Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Haier HSU-088M06
Summary of Contents for Haier HSU-088M06
- Page 1 HSU-088M06 HSU-098M06 HSU-108M06 HSU-128M06 HSU-188M06...
- Page 2 5-13 14-15...
- Page 3 Cautions The machine is adaptive in following situation I. Applicable ambient temperature range: Indoor Cooling Outdoor Indoor Heating Outdoor 2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similar qualified person. The type of connecting wire is H05RN-F or H07RN-F 3.
-
Page 4: Parts And Functions
. ( D o n ' t a d j u s t i t m a n u a l l y . ) Outdoor Unit HSU-088M06 HSU-098M06 HSU-108M06... -
Page 5: Operation
Parts and Functions Operation ON/OFF TEMP MODE SWING SLEEP LOCK Clock set When unit is started for the first time and after replacing batteries in remote controller, clock should be adjusted as follows: Press CLOCK button, "AM" or "PM" flashes. Press to set correct time. - Page 6 Parts and Functions Operation like the following figure: ON/OFF MODE SWING SLEEP HEALTH LOCK BRIEF INTRODUCTION TO HEALTH OPERATION The anion generator in the air conditioner can generate a lot of anion to effectively balance the quantity of position and anion in the air and also to kill bacteria and speed up the dust sediment in the room and finally clean the air in the room.
- Page 7 Operation Remote controller's operation When in use, put the signal transmission head directly to the receiver hole on the indoor unit. The distance between the signal transmission head and the receiver hole should be within 7m without any obstacle as well. Don't throw the controller, prevent it from being damaged.
- Page 8 Operation Auto run, Fan operation (1) Unit start Press ON/OFF button, unit starts. Previous operation status appears on display. (Not Timer setting) Power indicator on indoor unit lights up. (2) Select operation mode Press MODE button. For each press, operation mode changes as follows: AUTO COOL...
- Page 9 Operation COOL,HEAT and DRY operation Recommendations: (1) Unit start Press ON/OFF button, unit starts. Previous operation status appears on display. (Not Timer setting) Power indicator on indoor unit lights up. (2) Select operation mode Press MODE button. For each press, operation mode changes as follows: AUTO COOL...
- Page 10 Operation (5) Air flow direction adjustment After operation mode is selected, vertical flap will open automatically according to the mode. Referring to the Fig. COOL About 10 Up and down (Use remote controller) Press SWING button, vertical flap will move within the range shown in the Fig.
-
Page 11: Timer Operation
Operation TIMER Operation Set Clock correctly before starting Timer operation You can let unit start or stop automatically at following times: Before you wake up in the morning, or get back from outside or after you fall asleep at night. TIMER ON/OFF (1)After unit start, select your desired operation mode. - Page 12 Operation TIMER ON-OFF (1)After unit start, select your desired operation mode Operation mode will be displayed on LCD. Power indicator on indoor unit lights up. (2) Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: TIMER ON TIMER OFF Select TIMER ON-OFF.
-
Page 13: Emergency Operation
Operation Emergency operation and test operation Emergency Operation: Carry out this operation only when the remote controller is defective or lost. When the emergency operation switch is pressed, a" Pi "sound starts once, which means the start of this operation. In this operation, it is not possible to change the settings of temperature and air flow speed, it is also impossible to do an operation by the timer. - Page 14 Operation Comfortable SLEEP Before going to bed at night, you can simply press the SLEEP button and unit will bring you a sound sleep in selected mode. In COOL mode One hour after SLEEP mode starts, temp. will become 1 C higher than temp.
- Page 15 Operation HEALTH operation ON/OFF TEMP MODE TIMER SWING CLOCK SLEEP HEALTH LOCK RESET 1.Unit start Press ON/OFF on the remote controller, unit starts. 2.Health anion function Press HEALTH button. For each press, Air conditioner starts health anion function operation. For twice press, disappears,the operation stops.
-
Page 16: Maintenance
Maintenance Different models have different appearance Cleaning of unit casing Cleaning of remote controller Cleaning of air filter 1.Open inlet grille by pulling it upward. 3.Clean the filter Use a vacuum cleaner to remove dust,or wash the filter with water. After washing, dry the filter completely in the shade. - Page 17 Maintenance Better use of air conditioner Proper room temperature. Closing of doors and windows during operation Never fail to observe the followings Do not sprinkle water over the unit. Do not pull power plug. Cleaning of the air filter. P r o p e r t e m p e r a t u r e Effective use of the timer.
-
Page 18: Troubleshooting
Trouble shooting Before asking for service, check the following first. Phenomenon The system does not restart immediately. Noise is heard Normal Performance inspection Smells are generated. Mist or steam are blown out. Does not work at all. Multiple check Poor cooling Application temp.