Page 2
Foreword Thank you for choosing BYD ATTO 3. To better use and maintain your BYD ATTO 3, please read this manual carefully and keep it properly after reading. Special Instructions: BYD recommends that you choose genuine spare parts and use, maintain, and repair the vehicle properly in accordance with this manual.
Page 4
Model Overview BYD ATTO 3 is a new energy, new power, and pure electric passenger car. It is the kind of environmentally sustainable product that BYD is dedicated to making. It features a load-bearing body, front-to-rear longitudinal beam, and power battery pack integrated with the body to fully ensure the safety of the battery and entire vehicle.
ILLUSTRATION INDEX Child Protection Lock ........58 Seats ..........59 Exterior ..........10 Seat Information .......... 59 Dashboard Panel ......11 Front Seat Adjustment ........ 60 Center Console ......... 12 Folding in Rear Seats ........61 Door ..........13 Head Supports ..........61 Steering Wheel .........
Page 7
IN-CAR DEVICES Driving Safety Precautions ......95 Suggestions for Vehicle Use ....... 96 Air Conditioning System ....138 How to Save Energy and Prolong A/C Panel View ..........138 Vehicle Service Life ........97 A/C Operation Interface ......138 Carrying Luggage ......... 97 Function Definitions ........
Exterior Trunk Lock P54 Door P50 Trunk P97 Combination Light P165 Tools Delivered with the Vehicle P185 Opening the Hood P167 Rear Wiper P133 Refrigerant P167 Side Mirror P132 Brake Fluid P168 Home Portable AC Charging P84 Under Hood Power Distribution Box (PDB) P173 AC Charging Pile Charging P86 Charging Station DC Charging P87...
Door Opening Car Door with Interior Door Hood Handle P167 Handle P51 Electric Window Switches P71 Trunk Lock P54 Window Lock Button P72 Center Console Door Lock P72 Side Mirror P132...
•If a seat belt is damaged or enhance protection. The force limiter malfunctions, contact a BYD buffers the seat belt's restraint force on the authorized dealer or service provider occupant's body within a certain range, to for confirmation and handling.
Page 18
• Keeping a proper sitting posture, pull REMINDER the seat belt out so that it is diagonally across the chest. The belt should not go •In order to ensure the seat belt under the arm or across the back of the provides due protection and prevents neck.
Page 19
Particularly, be sure to position the lap belt portion of the seat belt as low across the hips as possible, to prevent •If any fault is found, contact a BYD serious injury. authorized dealer or service provider for confirmation and handling. Until •The back seat belts' fastening method...
Front Airbag Deployment Front Airbag Deployment • In moderate to severe frontal crashes, a sensor detects a sharp deceleration and sends a signal to the ECU to trigger the front airbags. • When there is a frontal crash, the seat belt secures the occupant's lower body and torso in place.
• When the ECU detects a moderate to • When a side impact occurs, generally severe front or side impact, and the only the airbag on the impacted side triggering conditions are met, the front deploys. center airbag deploys to protect the •...
Page 23
The vehicle's nose hits the ground when The vehicle goes under a truck or other going down a steep slope. large vehicle. One side of the vehicle is hit by another The tail of the vehicle is hit by another vehicle.
Page 24
The vehicle hits a wall or another vehicle The lateral side of the vehicle hits a diagonally. columnar object. Parts other than the passenger WARNING! compartment receive side impacts. •Airbags are developed to match specific car models. Any changes to suspension, tire sizes, bumpers, chassis and original equipment can adversely affect the airbag system.
Page 25
If any of the following events occurs, If any of the following events occurs, •Do not disassemble or repair the contact a BYD authorized dealer or service contact a BYD authorized dealer or service A-pillar trim, ceiling, B-pillar trim provider immediately.
• The warning light goes on, or flashes while driving. If a fault occurs, go to Child Restraint System a BYD authorized dealer or service (CRS) provider for inspection and repair as soon as possible. Select a suitable child restraint system for Select a suitable child restraint system for •...
Page 27
• The rear seats are equipped with tether strap anchorages on the back of the seat. REMINDER •BYD Auto recommends that children should use an appropriate child restraint system, and it is recommended that they are seated on a rear outboard seat.
Page 28
• The front passenger seat is equipped with a tether strap anchorage on the •BYD recommends installing the CRS back of the seat. using the ISOFIX anchorage points of the car.
Page 29
• Only use child seats that are can endanger life or lead to serious recommended by BYD, are universally personal injury. approved, or are semi-universal and where the vehicle model is included on...
Page 30
Front passenger seat Front Front passenger Group Child Weight Rear seat passenger front airbag front airbag activated deactivated up to 10 kg up to 13 kg Rear facing 9 to 18 kg Forward facing 9 to 18 kg 15 to 25 kg 22 to 36 kg Table definitions: u: universal...
Page 31
Front passenger seat Size class/ Child Seat Outer Center Front passenger Front passenger Group ISOFIX Orientation front airbag front airbag rear seat rear seat class activated deactivated E/R1 IL-SU IL-SU 0: up to 10 kg Rear facing E/R1 Rear facing D/R2 IL-SU IL-SU...
Anti-Theft System • The vehicle is powered on without using the keyless start function of the smart key. Anti-Theft System Anti-theft OFF Anti-theft OFF • The alarm can be stopped by the Anti-Theft System Anti-Theft System following methods: If the vehicle is in anti-theft mode, it will •...
• For a more detailed overview on data vehicle maintenance, the information processing, data protection and data can also be transmitted to BYD engineers subject rights, please read the current for quality assurance, product defect version of the privacy policy for the reports or customer claim verification.
