080 M AX.O UTPUT 7.78Vrm s +30dB NJU72340 M AX.O UTPUT 3.8Vrm s SPK O UT 4.27Vrm s/8ohm PCM 1690...
Page 33
ZONE2 AVRS720W /X1300W LEVEL DIAG RAM ZO NE2 NJU72340A LINE IN SPK O UT BD3812F FRO NT ZO NE2 SEL. G AIN ADJ. ANALO G H/P O UT REC INH. NO T USE ZO NE2 O UT NJM 8080 M AX.O UTPUT 7.78Vrm s +30dB NJU72340 M AX.O UTPUT 3.8Vrm s SPK O UT...
Page 34
BLOCK DIAGRAM ANALOG AUDIO DIAGRAM AVRS720W /X1300W ANALO G AUDIO BLO CK H/P O UT H/P L G ND H/P R P-AM P SPK O UT ANA_FL ANA01 DA_FL DA01 ANA_FR ANA02 DA_FR DA02 M AIN TUNER FM /AM DA_CEN DA03 32.768kHz AUDIO IN...
Page 35
DIGITAL AUDIO DIAGRAM AVRS720W /X1300W DIG ITAL AUDIO BLO CK ADINL ADINR O PEN DIG TAL IN DIR_CE DAC_M UTE DIR_CLK DAC_RST M CLK1 O PT1(TV) DIR_DIN DAC_M S 256FSDIR1 DIR_DO UT DAC_DATA 64FSDIR1 DIR_RST DAC_CLK O PT2(CBL/SAT) FSDIR1 O PT.1 SBCK O PT.2 SLRCK...
Page 36
VIDEO DIAGRAM AVRS720W /X1300W VIDEO BLO CK ADV7623 HDM I RX(M N864788A) TRANSCEIVER P3 RX AD8195 F-HDM I IN6 Buffer (AUX) 28.6363M Hz O SD Block P2 RX HDM I IN1 (CBL/SAT) P1 TX P1 RX HDM I IN2 (DVD/BLU-RAY) O THER : 32M S.FLASH 32M /64M...
POWER DIAGRAM AVRS720W /X1300W VCC DIAG RAM HI+B M AIN+B LO W +B M AIN-B S1(AM P+B,-B) HI-B 25m A VO LUM E IC LO W -B (NJU72340A) M M 1Z7V5 259.63m A A+12V (NJM 8080,SPK/H-P/HI-LO W RELAY) 45m A DA+3.3V (PCM 5100) KIA7812BPI...
WIRING DIAGRAM AVRS720W /X1300W W IRING DIAG RAM AC CO RD ANT1 ANT2 CN754 REG UL.->DIG ITAL PCB TO PCB DIG ITAL PCB CN821 CN804 CY920 REG UL.->DIG ITAL CN823 CN802 CN508 CN801 SM PS->DIG ITAL CN741 CN762 CN701 CN602 CN751 CN822 CN761...
Page 39
SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. The semiconductor which described a detailed drawing in a schematic diagram are omitted to list. 1. IC's ADV7623 (DIGITAL_HDMI_ADV7623 : IC731) Pin No. Mnemonic Type Description RXC_2− HDMI input Digital Input Channel 2 Complement of Port C in the HDMI Interface.
Page 40
Pin No. Mnemonic Type Description Pin No. Mnemonic Type Description RXC_2− HDMI input Digital Input Channel 2 Complement of Port C in the HDMI Interface. PGND Ground PVDD Ground. RXC_2+ HDMI input Digital Input Channel 2 True of Port C in the HDMI Interface. PVDD Power PLL Supply Voltage (1.8 V).
Page 41
DIGITAL_HDMI_ADV7623 : IC732 ADV7623 Block diagram MX25L3206EM2I-12G (except : E2) MX25L6406EM2I-12G (ONLY E2) XTAL XTAL1 PIN DESCRIPTION VIDEO DATA SYMBOL DESCRIPTION RXA_C RXB_C SO/SIO1 HOLD# RXC_C Chip Select AUDIO DATA VIDEO DATA RXD_C Serial Data Input (for 1 x I/O)/ Serial Data SCLK SI/SIO0 RXA_0...
Page 43
Pin Name Symbol Pu/Pd STBY STOP Function Pin Name Symbol Pu/Pd STBY STOP Function STBY STBY "Pins for setting the operating mode(Select the HDMI transceiver w/ GUI(ADV7623) control pin (for P36/PO14/TIOCA2 HSDA (400k) Boot Mode or User Boot Mode,Single Chip Mode) C3VPu HDMI) M3VPu...
Page 44
Pin Name Symbol Pu/Pd STBY STOP Function Pin Name Symbol Pu/Pd STBY STOP Function STBY STBY P70/CS3#-B/ CEC standby power supply DIR RST DIR (PCM9211) control pin P96/AN14 CEC POWER ADTRG2# control(CEC5V,CEC3.3V,CEC1.8V) Power supply pin. Digital video power supply (DV5V,DV3.3V) control P95/AN13 DV POWER1 PB0/A8/PO24/...
Page 49
PCM1690DCAR (DIGITAL_MAIN DAC : IC791) TERMINAL PULL- DESCRIPTION NAME DOWN TOLERANT VOUT8+ Positive analog output from DAC8 VOUT8- Negative analog output from DAC8 VOUT7+ Positive analog output from DAC7 VOUT7- Negative analog output from DAC7 VOUT6+ Positive analog output from DAC6 VOUT6- Negative analog output from DAC6 VOUT5+...
Page 52
BD3812F BD3812F (DIGITAL_ANALOG : IC851) Application circuit TOP268VG (SMPS : IC601) 5-INPUT 3-OUTPUT VIDEO SWITCH 10µ DRAIN (D) CONTROL (C) OUT1 INTERNAL SUPPLY I GENERAL DESCRIPTION I PACKAGE OUTLINE SHUNT REGULATOR/ ERROR AMPLIFIER SOFT START 5.8 V 4.8 V OUT2 The NJM2595 is a 5-input 3-output video switch.
Page 54
MECHANICAL DISASSEMBLY Flowchart 1. FRONT PANEL ASSY 2. DIGITAL PCB 3. RADIATOR ASSY 4. SMPS PCB 5. REGULATOR PCB 6. TRANS POWER EXPLODED VIEW PACKING VIEW...
