Table of Contents
Advertisement
3- : Mechanism sensor information
[Common table of MN*, HD* and M3*]
Mechanism sensor information
Display
MN* / HD*
M3*
S-VHS SW
CASS SW
0-
VHS
Cassette insertion
1-
VHS
Cassette insertion
2-
VHS
Cassette insertion
3-
VHS
Cassette insertion
4-
VHS
Cassette insertion
5-
VHS
Cassette insertion
6-
VHS
Cassette insertion
7-
VHS
Cassette insertion
8-
S-VHS
Cassette ejection
9-
S-VHS
Cassette ejection
A-
S-VHS
Cassette ejection
B-
S-VHS
Cassette ejection
C-
S-VHS
Cassette ejection
D-
S-VHS
Cassette ejection
E-
S-VHS
Cassette ejection
F-
S-VHS
Cassette ejection
-4 : Mechanism mode position
[Common table of MN*, HD* and M3*]
Display
Mechanism mode position
MN* HD* M3*
-0
-7
-
Initial value
-1
-0
-
EJECT position
-
-
-0
EJECT position (Cassette housing drive mode)
-2
-7
-
Housing operating
-
-
-1
Between EJECT and U / L STOP
-3
-1
-2
U / L STOP position
-
-
-3
Guide arm drive position
-4
-7
-4
Tape being loaded / unloaded (When the pole base is
located on the front side of the position just beside the
drum)
-5
-2
-5
Tape being loaded / unloaded (When the pole base is
located on the rear side of the position just beside the
drum)
-6
-7
-6
Pole base compressed position
-7
-3
-F
FF / REW position
-8
-7
-F
Between FF / REW and STOP with pinch roller compres-
sion ON
-9
-4
-F
STOP with pinch roller compression OFF
-A
-7
-E
Between STOP with pinch roller compression OFF and
REV
-B
-5
-
REV (REV STILL / SLOW) position
-
-
-D
REV position
-
-
-C
Between REV and REV STILL / SLOW
-
-
-B
REV STILL / SLOW position
-C
-7
-
Between REV and FWD
-
-
-A
Between REV STILL / SLOW and FWD STILL / SLOW
-D
-6
-
FWD (FWD STILL / SLOW) position
-
-
-9
FWD STILL / SLOW position
-E
-7
-
Between FWD and PLAY
-
-
-8
Between FWD STILL / SLOW and PLAY
-F
-6
-7
PLAY position
Note:
• In the case of the "HD*" microprocessor, as the dis play
is always "-7" at any intermediate position between
modes, the position of transitory EMG may sometimes
not be located.
2.8.5 EMG detail information <2>
The type of the cas sette tape and the cassette tape winding po-
sition can be confirmed based on the figure in EMG detail infor-
mation<2>.
[FDP /OS D dis play]
*5 : *6 : *7
* 5 : Type of the cas sette tape in use <1>
* 6 : Winding pos ition of the cas sette tape in use
* 7 : Type of the cas sette tape in use <2> (Winding area)
Note:
• EMG detail information <2> is the reference informa-
tions tored using the remaining tape detection function
of the cassette tape. As a result, it may not identify cas-
sette correctly when a special cassette tape is used or
when the tape has variable thickness.
1-14 (No.82933)
REC safety
Start
End
SW
sensor
sensor
Tab broken
ON
ON
Tab broken
ON
OFF
Tab broken
OFF
ON
Tab broken
OFF
OFF
Tab present
ON
ON
Tab present
ON
OFF
Tab present
OFF
ON
Tab present
OFF
OFF
Tab broken
ON
ON
Tab broken
ON
OFF
Tab broken
OFF
ON
Tab broken
OFF
OFF
Tab present
ON
ON
Tab present
ON
OFF
Tab present
OFF
ON
Tab present
OFF
OFF
*5 : Cassette tape type <1>
Display
Cassette tape type <1>
00
Cassette type not identified
16
Large reel/small reel (T-0 to T-15/T-130 to T-210) not classified
82
Small reel, thick tape (T-120) identified/thin tape (T-140) identified
84
Large reel (T-0 to T-60) identified
92
Small reel, thick tape (T-130) identified/thin tape (T-160 to T-210) identified
93
Small reel, thick tape/C cassette (T-0 to T-100/C cassette) not classified
C3
Small reel, thick tape/C cassette (T-0 to T-100/C cassette) being classified
D3
Small reel, thick tape/C cassette (T-0 to T-100/C cassette) being classified
E1
C cassette, thick tape (TC-10 to TC-20) identified
E2
Small reel, thick tape (T-0 to T-100) identified
E9
C cassette, thin tape (TC-30 to TC-40) identified
F1
C cassette, thick tape/thin tape (TC-10 to TC-40) not classified
Notes:
• Cassette tape type <1> is identified a few times during
mode transition and the identification count is variable
depending on the cassette tape type. If an EMG occurs
in the middle of identification, the cassette tape type
may not be able to be identified.
• If other value than those listed in the above table is dis-
played, the cassette tape type is not identified.
*6 : Cassette tape winding position
The cassette tape winding position at the moment of EMG is dis-
played by dividing the entire tape (from the beginning to the end)
in 22 sections using a hex number from "00" to "15".
"00"
: End of winding
"15"
: Beginning of winding
"FF or - -" : Tape position not identified
*7 : Cassette tape type <2> (Winding area)
Display
00
Cassette type not identified
07
Small reel, thick tape
08 - 0E
C cassette, thick tape
09 - 15
C cassette, thick tape
0A - 0B
Small reel, thick tape
0A - 16
C cassette, thin tape
0A - 16
C cassette, thin tape
0D - 0F
Small reel, thick tape
11 - 14
Small reel, thick tape
15 - 18
Small reel, thick tape
17 - 1A
Small reel, thick tape
19 - 1D
Small reel, thick tape
1D - 21
Small reel, thick tape
1E - 1F
Small reel, thin tape
1F - 23
Small reel, thick tape
21 - 23
Small reel, thin tape
21 - 23
Small reel, thin tape
22 - 24
Small reel, thick tape
22 - 24
Small reel, thin tape
22 - 24
Small reel, thin tape
22 - 23
Large reel
23 - 24
Large reel
25 - 26
Large reel
27 - 29
Large reel
29 - 2B
Large reel
2D - 2F
Large reel
Note:
• The values of cassette tape type <2> in the above table
are typical values with representative cassette tapes.
2.8.6 EMG detail information <3>
Three deck operation modes preceding the deck operation mode
in which the EMG occurs may be confirmed based on the figures
in the EMG information detail <3>. For the contents of the dis-
played information, see the table "Deck operation mode" in sec-
tion "2.8.4 EMG detail information <1>".
Cassette tape type <2>
T-5
TC-10
TC-20P
T-20
TC-30
TC-40
T-40
T-60
T-80 / DF-160
T-90 / DF-180
T-100
T-120 / DF-240
T-140
T-130
T-160
T-168
DF-300
T-180 / DF-360
T-210 / DF-420
T-5
T-10
T-20
T-30
T-40
T-60
Advertisement
Table of Contents