Page 34
Other Other • BYD is not liable for any such services provided by any other party. Infotainment system • In such cases, obtain information • Depending on vehicle configuration, about data use from the provider of the data can be added to the infotainment respective online service.
Page 35
(e.g. data from the airbag control unit to clarify an accident). • If required by law BYD may also be obliged to disclose data upon government authority request, e.g. in the event of criminal offence investigation.
Instrument Cluster Instrument Cluster View LCD Instrument Cluster Time Total mileage Power meter Driving range Speedometer Gear status State of Charge (SOC) meter Drive mode information Outside temperature Energy regeneration information...
Instrument Cluster Indicators Discharge indicator Indicators and Warning Lights Rain and light sensor indicator Turn signals ACC standby status indicator (Gray)* Light position indicator ACC speed indicator High beam indicator ACC status indicator* Rear fog light indicator AVH standby indicator (White) OK indicator Cruise control indicator...
Page 39
Motor refrigerant Main alarm indicator overheating indicator Unfastened seat belt warning ESC OFF warning light light Airbag warning light ESC warning light Electronic Parking Brake Anti-lock Braking System (EPB) indicator (ABS) warning light Parking brake system Drive power limit warning warning light light Steering system warning...
Page 40
ABS warnings light up at the same time, immediately stop • If an electronic smart key matching the the vehicle safely and contact a BYD vehicle is inside and the power button is authorized dealer or service provider.
Page 41
•During operation, a warning light that temperature is too high. lights up briefly does not indicate If any of these cases occurs, contact a BYD that there is a problem. authorized dealer or service provider for •If the ESC warning light is still on inspection as soon as possible.
Page 42
• If this warning light turns yellow, it indicates that the headlight is faulty. In this Parking brake system warning light case, take the vehicle to a BYD authorized dealer or service provider for inspection. When the brake fluid level is low or the...
Page 43
In this case, contact a BYD authorized dealer or service provider for • If the steering wheel is frequently turned inspection as soon as possible.
Page 44
OK. It goes off if the power battery works normally. Later, if the system becomes faulty, this warning light goes on again. In this case, contact a BYD authorized dealer or service provider for inspection as soon as possible.
Page 45
Please check the on-board and reconnect the charging equipment. If charging system. the fault persists, contact a BYD authorized dealer or service provider. The vehicle may be disconnected from the Please check the data data network.
Page 46
BYD authorized dealer or service provider. The function of the ICC or LKS is limited. In The function of the ICC or LKS this case, park the vehicle, and contact a BYD is limited.* authorized dealer or service provider.
Check the smart key battery. If the battery needs to be replaced, contact a BYD authorized dealer or service provider. •If the smart key is lost, contact a BYD authorized dealer or service provider as soon as possible to prevent theft or accidents.
Page 50
If the key is lost or with the normal functioning of these needs to be copied, use the key number devices. to copy it at a BYD authorized dealer or service provider. •In addition to people with pacemakers or defibrillators, people using other...
In order to ensure vehicle safety, handle it with care. If it is lost, go to a BYD authorized dealer or service provider to get a newly configured card and block the lost one.
Page 52
Locking/Unlocking with Smart CAUTION •After removing the mechanical key, pull the main door handle to open • The wireless remote control function the door. is used to unlock or lock all doors at close range, and complete additional functions. Opening Car Door with Interior •...
Page 53
Raising/Lowering Windows with • When anti-theft mode is activated, if no door is opened within 30 seconds after Smart Key all doors have been unlocked with the smart key, they will lock automatically. • When the ignition switch is on OFF: •...
Page 54
Locking/Unlocking with NFC Key Card* • Hold the NFC card close to the NFC sign on the right side mirror. Locking doors: Locking doors: • When the ignition switch is OFF and doors are closed but not locked, hold the NFC card close to the NFC sign on the right side mirror to lock all doors.
Page 55
Locking/Unlocking Trunk Lid • When the trunk lid is open and the switch is pulled for more than a second, the lid closes automatically. The lid Using the smart key to open or close the Using the smart key to open or close the stops closing after the switch is released.
Page 56
Setting the trunk lid opening height* Setting the trunk lid opening height* • Stop the opening lid motion at the desired position. Press and hold the lid switch for at least 3 seconds to set lid height. There will be a beep to indicate that the height has been successfully set.
Page 57
• Press the Start/Stop button, and change WARNING the ignition switch from OK to OFF. Then, all doors are locked automatically. » Make sure to remove any ice or snow from the area before opening Locking and unlocking all doors Locking and unlocking all doors the trunk, otherwise the lid may concurrently...
4. Insert the mechanical key into the keyhole, turn it counterclockwise as far as it can go, return it to the initial position and pull it out. (For details, see "Locking/Unlocking with Mechanical Key" in this chapter.) Unlocking Unlocking 1. Remove the mechanical key from the smart key.
In this case, bring all •The smart key is being carried along smart keys to a BYD authorized dealer or with a communication device, such service provider for repair. as a two-way radio or mobile phone.
Seats Set the lever to this position marked (1). Then, passengers cannot open the rear doors from inside the vehicle. To open the Seat Information rear doors, use the exterior door handles. When the vehicle is moving, all passengers in the vehicle must fasten their seat belts, and rest their backs against upright backrests.
REMINDER CAUTION •After adjusting the seat backrest, •When the switch is released, the seat make sure it is locked into place. stops at its current position. Do not place anything under the seat that •Do not place anything under the may interfere with its adjustment.
Folding in Rear Seats • Flipping and lowering the backrest • Pull up the backrest drawstring. • Push the backrest forward or backward to flip it over. Flip forward until the backrest is in contact with the seat cushion, and flip it back to the backrest locking position (a locking sound is heard).