Page 55
DISASSEMBLY Flowchart • Remove each part following the flow below. • Reassemble the removed parts in the reverse order. • Read "SAFETY PRECAUTIONS" before reassembling the removed parts. • If wire bundles are removed or moved during adjustment or part replacement, reshape the wires after completing the work. Failure to shape the wires correctly may cause problems such as noise. •...
Explanatory Photos for DISASSEMBLY 1. FRONT PANEL ASSY • For the shooting direction of each photos used in this manual, see the photo below. • A, B, C and D in the photo below indicate the shooting directions of photos. Proceeding : TOP COVER →...
2. DIGITAL PCB 3. RADIATOR ASSY Proceeding : TOP COVER → DIGITAL PCB Proceeding : TOP COVER → DIGITAL PCB → RADIATOR ASSY (1) Remove the screws. (1) Remove the screws. Shooting direction: A Shooting direction: A X1300WE3 only x7 (2) Remove the CORD HOLDER and connectors.
REPAIR INFORMATION TROUBLE SHOOTING SPECIAL MODE 1. POWER Special mode setting button AVR-X1300W 2. Analog video Special mode setting button AVR-S720W 3. HDMI/DVI 1. Version Display Mode 4. AUDIO 2. PANEL / REMOTE LOCK Selection Mode 5. Network / Bluetooth / USB 3-1.
Page 61
TROUBLE SHOOTING 1. POWER 1.1. The unit does not power on 1.2. Fuse is blown The unit does not power on Blown fuse Does the power indicator on the front panel Does the power indicator on the front Check the rectifier diode in the Check for short circuits between flash in green or white when the power is turned panel flash in red when the power is turned...
Page 62
2. Analog video MONITOR OUT (CVBS) output NG Is the power voltage being output correctly? +5VV :C8812 : + side The power supply circuit is faulty. -5VV :C8813 : - side Check the pattern between JK881 and IC881, Is a signal being output from the video ampli- Does the signal input to the video amplifier? and then check the Blu-ray/DVD player or the fier?
Page 63
3. HDMI/DVI 3.1. No picture or sound is output (HDMI to HDMI) (8) When using a DENON Blu-ray/DVD player, is the "HDMI" indicator of the fluorescent display lit? Proceed to YES when using a Blu-ray/DVD player produced by other manufactures.
Page 64
(15) Are a picture and sound output when a dif- The TV is faulty. ferent TV is used? Check the unit. "HDMI "Rx/Tx" Failure Detection".
4. AUDIO 4.1. AUDIO CHECK No audio output CHECK 1 INPUT SURROUND MODE SOURCE Check the ANALOG AUDIO BLOCK Audio output OK? ANALOG 2CH DIRECT ANALOG CHECK 2 INPUT SURROUND MODE SOURCE Check the DIGITAL AUDIO BLOCK Legacy Audio output OK? COAX or OPT (PCM or DolbyDigital or dts…) CHECK 3...
Page 66
4.2. Power AMP (AMP PCB) 4.3. Analog audio No audio output. No audio output. Protection is activated. Is the power transistor open or short circuited? Is a voltage of ± 12 V supplied to DIGITAL PCB Replace the power transistor. Repair the ±...
Page 67
5. Network / Bluetooth / USB 5.1. Cannot connect to the network Check the connection environment Can the D3.3V output voltage The circuit of D5V_POWER Insert the LAN cable correctly and then turn on Is D5V_POWER (IC751 uCOM Is the LAN cable correctly inserted? (3.3V) to IC741 (DC-DC Conv.) between IC751 and IC741 are the power again.
Page 68
5.2. Cannot establish a Bluetooth connection Can the NET2.5V output volt- The circuit of E_POWER2 Is E_POWER2 (IC751 uCOM 55 age (2.5 V) to IC742 (DC-DC between IC751 and IC741 are pin) "Hi" ? Check the Bluetooth device being used Conv.) be confirmed? faulty.
Page 69
5.3. Cannot recognize the connected USB device Check the USB device being used Is a USB hub being used? Do not use a USB hub. This unit supports devices in the FAT16- and FAT32-formatted mass storage class, MTP- Is the USB device supported by this unit? compatible devices and iPod devices (except for some models).
Page 71
6. SMPS Operation waveform for each part DC5.2V is not output. Primary drain After primary side rectification (Caution: High voltage, electric shock) (Caution: High voltage, electric shock) OPTION C6002 250V/0.01uF *OPTION Replace the IC601(TOP268VG) Is IC601(TOP268VG) dam- D6001 1N4007 After secondary rectifications and D6001/ D6002 / D6003 / D6002 1N4007 aged?
Page 72
HDMI "Rx/Tx" Failure Detection 1. Prior checking Check item (0) : Checking the HDMI connector Checking the condition of the HDMI pin (rear/front). There are deformed pins. Replace the HDMI connector. Check for deformed pins. None of the pins are deformed. 3.
Page 73
Port: Select COM port of PC Baud rate: 19200bps Data bits: 8 Stop bits: 1 Parity: none Transmitted text Flow control: none Select Append CR-LF Forward: (none) Check the Local Echo check box. Figure 1-1 Device Connection Method (AVR-X1300W/S720W) Figure 3 Serial Port Setup Screen...
Page 74
1. Input a command in the 2.Click on the transmission button. transmission command input. Press Press Figure 6-1. AVR settings (AVR-X1300W) Figure 6-2. AVR settings (AVR-S720W) Figure 8 Method for Sending Termite Commands All the for Volume 7 segment indicator Lights...
Page 75
3. Starting detecting the point of failure 3-1 Check the "HDMI/DVI" item in troubleshooting. Check item(1). Check that the version of the AVR can be read After rewriting the GUI ROM, check the GUI ver- correctly. sion. Is the GUI version readable correctly? If it does not work, replace the GUI Rom(IC732) and recheck the GUI Ver.
Page 76
3-2 HDMI Rx/Tx MN864788)failure detection procedure Checking HDMI (HDMI Rx/Tx) device When the results of check item (5) are "the communication results are not OK" Check communication between CPU and the HDMI Rx/Tx device. Checking (HDMI Rx/Tx) device. Check item (5). : Check communication between CPU and the HDMI Example : Check the power supply voltage.
Page 77
Checking the reset waveform (HDMI Rx/Tx) Check item(8). Checking the reset waveform : Check the waveform. Is the "I2C" waveform of the TP near the HDMI Rx (IC721 115pin) Checking the HDMI Rx/Tx. Checking the HDMI SW. correct (like the one shown in the diagram) when the power is Remove the damping resistor Remove the damping resistor turned on?
