PPA SPIN Technical Manual
  1. Manuals
  2. Brands
  3. PPA Manuals
  4. Gate Opener
  5. SPIN
  6. Technical manual
PPA SPIN Technical Manual

PPA SPIN Technical Manual

Operator for social door pivoting
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Technical manual
SPIN
OPERATOR FOR
SOCIAL DOOR PIVOTING
ATTENTION:
Do not use the equipment
Manufactured by: Motoppar Indústria e Comércio de Automatizadores Ltda
without first reading the
Av. Dr. Labieno da Costa Machado, 3526 - Distrito Industrial - Garça - SP - CEP 17406-200 - Brasil
instruction manual.
CNPJ: 52.605.821/0001-55
P30194 - 03/2022
Rev. 0
www.ppa.com.br | +55 14 3407 1000

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SPIN and is the answer not in the manual?

Questions and answers

Related Manuals for PPA SPIN

Summary of Contents for PPA SPIN

  • Page 1 Manufactured by: Motoppar Indústria e Comércio de Automatizadores Ltda without first reading the Av. Dr. Labieno da Costa Machado, 3526 - Distrito Industrial - Garça - SP - CEP 17406-200 - Brasil instruction manual. CNPJ: 52.605.821/0001-55 P30194 - 03/2022 Rev. 0 www.ppa.com.br | +55 14 3407 1000...

  • Page 2: Table Of Contents

    Fixing the operator on the wall .................7 How to fix the guide to the door ................9 Photocell .........................10 Before using the SPIN SOCIAL DOOR OPERATOR, read and strictly Closing the operator cover ..................11 follow all instructions contained in this manual.

  • Page 3: Tools Required For Installation

    TOOLS REQUIRED FOR INSTALLATION CARE WITH THE ELECTRICAL INSTALLATION To avoid damage to the wiring, it is important that all conductors are correctly Below are some tools needed to install the operator: attached to the operator. The passage of the wiring must be done through conduits, passing internally through the base of the floor, ensuring that none of the wiring conductors is trapped and damaged.

  • Page 4: Technical Characteristics

    INSTALLATION AND FIXATION OF THE OPERATOR TECHNICAL CHARACTERISTICS PARAMETER AND TECHNICAL CHARACTERISTICS OPERATOR TYPE PIVOTING PIVOTING PIVOTING PIVOTING MODEL SINGLE-PHASE SINGLE-PHASE SINGLE-PHASE SINGLE-PHASE RATED VOLTAGE 220 V 220 V 127 V 127 - 220 V NOMINAL 60 Hz 50 Hz 60 Hz 60 Hz FREQUENCY...

  • Page 5: How To Fix The Guide To The Door

    If the door has an internal opening, fix the operator so that the drive arm is a little HOW TO FIX THE GUIDE TO THE DOOR above the top of the door leaf. After fixing the operator with the drive arm, fix the aluminum guide to the door so that the actuation arm does not go over the limit and does not come out outside the guide (fix the aluminum guide in the center of the door).

  • Page 6: Photocell

    After all connections and adjustments have been made, place the board cover, close the operator cover and secure it with 2 M5 x 10 screws. Then glue the PPA sticker, as shown in the figure. 30 cm SCREW S M5 X10 Precautions - Do not install the receiver unit facing directly towards the sun;...

  • Page 7: Maintenance

    MAINTENANCE Before any Maintenance, remove the power cable from the mains. DEFECTS, PROBABLE CAUSES AND CORRECTIONS Some DEFECTS, PROBABLE CAUSES AND CORRECTIONS will be mentioned, which may occur in your Operator, if Maintenance needs to occur. DEFECTS PROBABLE CAUSES CORRECTIONS -Dirt on the rail.

Table of Contents