Steering Wheel Steering Wheel Switch Group Panoramic view* Call Screen mode Voice recognition Right Distance+* Mode Lever Roller Distance-* Instrument/Back Left...
Page 64
When the ignition switch is on OK, the Panoramic view* audio control switch is available. • Press this button to enable/disable Buttons on the left Buttons on the left panoramic mode. Buttons on the right Buttons on the right ACC switch* Roller •...
Page 65
• In USB/Bluetooth music/third-party Voice recognition music app mode: • Press this button to switch from the • Press the button to play the infotainment system screen to the voice previous track. recognition screen. • Press the button to select a •...
Switches Steering Wheel Manual Adjustment Light Switches To adjust steering wheel angle: • Press the steering wheel adjustment Rotate the rotary knob to to turn off handle, move the steering wheel to the all lights except DRLs. desired angle, or adjust it to the desired axial position, and restore the handle to the locked position.
Page 67
Small lights Small lights High beam High beam Rotate the knob to to turn on small Rotate the knob to and push the light lights. (They include the daytime running handle of the combination switch from the lights, rear sidelights, rear license plate normal position forward (away from the lamp, dashboard background light, small steering wheel).
Page 68
Lighting delay Lighting delay • When the vehicle is powered on, tap → Vehicle settings → Light @ ambient → Headlight after exit to set the delay time. Auto light off Auto light off • Conditions for enabling the auto light off function: when the light button on the multifunctional switch is toggled to "...
Page 69
CAUTION environment. •When the vehicle collision or sensors REMINDER have been reinstalled, contact a BYD authorized dealer or service provider •When HMA is activated, the high to calibrate the sensors, so as to avoid beam assist indicator light on the affecting system performance.
Recommended Vehicle Loading Headlight Height Conditions Adjustment Level One person in the driver seat The driver, plus one passenger in the front seat All the seats occupied • Push up or pull down the stick to select All the seats occupied, a mode.
Page 71
• When the knob is rotated to the " " position and released, the wiper operates once or twice further after the spray has stopped. Rear Windshield Wiper and Washer • Rotate the wiper knob to the Link between rear wiper and trunk Link between rear wiper and trunk position to start the rear windshield wiper.
Front Door Switches Smart window control function* Smart window control function* • Smart Key: this function can be enabled Electric Windows in the infotainment system (for details, see the infotainment settings). When the remote control key unlock button • When ignition status is on OK, the is pressed and held, the windows will window control switch can be used to roll down automatically.
Page 73
•The anti-pinch function may fail right before the window is fully close. •When the auto raise and anti-pinch functions do not work, contact a BYD authorized dealer or service provider. Window Lock Button* • All doors are automatically unlocked •...
Trunk Switch • Pull this switch to open or close the trunk from inside the vehicle. (2) BSD Switch* This switch enables the BSD function. (For details, see "Blind Spot Detection System Setup*".) (3) AVH switch* Odometer Toggle Switch This switch enables the AVH function. (For details, see "AVH switch".)...
Emergency Warning Light Button When the Emergency Warning Light Button is pressed, all turning lights and turn signals on the instrument panel start flashing. They all stop flashing when the button is pressed again. • The vehicle will be exclusively on snow mode when this button is pressed.
• When the switch is OFF, the CAUTION passenger airbag is de-activated. The PAD status bar will •In soft snow conditions, if motor display . In the event of performance is worsened due to moderate to severe impact, and the the dynamic stability control being triggering conditions being met, the activated, turning off the ESC system...
Sunroof Switch Open/Close Sunshade Opening the sunshade Opening the sunshade Panoramic Sunroof • Press and hold the sunshade open button (1) to open the sunshade. The The sunroof can only be operated under OK sunshade stops if the button is released. ignition status or when the power-off delay has not expired.
Interior Light Switches Sunroof Anti-Pinch Function If the sunroof closing process is obstructed Front Interior Lights by anything, it will stop and slightly retract. Left interior light button WARNING Right interior light button • Keep clear of the sunroof when it is opening or closing.
Page 79
Ambient Lights When the door is opened, the intelligent interior ambient lights go on automatically to create a pleasant environment in the cabin. • Tap on → Vehicle settings → Light & ambient to set the following ambient light parameters: •...
USING AND DRIVING Charging/Discharging......80 Batteries..........91 Usage.Essentials........95 Starting.and.Driving......101 Driving.Assistance.Functions....108 Instructions.for.Other.Main.. Functions..........131...
In addition, keep charging, stop immediately and contact minors away from the vehicle when a BYD authorized dealer or service charging. provider. • Charging may affect medical or • Always observe the following implanted electronic devices.
Page 82
• The signs refer to standardized charging • Pull the connector with one hand. systems in accordance with DIN EN • Do not forcibly pull out the charging 62196. connector when the port is locked. • The vehicle can be powered on to use Charging Precautions the A/C while charging, however, this is not recommended.
Page 83
• During DC charging, low temperatures • During charging, the estimated and high SOC will reduce the charging remaining time to full charge is current due to the battery's low displayed on the instrument cluster or temperature characteristics. Therefore, infotainment system. Depending on to improve charging speed, charging the temperature, SOC, and charging with a low SOC is recommended.
Page 84
Check for power system fault/failure warning Vehicle or AC charging light or message on the instrument cluster. connector failure If found, stop charging and contact a BYD authorized dealer or service provider. Power battery temperature above or Warm up or cool down the power battery.
When using it, avoid it getting rolled CAUTION over by the vehicle, dropped, or trampled on. •Contact a BYD authorized dealer or service provider, or a BYD authorized • Never drop the device. Never move technician, to select the appropriate it by pulling it directly by its cable.