Page 78
When the results of check item (5) are "the communication results are OK" Checking operation between the HDMI (Rx/Tx) device and the player Check item(12). Checking the +5V/DDC status register : Example Send the following command from Termite.exe. When the HDMI IN4, Send the transmission command "i 0003 0054 b In order to check, connect the player to the HDMI terminal and configure the player as AVR source.
Page 79
When the results of check item (11) are "00" When the results of check item (12) are "00 or 04" (Detection of 5V is not OK) (Detection of DDC is not OK.) Checking +5 V voltage (HDMI Rx/Tx) Check the DDC line (HDMI Rx/Tx) Check item(13).
Page 80
When the results of check item (12) are "22" (Detection of DDC is OK.) Checking the TMDS status register 3.3V TMDS Signal TMDS Check item(15). Checking register of the TMDS CLK detection status Example register : Send the following command from Termite.exe. Example of waveform in check ①...
Page 81
3-3 HDMI SW(MN864788A) failure detection procedure Checking HDMI (HDMI SW) device When the results of check item (18) are "the communication results are not OK" Check communication between CPU and the HDMI (HDMI SW) device. Checking HDMI (HDMI SW) device. Check item (18).
Page 82
When the results of check item (18) are "the communication results are OK" Checking operation between the HDMI (HDMI SW) device and the player Check item(22). Checking the +5V/DDC status register : Example Send the following command from Termite.exe. HDMI IN When the HDMI IN1, Send the transmission command "i 002B 0084 0001"...
Page 83
When the results of check item (21) are "00" When the results of check item (22) are "00 or 04" (Detection of 5V is not OK) (Detection of DDC is not OK.) Checking +5 V voltage (HDMI SW) Check the DDC line (HDMI SW) Check item(23).
Page 84
When the results of check item (22) are "22" (Detection of DDC is OK.) Checking the TMDS status register (HDMI SW) 3.3V TMDS Signal TMDS Check item(25). Checking register of the TMDS CLK detection status Example register : Send the following command from Termite.exe. Example of waveform in check ①...
Page 85
3-4 Front HDMI Buffer IC (AD8195) failure detection procedure Checking operation between the HDMI (Front HDMI Buffer) and the player Checking the +5V/DDC status register (Front HDMI Buffer) Check item(31). Checking the 5 V status of the register : Example Send the following command from Termite.exe.
Page 86
When the results of check item (31) are "00" When the results of check item (32) are "00 or 04" (Detection of 5V is not OK.) (If the DDC are not OK) Checking +5 V voltage (Front HDMI Buffer) Checking DDC Line (Front HDMI Buffer) Check item(33).
Page 87
When the results of check item (32) are "22" (Detection of DDC is OK) Checking the TMDS status register Check item(35). Check the TMDS CLK detection status of the regis- Check item (36). Checking the TMDS input waveform. : Example ter.
Page 88
3-5 OSD(ADV7623) failure detection procedure Checking HDMI (OSD) device. When the results of check item (37) are "the communication results are not OK" Check the I2C communication. Checking HDMI (OSD) device. Check item (37). Check communication between CPU and the Example HDMI Tx device.
Page 89
Checking the reset waveform. Check the I2C communication line. Check item(40). Checking the reset. : Check item(41). Check the I2C communication line : Check the CPU. Check the CPU. Is the waveform of the TP near the OSD(IC731)97pin) correct (like Is the "I2C"...
Page 90
When the results of check item (46) are "the communication results are OK" Check the TMDS status of the register. (OSD -> HDMI Rx/Tx) Check item(43). Check the TMDS CLK detection status of the regis- Check item (44). Checking the TMDS input waveform. : Example ter.
Page 91
Check the connection between the HDMI OUT terminal and the TV. Connect the HDMI OUT terminal and the TV, and then turn on the TV and check the following items. Check the HPD and RXSENSE register value of the HDMI TX device (Monitor). Check item(45).
Page 92
When the results of check item (45) are "30" (Detection of HPD is OK / Detection of RXSENSE is OK ) Example Checking the EDID register (Monitor) Check item(46). Check the Monitor EDID : ① Unplug the AC cord. Plug the AC cord into a power outlet. ②...
Page 93
When the results of check item (45) are "10" When the results of check item (45) are "20" (Detection of HPD is OK / Detection of RXSENSE is not OK ) (Detection of HPD is not OK / Detection of RXSENSE is OK ) Checking the RXSENSE (Monitor) Checking the HPD.
Page 94
When the results of check item (45) are "00" (Detection of HPD is not OK / Detection of RXSENSE is not OK ) Checking the RXSENSE/HPD. (Monitor) Check item(51). Checking the HPD and RXSENSE. : Does the test point of RXSENSE close to the HDMI output terminal (JK751) indicate the 3.3 V? Does the voltage of HPD test point close to the HDMI output terminal (JK751) indicate Hi (3-5 V)?
Page 95
3-6 HDMI Rx/Tx(MN864788) & OSD(ADV7623) failure detection procedure HDMI IN1 HDMI OUT ※ In order to check, connect the player and the TV to the HDMI terminal and configure as AVR source. Check sound output by turning on the player and the TV. Checking the TMDS status of the register.
CLOCK FLOW & WAVE FORM IN DIGITAL BLOCK WAVE FORM (1)DIRIN SPDIF (1) SPDIF input ADINL ADINR DIG TAL IN O PEN DIR_CE DAC_M UTE DIR_CLK DAC_RST M CLK1 O PT1(TV) DIR_DIN DAC_M S 256FSDIR1 DIR_DO UT DAC_DATA 64FSDIR1 DIR_RST DAC_CLK CH1:SPDIF FSDIR1...
(See 3-4. TUNER STEP mode (E2 / E3 only)) If there are multiple DENON AV receivers in the same area, this mode prevents other AV receivers from being operated concur- 3-5 Remote ID Setup Mode rently with this device. ↑...
Page 99
(See 3-4. TUNER STEP mode (E2 / E3 only)) If there are multiple DENON AV receivers in the same area, this mode prevents other AV receivers from being operated concur- 3-5 Remote ID Setup Mode rently with this device. ↑...
Page 100
GUI SFLASH : Version information is displayed when the device is started in this mode. :@@$\**** @ : Model code, $ : Brand code (DENON=1), 1.2. Starting up \ : Region code (E3=1, E2=2, E1C=5, JP=4, ALL=0), * : version While holding down buttons "DIMMER"...
Page 101
1.4. Error display See the table below for descriptions of the displayed errors and countermeasures for these. If multiple errors occur, only one item is displayed. The priority order is w, e, r, q. Condition States Display TROUBLE SHOOTING FIRM ERROR The model name, brand name and region information written in the firmware are compared to the region settings in the PCB.
Page 102
1.5. Version Display in the Setup Menu Follow the steps below to display the firmware information. (1) Press the "SETUP" button on the remote control. (2) Select "General - Information - Firmware". The version information is displayed as a 12-digit number as shown in the screen shot below. General/Firmware Version XXXX - XXXX - XXXX...
Page 103
2. PANEL / REMOTE LOCK Selection Mode 2.1. Actions Switch the PANEL LOCK and REMOTE LOCK modes between on and off. 2.2. Starting up While holding down buttons "TUNER PRESET CH+" and "ZONE2 SOURCE" simultaneously, press the power button to turn on the power. Select the desired mode using the "TUNER PRESET CH+"...
4.OP INFO clear mode. Operation Info for the unit can be checked. 3-1.2. Starting up AVR-X1300W · While holding down buttons "ZONE2 SOURCE", "DIMMER" and "STATUS" simultaneously, press the power button to turn on the power. 5.TUNER FRQ SET AVR-S720W ·...
Page 105
If the power is turned on in the abnormal state, protection is activated after around 90 seconds and the power is turned off. 3-2.2. Starting up AVR-X1300W Caution : These protections may also be activated due to other factors such as disconnection of connec- · While holding down buttons "ZONE2 SOURCE", "DIMMER" and "STATUS" simultaneously, press the tors or operations around the microcomputer.
Page 106
This is a special mode for enabling reception STEP of the ANALOG TUNER to be changed. tection count. 3-4.2. Starting up 3-3.2. Starting up AVR-X1300W AVR-X1300W · While holding down buttons "ZONE2 SOURCE", "DIMMER" and "STATUS" simultaneously, press the · While holding down buttons "ZONE2 SOURCE", "DIMMER" and "STATUS" simultaneously, press the power button to turn on the power.
Page 107
3-5. Remote ID Setup Mode 3-5.1. Actions This function allows only the desired AV receiver to be operated if multiple DENON AV receivers are used in the same room. 3-5.2. Starting up AVR-X1300W · While holding down buttons "ZONE2 SOURCE", "DIMMER" and "STATUS" simultaneously, press the power button to turn on the power.
Page 108
(2) Quick Select 4.2. Operations (3) Presets (4) Internet Radio Recently Played AVR-X1300W (5) Flickr contacts · While holding down buttons "TUNER PRESET CH +", "ZONE2 SOURCE" and "STATUS" simultane- (6) User ID ously, press the power button to turn on the power.
Remove all input/output terminals and the AC plug. Connect the AC plug again and place the product in standby mode. AVR-X1300W · While holding down buttons "ZONE2 SOURCE" and "STATUS" simultaneously, press the power but- ton to turn on the power.
Page 110
The Video and Audio paths can be checked. The backup data is not rewritten. 1.2. Starting up AVR-X1300W · While holding down buttons "ZONE2 SOURCE", "DIMMER" and "STATUS" simultaneously, press the power button to turn on the power. AVR-S720W · While holding down buttons "TUNER PRESET CH+", "TUNE -" and "TUNE +" simultaneously, press the power button to turn on the power.
Page 111
Paths to be confirmed Display Settings What to confirm Input Source : CBL/SAT ・ HDMI input ⇒ Speaker output (Front L/R) Input Mode : HDMI (fixed) ( b The input source can be switched to any source except CBL/SAT.) fig.04a Sound mode : STEREO 4 HDMI A05:HDMI...
DIAGNOSTIC PATH DIAGRAM fig.01 AVRS720W /X1300W ANALO G AUDIO BLO CK H/P O UT H/P L G ND H/P R P-AM P SPK O UT ANA_FL ANA01 DA_FL DA01 ANA_FR ANA02 DA_FR DA02 M AIN TUNER FM /AM DA_CEN DA03 32.768kHz AUDIO IN DA_SW...
Page 113
fig.02a AVRS720W /X1300W DIG ITAL AUDIO BLO CK ADINL ADINR DIG TAL IN O PEN DIR_CE DAC_M UTE DIR_CLK DAC_RST M CLK1 O PT1(TV) DIR_DIN DAC_M S 256FSDIR1 DIR_DO UT DAC_DATA 64FSDIR1 DIR_RST DAC_CLK O PT2(CBL/SAT) FSDIR1 O PT.1 SBCK O PT.2 SLRCK CO AX1(CBL/SAT)
Page 114
fig.02b AVRS720W /X1300W ANALO G AUDIO BLO CK H/P O UT H/P L G ND H/P R P-AM P SPK O UT ANA_FL ANA01 DA_FL DA01 ANA_FR ANA02 DA_FR DA02 M AIN TUNER FM /AM DA_CEN DA03 32.768kHz AUDIO IN DA_SW DA04 M EDIA PLAYER...
Page 115
fig.03a AVRS720W /X1300W DIG ITAL AUDIO BLO CK ADINL ADINR DIG TAL IN O PEN DIR_CE DAC_M UTE DIR_CLK DAC_RST M CLK1 O PT1(TV) DIR_DIN DAC_M S 256FSDIR1 DIR_DO UT DAC_DATA 64FSDIR1 DIR_RST DAC_CLK O PT2(CBL/SAT) FSDIR1 O PT.1 SBCK O PT.2 SLRCK CO AX1(CBL/SAT)
Page 116
fig.03b AVRS720W /X1300W ANALO G AUDIO BLO CK H/P O UT H/P L G ND H/P R P-AM P SPK O UT ANA_FL ANA01 DA_FL DA01 ANA_FR ANA02 DA_FR DA02 M AIN TUNER FM /AM DA_CEN DA03 32.768kHz AUDIO IN DA_SW DA04 M EDIA PLAYER...