Page 86
• Open the hatch and remove the WARNING port cover. Make sure the port in not obstructed in any way. • Do not modify, disassemble, or repair the charging equipment and related ports. • It is not recommended to use any additional wire or adapter/ connector.
Page 87
2. Stopping charging 2. Stopping charging • Charging stops when the battery is fully charged. • To stop earlier, first disconnect the charging port by pressing the door handle microswitch while carrying the smart key and pulling out the charging coupler.
Page 88
• Single-phase AC charging pile • Close the AC charge port cover (see the portable AC charging process). • Use AC charging piles in public places to charge the vehicle. • Store the equipment properly. • Charging time: refer to the message on •...
Smart Charging Function 3. Stopping charging 3. Stopping charging • Stopping charging: • When the manager detects that the low voltage battery capacity is low, it can be • When early stop is set or charging has been completed, the charger will charged by the power battery, so it is automatically stop.
Page 90
CAUTION WARNING • Never use the equipment when the •For precautions on the use of discharge connection devices, refer discharging connector or power to article 3 of charging precautions, supply strip is disconnected, broken, charging precautions for charging or there is any sign of surface damage. equipment.
• After the connection is made, CAUTION discharge begins and respective information is displayed on the •After unlocking the charging connector, instrument cluster. it can be pulled out within 30 seconds. Stopping discharging Stopping discharging After 30 seconds, it will lock again. •...
• The set driving range display mode will • The corresponding settings can be be memorized by the system. made in "Multimedia → New Energy → Energy Management → Energy • When the vehicle is powered off and Regeneration Mode". then on, the display mode set last time will be maintained.
Page 93
Battery Properties • Driving habit: e.g. frequent acceleration/deceleration instead of uniform speed, or the range is shorter • It is normal that vehicle performance when driving at high speeds than is affected by battery electrochemical when at low speeds. properties and self-protection. Performance varies in the following •...
Page 94
If it comes into contact with How to scrap an NEV: skin or eyes, rinse immediately with plenty of water, and seek immediate 1. Take the vehicle to the BYD recycling medical attention. service provider that will assess the •...
Lead-acid batteries contain a not be able to power on the vehicle. In corrosive solution. To prevent this case, contact the BYD authorized damage to the battery or injury, do dealer or service provider. not disassemble or repair the battery •...
Keep children away from lead-acid • Driving safety and comfort totally storage batteries. depend on equipment usage and good driving habits. • BYD doesn't provide free warranty for the Usage Essentials damage or faults resulted from towing for commercial purposes. Break-In Period Driving Safety Precautions •...
Page 97
• When the vehicle is traveling, if the fault light is on, go to a BYD authorized dealer Suggestions for Vehicle Use or service provider for troubleshooting; • When the battery temperature is very Battery service life is extended when the high, vehicle performance will decline.
Page 98
How to Save Energy and 3. Reduce load: 3. Reduce load: Prolong Vehicle Service • Consumption is higher when air Life conditioning is used. When outside temperatures are moderate, the use of air circulation instead of air conditioning • Saving energy is simple and easy, and it reduces consumption.
Page 99
• • For trunk strapping or fastening supplies, Do not carry highly magnetic items, contact a BYD authorized dealer or for those might interfere in the the service provider. vehicle's operating functions. Flood Precautions Carrying Luggage in the Passenger Area •...
Page 100
Such damage is not covered by the • Go to a BYD authorized dealer or service vehicle's warranty either. provider for regular vehicle checks. • Vehicle wiring, connections, harnesses...
Page 101
• When the vehicle is being repaired or maintained, make sure the cathode end of the low voltage battery is disconnected. • In case of fire, keep calm and take the necessary steps to put it out. • Pay attention to early signs of fire, like unusual smell or noises.
Page 102
Starting and CAUTION Driving •Do not touch the power button while driving. Starting the Vehicle Remote Start Function In normal cases, start the vehicle as below: • Engage the parking brake firmly. Before starting the vehicle: • Switch the gearshift lever to P or N. 1.
Page 103
Carry out a safety check before driving long headrest height, and the steering wheel distances. The vehicle can also be taken to angle and height. a BYD authorized dealer or service provider • Adjust rear view mirror and side mirrors. for inspection. • Close all doors.
Page 104
• Before shifting into "D", ensure that the power switch is on "OK". • Press the pedal or the unlock button when shifting to P or D gear. For details, see the prompt message on the dashboard. • The lever returns to it middle position after it is released.
Page 105
EPB Automatic Release Upon CAUTION Vehicle Start •If the EPB switch is pressed and shutdown, EPB will not be pop up • When the vehicle is powered on, the automatically. This operation can be brake pedal is pressed and held, and used for towing or pushing the vehicle the gear is shifted into "D"...
Page 106
If it cannot be released, contact unusual noises are heard, contact a BYD a BYD authorized dealer or service authorized dealer or service provider provider immediately.
Page 107
AVH Running Conditions (all must be met) • The AVH function is ready. • In travel gear, the brake pedal is pressed to stop the vehicle. • The AVH function is enabled, brake lights go on, and the AVH indicator goes green.
Page 108
Quick 4. Use anti-freeze washer fluid. acceleration or sudden braking will cause skidding. • These can be found in the BYD authorized dealer or service provider and the auto parts stores. • The water and anti-freeze ratio must...
Page 109
Status description CAUTION • ACC off: ACC function disabled. •Do not use anti-freeze or other substitutes as washing solution, as • ACC stand-by: the system is in stand-by this may damage vehicle paint. by default when the vehicle is started, and can be manually activated.
Page 110
• There is no vehicle network • When the ACC function is active, vehicle communication failure prompt on the speed can be set within a 30~150 km/h dashboard. (20~95 mph) range, by toggling lever (2). By toggling lever (2) up/down, tarhet •...
Page 111
• When ACC is active and the break pedal • ACC can only respond to stationary or is pressed, ACC will go on stand-by slow-moving objects, such as vehicles, automatically. After the brake is released, the end of traffic, toll booths, bicycles or ACC needs to be reactivated.
Page 112
ACC will not be able to target it, so (covered in ice/snow or flooded). the driver must keep vehicle control. • In the following cases, go to a BYD • When the vehicle stops as it follows authorized dealer or service provider...
Page 113
Predictive Emergency Braking System • If the driver fails to respond to the emergency warning and the risk level increases, the system will enable the The predictive emergency braking AEB function. The system will engage system has two features: Predictive braking force as much as possible to Collision Warning (PCW) and Autonomous avoid collision or reduce crash impact.
Page 114
• Pedestrian detection fails due to • The system will not trigger AEB when the special clothing or other objects. driver is aware of an emergency warning, but turns the steering wheel, accelerates • Bends with small turning radius. or brakes. •...
Page 115
• Small spare tire or tire repair kit is target adaptive cruise speed within the used. speed limit in a certain period of time. • In the following cases, go to a BYD • Tap on → Dipilot → Driving Assist authorized dealer or service provider...
Page 116
• In case there is a collision, or the camera sensor is reassembled, go to a BYD authorized dealer or service provider for sensor calibration to prevent the system...
Page 117
The function returns once • Poor visibility in snowy, rainy and conditions return to normal. If it doesn't, foggy days. contact a BYD authorized dealer or service provider for processing. • Dirty or fogged windshield, or blocked multi-functional video controller.
Page 118
• When the function is enabled, the driver 2. If the vehicle enters a road segment must always hold the steering wheel and where lines become unclear or absent, control the vehicle when necessary. regardless of whether there is a target vehicle ahead, the ICC function will be •...
Page 119
Blind Spot Detection Side assist Side assist System* When speed is above 30 km/h and the sensor detects a vehicle approaching quickly on the adjacent lane, the side The blind spot detection (BSD) system mirror indicator lights up. If the turning light includes the following functions: blind spot for the same side is used at this moment, detection, lane assist, rear cross traffic alert,...
Page 120
Rear collision warning Rear collision warning CAUTION If vehicle speed is above 5 km/h and the •Detection may be affected or delayed sensor detects a risk of collision from a in some environments, and when vehicle approaching too quickly from the the radar cross-sectional area of rear, the side mirror light indicator will flash the target vehicle is too small (it...
Page 121
• If tire pressure is low when the vehicle degrade the system's performance. is powered off, a low pressure alarm In this case, contact a BYD authorized will prompt the driver to inflate when dealer or service provider. the vehicle is powered back on.
Page 122
• The running time of tire pressure system. This should be done by the monitoring module is related to the daily professional technicians from a BYD travel distance. authorized dealer or service provider; otherwise, system failure may occur.
Page 123
• Landscape mode: WARNING • Tap on the icons for front, rear, right • If tire pressure is abnormal, the system and left views at the left bottom of the does not prevent the vehicle from Infotainment screen, and single views driving.
Page 124
• After the vehicle starts, the image WARNING before last power-off is displayed on the invisible panoramic screen. • The cameras are mounted on the Foreign bodies in the underbody front bumper, on the lower sides of and surrounding blind areas may be the left and right side mirrors and inconsistent with the actual ones.
Page 125
• When the vehicle goes into reverse, • When the ignition status is on OK, EPB the system automatically enables the is released and Parking Assist is enabled Reversing View. automatically. • Never use other buttons under the Reversing View screen, except for volume and telephone related buttons.
Page 126
Working Sensors and Their (3) Rear right sensor* Detection Range (4) (5) Rear right sensor* (6) Rear left sensor* All sensors are activated upon reversing. The figure shows the sensors' detection Distance Display and Speaker range. Sensors have a range limitation, so drivers must check the surroundings before slowly reversing the vehicle.
Page 127
If such issue persists, go • The vehicle is moving on particularly to a BYD authorized dealer or service bumpy roads, slopes, gravel or grass. provider for inspection. • The sensor has been repainted.
Page 128
Vehicle Dynamic Control (VDC) Vehicle Dynamic Control (VDC) Controller Deceleration Parking (CDP)* Controller Deceleration Parking (CDP)* If the vehicle swerves from the driver's When the EPB switch is pulled, the CDP normal lane, the VDC will correct the function starts working and the vehicle situation by engaging brakes to the brakes at a constant deceleration (0.4 g corresponding wheels to help control...
Page 129
• HDC speed control: • To enable or disable this function, tap on Infotainment → Vehicle Settings • HDC works in speeds between 11 and → Drive Comfort Adjust, and go to 38 km/h, within which the speed can "Comfort Parking" settings. be adjusted by pressing/releasing the accelerator or brake pedal, whichever •...
Page 130
• For details on tire or wheel • When the ABS is working, the brake replacement, contact a BYD authorized pedal will vibrate, which may produce dealer or service provider. noise. This is because the ABS is in pulsating prompt brake, which is normal.
Page 131
•If the ABS warning light is still on while the brake system warning light turns on stop the vehicle in a safe place immediately and contact a BYD authorized dealer or service provider. •ABS cannot prevent skidding caused by sudden changes of direction, such as turning a corner or changing lanes suddenly.
Page 132
If it is confirmed that there is no sound, • Do not use this function before contact a BYD authorized dealer or becoming fully familiar with the service provider to deal with it. vehicle, so as to avoid accidents.