Page 117
fig.04a AVRS720W /X1300W DIG ITAL AUDIO BLO CK ADINL ADINR DIG TAL IN O PEN DIR_CE DAC_M UTE DIR_CLK DAC_RST M CLK1 O PT1(TV) DIR_DIN DAC_M S 256FSDIR1 DIR_DO UT DAC_DATA 64FSDIR1 DIR_RST DAC_CLK O PT2(CBL/SAT) FSDIR1 O PT.1 SBCK O PT.2 SLRCK CO AX1(CBL/SAT)
Page 118
fig.04b AVRS720W /X1300W ANALO G AUDIO BLO CK H/P O UT H/P L G ND H/P R P-AM P SPK O UT ANA_FL ANA01 DA_FL DA01 ANA_FR ANA02 DA_FR DA02 M AIN TUNER FM /AM DA_CEN DA03 32.768kHz AUDIO IN DA_SW DA04 M EDIA PLAYER...
Page 119
fig.05a AVRS720W /X1300W DIG ITAL AUDIO BLO CK ADINL ADINR DIG TAL IN O PEN DIR_CE DAC_M UTE DIR_CLK DAC_RST M CLK1 O PT1(TV) DIR_DIN DAC_M S 256FSDIR1 DIR_DO UT DAC_DATA 64FSDIR1 DIR_RST DAC_CLK O PT2(CBL/SAT) FSDIR1 O PT.1 SBCK O PT.2 SLRCK CO AX1(CBL/SAT)
Page 120
fig.05b AVRS720W /X1300W ANALO G AUDIO BLO CK H/P O UT H/P L G ND H/P R P-AM P SPK O UT ANA_FL ANA01 DA_FL DA01 ANA_FR ANA02 DA_FR DA02 M AIN TUNER FM /AM DA_CEN DA03 32.768kHz AUDIO IN DA_SW DA04 M EDIA PLAYER...
Page 121
fig.06 AVRS720W /X1300W ANALO G AUDIO BLO CK H/P O UT H/P L G ND H/P R P-AM P SPK O UT ANA_FL ANA01 DA_FL DA01 ANA_FR ANA02 DA_FR DA02 M AIN TUNER FM /AM DA_CEN DA03 32.768kHz AUDIO IN DA_SW DA04 M EDIA PLAYER...
Page 122
fig.07 AVRS720W /X1300W VIDEO BLO CK ADV7623 HDM I RX(M N864788A) TRANSCEIVER P3 RX AD8195 F-HDM I IN6 Buffer (AUX) 28.6363M Hz O SD Block P2 RX HDM I IN1 (CBL/SAT) P1 TX P1 RX HDM I IN2 (DVD/BLU-RAY) O THER : 32M S.FLASH E2 : 64M 32M /64M...
Page 123
fig.08 AVRS720W /X1300W VIDEO BLO CK ADV7623 HDM I RX(M N864788A) TRANSCEIVER P3 RX AD8195 F-HDM I IN6 Buffer (AUX) 28.6363M Hz O SD Block P2 RX HDM I IN1 (CBL/SAT) P1 TX P1 RX HDM I IN2 (DVD/BLU-RAY) O THER : 32M S.FLASH E2 : 64M 32M /64M...
Page 124
fig.09 AVRS720W /X1300W VIDEO BLO CK ADV7623 HDM I RX(M N864788A) TRANSCEIVER P3 RX AD8195 F-HDM I IN6 Buffer (AUX) 28.6363M Hz O SD Block P2 RX HDM I IN1 (CBL/SAT) P1 TX P1 RX HDM I IN2 (DVD/BLU-RAY) O THER : 32M S.FLASH E2 : 64M 32M /64M...
Page 125
fig.10 AVRS720W /X1300W DIG ITAL AUDIO BLO CK ADINL ADINR DIG TAL IN O PEN DIR_CE DAC_M UTE DIR_CLK DAC_RST M CLK1 O PT1(TV) DIR_DIN DAC_M S 256FSDIR1 DIR_DO UT DAC_DATA 64FSDIR1 DIR_RST DAC_CLK O PT2(CBL/SAT) FSDIR1 O PT.1 SBCK O PT.2 SLRCK CO AX1(CBL/SAT)
Page 126
fig.11 AVRS720W /X1300W VIDEO BLO CK ADV7623 HDM I RX(M N864788A) TRANSCEIVER P3 RX AD8195 F-HDM I IN6 Buffer (AUX) 28.6363M Hz O SD Block P2 RX HDM I IN1 (CBL/SAT) P1 TX P1 RX HDM I IN2 (DVD/BLU-RAY) O THER : 32M S.FLASH E2 : 64M 32M /64M...
JIG FOR SERVICING Use the following jigs (extension cable kit) when repairing the PCBs. (3) Remove the DIGITAL PCB from the chassis and turn it over. Order with your dealer for the jigs your dealer if necessary. Place an insulation sheet larger than the PCB underneath the DIGITAL PCB. b Connect the earth of the PCB to the chassis using an earth wire, etc.
Page 128
ADJUSTMENT Adjusting Idling Current 1. Preparation (1) Prepare a DC voltmeter. (2) Place the unit under normal usage conditions, away from highly ventilated areas such as next to an air conditioning machine or electric fan. The set requires an ambient temperature of 15℃ to 30℃ and standard humidity. (3) Settings of This Unit •...
Page 129
UPDATING PROCEDURE AFTER REPLACING THE PCB. PROCEDURE AFTER REPLACING THE U-COM, ETC. FIRMWARE UPDATE PROCEDURE 1. Items necessary for update 2. Updating via USB 3. Updating via DPMS...
Page 130
PROCEDURE AFTER REPLACING THE PCB. PROCEDURE AFTER REPLACING THE U-COM, ETC. The procedure after replacing the printed circuit boards is as follows. The procedure after replacing the u-COM (microprocessor), flash ROM, etc. is as follows. (1) Change the resistor for setting the region. Procedure PCB Name Ref.
FIRMWARE UPDATE PROCEDURE 1. Items necessary for update Items necessary for update are as follows. Offered / not Offered Update Type Needed Part for Update Requirement Standard Service Equipment Purchase from D&M Article code Download from SDI Not offered by D&M Via USB USB Stick (USB 2.0 : Min 1GB) Formatting FAT 32...
Page 132
2. Updating via USB The latest firmware can be downloaded to a USB memory for updates. 2.1. Connecting to the USB Memory (1) Preparation • Use a memory that supports USB2.0. • USB format : Prepare a USB memory formatted in FAT16 or FAT32. •...
Page 133
2.3. File structure on USB Memory 2.5. Start the update. Copy the update files to the USB memory with the following structure. AVR-X1300W · While holding down buttons "TUNER PRESET CH +" and "STATUS" simultaneously, press the USB memory root power button to turn on the power.