Page 133
Electronic Side Mirrors WARNING • Side Mirror Adjustment Buttons Do not hang heavy objects from the rear view mirror, or forcefully shake or drag it. Manually folding side mirrors Manually folding side mirrors • When manually adjusting the rear Push the outer edge of the side mirror to view mirror, do not adjust forcibly if it rotate the mirror body around the folding gets stuck.
Page 134
• The right side mirror can be selected Replacing Front Wipers Replacing Front Wipers by pressing the corresponding auto 1. Pull the wiper arm at the driver side, and regulation switch then pull the other at the passenger side; 2. Press the Wiper Lock button (1); •...
Page 135
• The lower layer of the auxiliary console CAUTION is equipped with a special SD card slot for DVR. •Do not open the hood when the wiper arms are pulled up. •Lower the wipers slowly, avoiding direct impact onto the windshield. •Do not bend the wiper blade, and do not obstruct the wiper blade when the wiper is in operation.
Page 136
• Tap on this button again to disable. • View the recorded video in the Playback list. REMINDER •If the car is not equipped with an SD card, consult the local BYD authorized dealer or service provider, then purchase the appropriate type and install it. Taking pictures •...
Air Conditioning System A/C Panel View Front A/C buttons: Front A/C buttons: ① Auto button ② A/C ON/OFF button ③ Defrost button for front windshield A/C Operation Interface • Tap on → Vehicle settings → A/C to enter the A/C settings interface. Fan speed reduction during calls Remote A/C schedule mode Auto air recirculation when parking...
Page 140
Setting fan speed reduction during calls Setting fan speed reduction during calls • Tap on this button to enable this setting. • Tap on this button again to disable it. Setting auto air recirculation when parking Setting auto air recirculation when parking •...
Page 141
Front Row A/C Operation Interface A/C Settings button Defrost button for front windshield Air Purification System* Defrost button for rear windshield & side mirrors* Seat Heating button* Internal/external circulation button A/C Operations button Ventilation button A/C ON/OFF button Front passenger A/C temperature regulation button AUTO Mode button Blowing Mode button...
Page 142
Function Definitions REMINDER AUTO Mode button AUTO Mode button •When the parking automatic internal circulation is enabled, to ensure air • After tapping on this button, its indicator quality in the vehicle and prevent lights up on the front A/C panel, and the vehicle exhaust from entering compressor status, air amount and the vehicle, the circulation mode...
Page 143
• Tap on this button again to disable the function. • This function is not to be used to dry raindrops or melt snow. REMINDER •Using the side mirror electric heating defrosting function for a long time may cause the mirror to wear out Usage Essentials faster.
Page 144
» Keep the cabin clean. •If the unpleasant smell persists, contact a BYD authorized dealer or service provider for repair. •It is normal that the A/C blower keeps running after the vehicle is locked. That is because the condensed water...
Page 145
Air Purification System* When A/C is enabled, the air purification system thoroughly removes PM2.5 particles from the air blown into the cabin. Air Purification Operation Interface Tap on the "Air purification" button on the Infotainment operation interface to enter. Air Purification Button Quick Purification Button Outside PM2.5 Value and Level Display In-vehicle PM2.5 Value and Level...
Page 146
• A/C ON: tap on the "A/C ON" button on the daily or real-time PM2.5 value of the the BYD APP control interface, and tap air published by the state and relevant on the "Set temperature", "Duration" and government authorities.
Storage Center Console Cubby Door Bins • Located between the front seats, open the cover to use. • There is a door bin on each door for storage of beverage bottles or small items. File Pockets • There are file pockets on the front seat Glove Box backrests.
Cup Holder • The front seat cup holder is located inside the center console cubby. (2) Vanity mirror (2) Vanity mirror • There is a vanity mirror on the inner side of the sun visor. Slide the cover for use. REMINDER CAUTION! •Correct use of the sun visor improves...
Page 149
USB Ports 12 V Auxiliary Power Outlet There are two ports installed in the lower layer of the auxiliary console. • It can be used for accessories with 12 V DC working voltage and no more than ① Type-A port for data transfer. 10 A working current.
Page 150
• To disable wireless charger, pull CAUTION! down the PAD quick menu to find the deactivation setting. The indicator will •BYD will not assume any responsibility go off. for any problems caused by improper use. If the product is disassembled or modified, the free warranty will be terminated.
Page 151
If charging is still unavailable, contact a BYD authorized dealer or service provider. WARNING! •After powering off, if the phone is still •When installing the luggage...
Infotainment WARNING! System •Do not use a high-power inverter in the vehicle, as this may cause the Infotainment Control infotainment system to malfunction. Panel PAD •Do not format or root the device without authorization, or it will cause the infotainment system or the When the vehicle is powered on, the initial vehicle to malfunction.
Page 153
Widgets Language Setting • When the Infotainment is ON, the widget • When the vehicle is powered on, tap on screen is automatically displayed, → Dilink → More → Language on which contains the following modules: the center console touch screen and set top status bar, Vehicle settings, A/C, the language as Simplified Chinese or Navigation bar, and widget window:...
Page 155
• It is recommended that the maintenance be performed in accordance with the standards and specifications of BYD Auto Co., Ltd., and by a local BYD authorized dealer or service provider.
Page 156
Maintenance Schedule The vehicle maintenance is performed based on the mileage or months, whichever comes first. Maintenance items Maintenance interval The initial inspection should be performed at 3 months or Chassis fastening anchor 5,000 km, the second inspection at 12 months or 20,000 km, and screws checkup subsequent inspections every 12 months or 20,000 km, where damaged parts should be replaced in time.