Page 134
DIGITAL PCB or the CY920. 2.9.2. Operations 2.10.2. Operations AVR-X1300W (1) Remove the AC power plug and turn off the power. · While holding down buttons the "TUNER PRESET CH +" and "STATUS" buttons simultaneously, (2) Copy the update file to a USB memory device and insert the USB memory device in the USB port.
Page 135
2.11. About the error codes Error USB Update Error Details of Error code Remedies Code Display See the table below for error codes and details of faults when the firmware is updated through USB memory. Update Error**09 Time Out while obtaining Unplug and reconnect the AC plug, and The error code is displayed as four digits made up of the Device ID below together with **YY ( ** : De- Firmware information.
Page 136
Error USB Update Error Error USB Update Error Details of Error code Remedies Details of Error code Remedies Code Display Code Display Failed to obtain the entire Reinsert or try a new USB device, Un- Try a new USB device, Unplug and Firmware information after Update Error**50 Unable to detect USB.
Page 137
Error USB Update Error Error USB Update Error Details of Error code Remedies Details of Error code Remedies Code Display Code Display Unplug and reconnect the AC plug, and Reinsert or try a new USB device, Un- NACK received in response or try again.
Page 138
3. Updating via DPMS Download the latest firmware from our website and update the firmware. 3.1. Network Connection (1) System Requirements • Internet Connection by Broadband Circuit • Modem • Router • Ethernet cable (CAT-5 or greater is recommended) (2) Setting Internet Computer Modem...
Page 139
3.3. About the error codes Error DPMS Update Error Details of Error code Remedies Code Display See the following table for details on the error code display, details of the error code, remedies when updating the firmware via DPMS. (DPMS : D&M Product Management Server) Error(NG) notification received Check the network connection, Unplug The error code is displayed as four digits made up of the Device ID below together with **YY ( ** : De-...
Page 140
Error DPMS Update Error Error DPMS Update Error Details of Error code Remedies Details of Error code Remedies Code Display Code Display Check the network connection, Unplug Error notification received Check the network connection, Unplug Update Error**24 DPMS connection failure and reconnect the AC plug, and try while requesting the Firm- and reconnect the AC plug, and try...
Page 141
Error DPMS Update Error Error DPMS Update Error Details of Error code Remedies Details of Error code Remedies Code Display Code Display Failed to start up Sub in Unplug and reconnect the AC plug, and Update Error**A7 Time Out while obtaining Unplug and reconnect the AC plug, and Power On sequence during Update Error**62...
Page 142
Copyright 2016 D&M Holdings Inc. All rights reserved.
Page 143
FRONT FRONT PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. Part indicated by "@" mark is not illustrated in the exploded view ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations.
Page 144
FRONT REF No. Part No. Part Name Remarks Q'ty New Ver R1409 RES,CHIP(1608/5%/100ohm) CRJ10DJ101T R1410 RES,CHIP(1608/5%/47Kohm) CRJ10DJ473T R1411 RES,CHIP(1608/5%/2.2Kohm) CRJ10DJ222T R1413 RES,CHIP(1608/5%/10Kohm) CRJ10DJ103T R1414 RES,CHIP(1608/5%/10Kohm) CRJ10DJ103T R1415 RES,CHIP(1608/5%/1Kohm) CRJ10DJ102T R1416 RES,CHIP(1608/5%/1Kohm) CRJ10DJ102T R1418 RES,CHIP(1608/5%/390ohm) CRJ10DJ391T R1419 RES,CHIP(1608/5%/390ohm) CRJ10DJ391T R1420 RES,CHIP(1608/5%/47Kohm) CRJ10DJ473T R1423 RES,CARBON(1/5W,47Kohm,J)
Page 145
FRONT REF No. Part No. Part Name Remarks Q'ty New Ver SW110 00D9430004402 SW,TACT CST1A012ZT SW111 00D9430004402 SW,TACT CST1A012ZT SW112 00D9430004402 SW,TACT S720 CST1A012ZT SW113 00D9430004402 SW,TACT S720 CST1A012ZT SW114 00D9430004402 SW,TACT S720 CST1A012ZT SW115 00D9430004402 SW,TACT CST1A012ZT SW116 00D9430004402 SW,TACT CST1A012ZT SW117...
Page 146
F-HDMI F-HDMI PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. Part indicated by "@" mark is not illustrated in the exploded view ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations.
Page 147
DIFF-AMP DIFF-AMP PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. Part indicated by "@" mark is not illustrated in the exploded view ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations.
Page 148
DIFF-AMP REF No. Part No. Part Name Remarks Q'ty New Ver C2206 CAP,CERAMIC(50V/33pF/J) CCCT1H330JC C2301 CAP,ELECT(50V/47uF) CCEA1HH470T C2302 CAP,MYLAR(100V/470pF/J) HCQI2A471JZT C2303 CAP,CERAMIC(50V/82pF/J) CCCT1H820JC C2304 CAP,MYLAR(50V/2200pF/J) HCQI1H222JZT C2305 CAP,ELECT(50V/220uF) CCEA1HH221T C2306 CAP,CERAMIC(50V/33pF/J) CCCT1H330JC C2401 CAP,ELECT(50V/47uF) CCEA1HH470T C2402 CAP,MYLAR(100V/470pF/J) HCQI2A471JZT C2403 CAP,CERAMIC(50V/82pF/J) CCCT1H820JC C2404 CAP,MYLAR(50V/2200pF/J)
Page 149
MAIN MAIN PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. Part indicated by "@" mark is not illustrated in the exploded view ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations.
Page 150
MAIN REF No. Part No. Part Name Remarks Q'ty New Ver R5233 RES,M-OXIDEFILM(2W/10ohm) CRG2SANJ100RT R5313 RES,CARBON(1/5W,2.7Kohm,J) CRD20TJ272T R5314 RES,CARBON(1/5W,560ohm,J) CRD20TJ561T R5315 RES,M-OXIDEFILM(1W/5.6Kohm) CRG1SANJ562RT R5316 RES,M-OXIDEFILM(1W/5.6Kohm) CRG1SANJ562RT R5317 RES,M-OXIDEFILM(1W/4.7ohm) CRG1SANJ4R7RT R5318 RES,M-OXIDEFILM(1W/4.7ohm) CRG1SANJ4R7RT R5319 943124500050S RES,M-OXIDEFILM(2W/0.47ohm) CRG2SANJR47RT R5320 943124500050S RES,M-OXIDEFILM(2W/0.47ohm) CRG2SANJR47RT R5321 943124500050S RES,M-OXIDEFILM(2W/0.47ohm)
Page 151
MAIN REF No. Part No. Part Name Remarks Q'ty New Ver R5817 RES,CARBON(1/5W,470Kohm,J) CRD20TJ474T R5818 RES,CARBON(1/5W,470Kohm,J) CRD20TJ474T R5819 RES,M-OXIDEFILM(1W/100ohm) CRG1SANJ101RT R5820 RES,M-OXIDEFILM(1W/33ohm) CRG1SANJ330RT R5821 RES,M-OXIDEFILM(1W/2.2Kohm) CRG1SANJ222RT R5823 RES,M-OXIDEFILM(1W/2.2Kohm) CRG1SANJ222RT R5824 RES,M-OXIDEFILM(1W/2.2Kohm) CRG1SANJ222RT R5827 943129501040S RES,CEMENT(5W,0.01OHM,5%SMALLSIZE) CRF5EJR01HS R5830 RES,CHIP(1608/5%/100ohm) CRJ10DJ101T R5831 RES,CHIP(1608/5%/10Kohm) CRJ10DJ103T R5832...
Page 152
MAIN REF No. Part No. Part Name Remarks Q'ty New Ver JK505 943643102420S 2P,SCREWSPK(R/B) CJJ5N023Z JK506 943643102420S 2P,SCREWSPK(R/B) CJJ5N023Z JK507 943643102420S 2P,SCREWSPK(R/B) CJJ5N023Z L5101 943115100310S COIL,SPEAKER(0.5UH) CLEY0R5KAD L5201 943115100310S COIL,SPEAKER(0.5UH) CLEY0R5KAD L5301 943115100310S COIL,SPEAKER(0.5UH) CLEY0R5KAD L5401 943115100310S COIL,SPEAKER(0.5UH) CLEY0R5KAD L5501 943115100310S COIL,SPEAKER(0.5UH) CLEY0R5KAD...
POWER POWER PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. Part indicated by "@" mark is not illustrated in the exploded view. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations.
Page 154
POWER REF No. Part No. Part Name Remarks Q'ty New C6030 CAP,CHIP(1608,50V/0.015uF,X7R)_SAMSUNG CCUS1H153KCS OTHER PARTS GROUP BK301 BRACKET,PCB CMD1A569-V1 BK302 BRACKET,PCB CMD1A569-V1 BK303 BRACKET,PCB CMD1A387-V1 BK601 BRACKET,PCBM3 CMD1A834 BK602 BRACKET,PCBM3 CMD1A834 BK603 BRACKET,PCB CMD1A629 BN301 WIREASS'YLocking(YH,5P,2.0MM,80MM,#24) CWB1C005080HC BN302 WIRE ASS'Y Locking (YH) (3P,2MM,50MM,#28) CWB1A003050HC BN601 WIREASS'Y(YH,6P,2.5MM,130MM,#22,H/STUBE)
Page 155
DIGITAL DIGITAL PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. Part indicated by "@" mark is not illustrated in the exploded view ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations.
Page 156
DIGITAL REF No. Part No. Part Name Remarks Q'ty New Ver Q7424 963212500030S T.R,ISA1530AC1 CVTISA1530AC1 Q7501 943214500030S T.R,MUTE CVTINC2001AC1 Q7502 943214500020S T.R,2SC3052 CVT2SC3052 Q7503 943214500020S T.R,2SC3052 CVT2SC3052 Q7601 943216500020S T.R,RT1N141C(10K-10K) CVTRT1N141C Q7602 943216500020S T.R,RT1N141C(10K-10K) CVTRT1N141C Q7603 943216500020S T.R,RT1N141C(10K-10K) CVTRT1N141C Q7604 943216500020S T.R,RT1N141C(10K-10K) CVTRT1N141C...
Page 157
DIGITAL REF No. Part No. Part Name Remarks Q'ty New Ver R7304 RES,CHIP(1005/5%/10Kohm) CRJ06IJ103T R7305 RES,CHIP(1005/5%/10Kohm) CRJ06IJ103T R7306 RES,CHIP(1005/5%/47Kohm) CRJ06IJ473T R7308 RES,CHIP(1005/5%/47Kohm) CRJ06IJ473T R7310 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R7311 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R7312 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R7314 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R7315 RES,CHIP(1005/5%/10Kohm) CRJ06IJ103T R7316 RES,CHIP(1005/5%/10Kohm) CRJ06IJ103T R7317 RES,CHIP(1005/5%/10Kohm)
Page 158
DIGITAL REF No. Part No. Part Name Remarks Q'ty New Ver R7514 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R7515 RES,CHIP(1005/5%/0ohm) CRJ06IJ0R0T R7516 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R7517 RES,CHIP(1608/5%/33ohm) CRJ10DJ330T R7518 RES,CHIP(1608/5%/33ohm) CRJ10DJ330T R7519 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R7520 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R7521 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R7522 RES,CHIP(1608/5%/33ohm) CRJ10DJ330T R7523 RES,CHIP(1608/5%/33ohm) CRJ10DJ330T R7524 RES,CHIP(1005/5%/10Kohm)
Page 159
DIGITAL REF No. Part No. Part Name Remarks Q'ty New Ver R7729 RES,CHIP(1608/5%/680ohm) CRJ10DJ681T R7730 RES,CHIP(1608/5%/100ohm) CRJ10DJ101T R7731 RES,CHIP(1608/5%/100ohm) CRJ10DJ101T R7738 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R7739 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R7751 RES,CHIP(1005/5%/100ohm) CRJ06IJ101T R7752 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R7753 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R7754 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R7755 RES,CHIP(1005/5%/100ohm) CRJ06IJ101T R7756 RES,CHIP(1005/5%/33ohm)
Page 160
DIGITAL REF No. Part No. Part Name Remarks Q'ty New Ver R7946 RES,CHIP(1608/5%/1Kohm) CRJ10DJ102T R7947 RES,CHIP(1608/0.5%/39Kohm) CRJ06DD393TP R7948 RES,CHIP(1608/5%/120Kohm) CRJ10DJ124T R7949 RES,CHIP(1608/5%/100ohm) CRJ10DJ101T R7951 RES,CHIP(1608/0.5%/15Kohm) CRJ06DD153TP R7952 RES,CHIP(1608/0.5%/15Kohm) CRJ06DD153TP R7953 RES,CHIP(1608/5%/150Kohm) CRJ10DJ154T R7954 RES,CHIP(1608/0.5%/12Kohm) CRJ06DD123TP R7955 RES,CHIP(1608/5%/470ohm) CRJ10DJ471T R7956 RES,CHIP(1608/5%/150Kohm) CRJ10DJ154T R7957 RES,CHIP(1608/0.5%/12Kohm)
Page 161
DIGITAL REF No. Part No. Part Name Remarks Q'ty New Ver R8246 RES,CHIP(1608/5%/100Kohm) CRJ10DJ104T R8247 RES,CHIP(1608/5%/100Kohm) CRJ10DJ104T R8248 RES,CHIP(1608/5%/100Kohm) CRJ10DJ104T R8249 RES,CHIP(1608/5%/100Kohm) CRJ10DJ104T R8250 RES,CHIP(1608/5%/100Kohm) CRJ10DJ104T R8251 RES,CHIP(1608/5%/100Kohm) CRJ10DJ104T R8252 RES,CHIP(1608/5%/100Kohm) CRJ10DJ104T R8253 RES,CHIP(1608/5%/100Kohm) CRJ10DJ104T R8254 RES,CHIP(1608/5%/100Kohm) CRJ10DJ104T R8255 RES,CHIP(1608/5%/820ohm) CRJ10DJ821T R8256 RES,CHIP(1608/5%/0ohm)
Page 162
DIGITAL REF No. Part No. Part Name Remarks Q'ty New Ver C7125 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C7126 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C7127 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C7128 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C7129 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C7130 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C7131 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C7136 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C7137 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C7138 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C7139 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG...