Page 157
The initial inspection should be performed at 3 months or 5,000 km, the second inspection at 24 months or 40,000 km, and subsequent inspections every 24 months or 40,000 km; Ball pin and boot checkup where under harsh conditions, the initial inspection should be performed at 3 months or 5,000 km, the second inspection at 12 months or 20,000 km, and subsequent inspections every 12 months or 20,000 km.
Page 158
Drive motor anti-freeze Replace the long acting organic acid refrigerant once every replacement 4 years or 100,000 km, whichever comes first. The initial inspection should be performed at 3 months or 5,000 km, the second inspection at 12 months or 20,000 km, and Brake fluid checkup subsequent inspections every 12 months or 20,000 km, where damaged parts should be replaced in time.
Page 159
The initial inspection should be performed at 3 months or 5,000 km, the second inspection at 12 months or 20,000 km, and Checking of the activated subsequent inspections every 1 year or 20,000 km, whichever carbon HEPA filter* comes first. Where under harsh condition, check every 6 months and replace when necessary.
Page 160
BYD Auto • Use as taxi. Co., Ltd., and by a local BYD authorized dealer or service provider. • Driving in congested urban areas at temperatures above 32°C for more than •...
Page 161
If fragments or provider. cracks peel off from the metal surface, please go to a BYD authorized dealer • Do not touch the paint with a greasy or service provider for repair. cloth. Do not place greasy tools or rub with organic solvents on the vehicle body so as to avoid chemical reactions.
Page 162
Manual Car Washing • The vehicle should be taken for a paint check regularly (once a month or whenever any problem is found), and Before washing the vehicle, park it in the waxed once every three months. shade, and wait for the vehicle to cool down sufficiently.
Page 163
Carpet Cleaning REMINDER • Clean carpets with a good foam •Do not scrape or use gasoline to detergent. remove dirt. The plastic wheel trims are easily damaged by organic matter. • Use a vacuum cleaner to remove as If any organic matter is splashed on much dust as possible.
Page 164
• For any questions about vehicle CAUTION cleaning, please consult a local BYD authorized dealer or service provider. •When cleaning the inside of the rear window, be careful not to scratch CAUTION or damage the heating wire and the connector.
Page 165
Tire Checks • Note that improper and incomplete maintenance will affect the good use of the vehicle. The following items should be checked according to usage or specified mileage: • This section only lists instructions on simple maintenance items that can •...
Page 166
• For each new vehicle, front combination •If there is a noticeable amount of lights are already calibrated in the water inside the lights, drive to a BYD factory. If the vehicle often carries heavy authorized dealer or service provider loads, the front combination lights may for maintenance.
Page 167
5. When washing the vehicle, do not aim 5. The sunroof freezes easily in winter, jets directly at the sealing strips with a the sealing strips or other parts may water cannon, to prevent damage to the be damaged if the sunroof is forcibly strips and water from leaking into the opened.
Page 168
• If possible, start the vehicle regularly (preferably monthly). If the vehicle has REMINDER been parked for a year or more, go to a BYD authorized dealer or service provider •Confirm that the hood is closed and for comprehensive maintenance. locked securely. Otherwise, while...
Page 169
• High quality windshield washer fluid •It is recommended to go to a BYD should be added to improve stain authorized dealer or service provider removal and prevent freezing in cold to add refrigerant that is compatible weather.
Page 170
Maintenance Rules • If A/C efficiency decreases, go to a BYD authorized dealer or service provider for • Clean windscreen and blade regularly maintenance. (preferably once a week or once every two weeks).
Page 171
• When there are marks on the windshield • Over-inflated tires wear unevenly, reduce caused by gravel, maintenance should comfort, and are prone to damage from be carried out timely (it is recommended uneven roads. If seriously over inflated, that windshield repair resin products there is a risk of bursting, seriously should be used and the windshield threatening safety.
Page 172
• In addition to proper inflation, proper wheel alignment also helps reduce tread wear. • If uneven tire wear is found, go to a BYD authorized dealer or service provider and check the wheel alignment. • The vehicle has been balanced in the factory, but tires need to be re-balanced after driving for a period of time.
Page 173
• Go to a BYD authorized dealer or service •Do not mix radial tires, bias belted provider for replacement of original tires. tires or diagonal ply tires.
Page 174
•Do not use a fuse with a higher rated ampere value, or any other solution to replace the fuse, as this may cause serious damage or even a fire. •If a fuse blows, go to a BYD authorized dealer or service provider for inspection or replacement.
Page 175
Under Hood PDB Nameplate Number Ampere (A) Protected Component or Circuit PTC3 High-voltage all-in-one...
Page 176
Electric compressor Brake light switch PTC2 PTC1 Rear windshield defroster Front wipers Auxiliary power outlet Auxiliary power outlet High-voltage all-in-one Rear body controller ADAS...
Page 177
Blower Rear wiper Batteries C-EPS Electric fan...
Page 178
Dashboard Panel PDB Nameplate Number Ampere (A) Protected Component or Circuit Rear body controller Thermal management integrated module Diagnostic port Instrument cluster High-frequency receiving module...
Page 179
Shift panel Infotainment system External power amplifier ADAS Combination switch On-board charger Rear body controller Rear body controller Front left Front right...
Page 180
REMINDER •Different vehicle configurations have some different fuse amperages (such as multimedia). Maintenance and replacement should be based on the actual object.
Page 182
WHEN FAULTS OCCUR When.Faults.Occur......182...
Page 183
If the smart key indicator does not flash and the vehicle can't be started using the start function, the smart key battery may be exhausted. In this case, contact a BYD authorized dealer or service provider as soon as possible to change the battery.