Page 163
DIGITAL REF No. Part No. Part Name Remarks Q'ty New Ver C7307 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C7308 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C7309 CAP,ELECT(10V/100uF) CCEA1AH101T C7310 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C7311 CAP,CHIP(2012,6.3V/10uF,X5R)_SAMSUNG CCUC0J106KCS C7312 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C7313 CAP,CHIP(2012,6.3V/10uF,X5R)_SAMSUNG CCUC0J106KCS C7314 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C7315 CAP,CHIP(2012,6.3V/10uF,X5R)_SAMSUNG CCUC0J106KCS C7318 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C7319 CAP,CHIP(1608,10V/1uF,X7R,X7S)_SAMSUNG...
Page 164
DIGITAL REF No. Part No. Part Name Remarks Q'ty New Ver C7492 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C7493 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C7494 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C7495 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C7496 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C7497 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C7498 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C7499 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C7500 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C7501 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C7502 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG...
Page 165
DIGITAL REF No. Part No. Part Name Remarks Q'ty New Ver C7906 943134502350S CAP,ELECT(50V/470uF) CCEA1HH471E C7907 CAP,CHIP(1608,10V/1uF,X7R,X7S)_SAMSUNG CCUS1A105KCS C7908 CAP,CHIP(1608,50V/0.1uF,X7R)_SAMSUNG CCUS1H104KCS C7909 CAP,CHIP(1608,50V/0.1uF,X7R)_SAMSUNG CCUS1H104KCS C7910 CAP,CHIP(1608,50V/0.1uF,X7R)_SAMSUNG CCUS1H104KCS C7911 CAP,CHIP(1608,50V/1800pF,X7R)_SAMSUNG CCUS1H182KCS C7913 CAP,CHIP(1608,50V/270pF,C0G)_SAMSUNG CCUS1H271JAS C7914 CAP,CHIP(1608,50V/270pF,C0G)_SAMSUNG CCUS1H271JAS C7916 CAP,ELECT(63V/100uF) CCEA1JH101E C7921 CAP,CHIP(1608,50V/1800pF,X7R)_SAMSUNG CCUS1H182KCS C7923...
Page 166
DIGITAL REF No. Part No. Part Name Remarks Q'ty New Ver C8255 CAP,CHIP(1608,50V/0.1uF,X7R)_SAMSUNG CCUS1H104KCS C8256 CAP,CHIP(1608,50V/0.1uF,X7R)_SAMSUNG CCUS1H104KCS C8257 CAP,CHIP(1608,50V/0.1uF,X7R)_SAMSUNG CCUS1H104KCS C8258 CAP,CHIP(1608,50V/0.1uF,X7R)_SAMSUNG CCUS1H104KCS C8259 CAP,ELECT(50V/10uF) CCEA1HH100T C8260 CAP,CHIP(1608,50V/0.1uF,X7R)_SAMSUNG CCUS1H104KCS C8261 CAP,CHIP(1608,50V/0.1uF,X7R)_SAMSUNG CCUS1H104KCS C8262 CAP,ELECT(50V/0.1uF) CCEA1HH0R1T C8263 CAP,ELECT(50V/22uF) CCEA1HH220T C8264 CAP,ELECT(50V/22uF) CCEA1HH220T C8265 CAP,CHIP(1608,50V/330pF,C0G)_SAMSUNG...
Page 167
DIGITAL REF No. Part No. Part Name Remarks Q'ty New Ver L7434 FERRITECHIPBEAD(2012/220R,CB05YTYH221) CLZ9R018V L7441 FERRITECHIPBEAD(1608/60R,CB03YTYH600) CLZ9R005V L7444 FERRITECHIPBEAD(2012/220R,CB05YTYH221) CLZ9R018V L7451 FERRITECHIPBEAD(1608/60R,CB03YTYH600) CLZ9R005V L7453 RES,CHIP(1608/5%/0ohm) CRJ10DJ0R0T L7471 FERRITECHIPBEAD(1608/60R,CB03YTYH600) CLZ9R005V L7473 RES,CHIP(1608/5%/0ohm) CRJ10DJ0R0T L7483 FERRITECHIPBEAD(1608/60R,CB03YTYH600) CLZ9R005V L7484 COIL,SMD5040,3.6uH CLQ28E3R6NRH L7485 COIL,SMD5040,3.6uH CLQ28E3R6NRH L7486 COIL,SMD(2.2uH,4.6A5040,50X40)
Page 169
PACKING PACKING ※Parts indicated by "nsp"on this table cannot be supplied. Part indicated by "@" mark is not illustrated in the exploded view ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations.
Need help?
Do you have a question about the AVR-X1300W and is the answer not in the manual?
Questions and answers
How many amps is the power fuze for the Denon avr x1300w bluetooth