Page 184
Vehicle Fire Rescue 2. Call a BYD authorized dealer or service provider and the fire brigade, informing them that the vehicle is equipped with a In case of fire, continue to operate the high-voltage battery pack, and wait for vehicle as follows according to the actual rescue.
Page 185
The orange cables are part of the high voltage harness. Users must not repair the high voltage system by themselves. If any repair is required, go to a BYD authorized dealer or service provider for repair. Towing Hook •...
Page 186
In-Vehicle Tools REMINDER The in-vehicle tools are stored in the toolkit • Towing the vehicle with the towing under the trunk cover. hook is not recommended. In-vehicle tools include: Warning triangle, • Only the vehicle's original towing reflective vest, wheel nut cover removal hook is to be used.
Page 187
If the tire sealant comes into contact •After using the tire sealant, buy a new with the skin or gets into the eyes, one at a BYD authorized dealer or thoroughly rinse the affected body service provider. part immediately with plenty of clean water.
Page 188
When the Battery Runs When the vehicle cannot start due to low battery level, try to start it in the following steps: 1. Open the hood. (Please refer to "Maintenance - Self-Maintenance – Hood".) 2. Connect one end of the red positive (+) 5.
Page 189
• If the vehicle being rescued cannot be •Do not place the lifting boom or the started after several attempts, contact jack on the power battery. a BYD authorized dealer or service •Ensure firmness when lifting or provider. jacking up the vehicle.
Page 191
Data Information Vehicle Parameters Dimensions: Dimensions: Length (mm) 4455 Width (excluding side mirrors) 1875 Height (mm) 1615 Wheelbase (mm) 2720 Front track (mm) 1575 Rear track (mm) 1580 Front overhang (mm) Rear overhang (mm) Approach angle (°) Departure angle (°) Vehicle mass parameters: Vehicle mass parameters: Curb weight (kg)
Page 192
Power performance parameters: Power performance parameters: Max. design speed (km/h) Max. gradeability (%) Vehicle economic parameters: Vehicle economic parameters: Power consumption per 100 km under comprehensive working conditions ≤14.9 ≤14.8 (kWh/100 km) Driving range under comprehensive working conditions (km) CAUTION! •Actual power consumption depends on factors such as vehicle conditions, road conditions and driving habits.
Page 193
Braking system technical parameters: Braking system technical parameters: Free stroke of brake pedal (mm) ≤5 Reasonable thickness range of front brake disc (mm) 24~26 Reasonable thickness range of rear brake disc (mm) 10~12 Reasonable thickness range of front brake lining (mm) Reasonable thickness range of rear brake lining (mm) 2~6.5 Power battery parameters:...
Page 194
Vehicle Identification Vehicle Identification Number (VIN) Attached to the VIN slot on the upper Attached to the sheet metal clad of the cover of the right front windshield right rear wheel; cross sill; Attached to the gearbox body; Attached to the sheet metal surface inside the right rear door sill;...
Page 195
Drive Motor Model and Number VIN is engraved on the lower beam of the front right seat. (1) The model and number of the drive motor are located near the lock ring right under the hood. Note: The vehicle identification number (VIN) can be read in the upper right corner after selecting the model by connecting the VDS.
Page 196
Side airbag warning labels are attached The child protection lock logo is engraved below the left and right B-pillar lock rings. on the metal sheet surface on the left/right rear door. Airbag warning labels are printed on the front and back of the left sun visor. The usage tip sticker of the charging connector is attached to the inner surface of the charge port cover.
Page 197
Transponder Mounting Position The transponder mounting position is located in the upper left of the front windshield. CAUTION! •While affixing the electronic labels, do not overlap them with any glass frame or other object.
Page 198
Numbers Charging Port Electric Lock Control Function ����������90 0-100 km/h: Full Throttle Child Protection Lock ������������58 Experience ���������������������������131 Child Restraint System 12 V Auxiliary Power (CRS) ��������������������������������������25 Outlet �����������������������������������148 Cooling System �������������������167 Cup Holder ��������������������������147 A/C Operation Interface ������138 A/C Panel View ���������������������138 Data Collection and ACC System* ������������������������108 Processing �����������������������������32...
Page 199
Instrument Cluster View �������36 Intelligent Cruise Control File Pockets �������������������������146 System* ��������������������������������116 Fire Prevention ����������������������99 Interior Cleaning �����������������162 Flood Precautions �����������������98 Interior Light Switches ����������77 Folding in Rear Seats ������������61 Introduction to Airbags ���������19 Front Door Switches �������������71 Introduction to Keys �������������48 Front Seat Adjustment ����������60 Introduction to Seat Belts �����16 Front Seat Side Airbags ���������20...
Page 200
Parking Assistance Transponder Mounting System ���������������������������������123 Position ��������������������������������196 Power Battery ������������������������91 Predictive Emergency Braking System �������������������112 USB Ports �����������������������������148 Using Seat Belts ��������������������16 Rear View Mirror ������������������131 Regular Maintenance ����������159 Vehicle Cleaning ������������������161 Vehicle Corrosion Prevention ���������������������������160 Safety Handle ����������������������147 Vehicle Fire Rescue �������������183 Seat Information �������������������59 Vehicle Identification ����������193...
Page 201
Abbreviations List Abbreviations Abbreviations Abbreviations Full Name Full Name Anti-lock Braking Electronic Control Unit System Adaptive Cruise AUTO Automatic Control Universal Serial Bus Economic NORMAL Normal SPORT Sport Automatic Vehicle State of Charge Hold Predictive Collision Electric Parking Brake Warning Autonomous Blind Spot Detection Emergency Braking...
Need help?
Do you have a question about the ATTO 3 2022 and is the answer not in the manual?
Questions and answers
Front and back seats sizes required for make custom design seat covers