Armacost Lighting ProLine 714421 User Manual

ProLine Wi-Fi RGB+W Color LED Controller
With RF Remote Control
Model # 714421
Full Safety High Compact
Protection Power Size
Wide Voltage Wireless Wi-Fi
Range Remote Connection
Works with the Tuya Smart App,
available at the iOS and Google Play stores
Introduction
This LED controller is designed to drive constant voltage RGB+White
LED products such as LED tape light or LED fixtures in a voltage
range of 6–24 volts DC. The receiver works with the RF wireless
remote control, which allows the user to choose between multiple
colors, adjust the LED brightness, and select dynamic effects.
Receiver & wiring
87mm
72mm
1 3
1. Input – from power supply
The controller input and output voltage range is 6–24 volts DC.
Make sure the LED lighting voltage is within this range and
below the rated wattage of the power supply. Connect input
wires from the power supply to the controller as indicated by
the polarity markings on the controller (+ to + and – to –).
2. Output – to LED lighting
Observe polarity indicated on the controller when connecting to
LED lighting (+ to +, G to G, R to R, B to B, and W to W).
Make sure the voltage of the LED lighting is the same as the power
supply and the maximum load doesn't exceed that of the controller.
CAUTION: Shorting of output cables could cause permanent damage
to controller. Make sure cables are well insulated from each other.
3. Controller status indicator
This light shows the controller status as follows:
Steady yellow: Remote only mode, Wi-Fi disconnected
Steady green: Remote and Wi-Fi mode
Single green blink: Command received
Long single yellow blink: Brightness or speed limit reached
Red flash: Overload protection
Yellow flash: Overheat protection
Green flash 3 times: Setup command received
4. Wiring diagram
Connect the power supply to the controller input and the controller
output to the LED lighting. The output voltage of the power supply
must be the same as the voltage of the LED lighting. Make sure all
power cables are conected securely and insulated before powering on.
100/230V
AC Power
Remote Control
5. On / Off
Press the
controller or the
off. The controller will remember
the controller state when powered
off, and will return to that state
when powered back on.
6. Mode selection
Press this key to switch between
RGB, white, and RGB+white mode.
If the RGB mode is selected, the
white channel will be disabled, and if the white mode is selected, RGB
channel will be disabled. In RGB+White mode all channels are enabled.
7. Select static RGB color
Press the "COLOR+" and "COLOR–" keys to scroll through the preset
library of colors.
8. Shortcut color keys
24mm
Press to select preset colors.
9. White brightness control
2
Press to increase white LED brightness and press
10. RGB brightness control
Press to increase RGB LED brightness and press
11. Dynamic effect
Press "MODE+" and "MODE–" to select the dynamic effect mode
and "SPEED+" and "SPEED–" to adjust the effect speed.
12. Remote indicator
When pressing keys, the indicator blinks if the remote is working
properly. If the indicator flashes slowly when pressing keys, battery power
is low and it needs to be replaced. Replace with a CR2032 battery.
13. Setting up a Wi-Fi connection
Install the Tuya app to set up a Wi-Fi connection. Before setup,
make sure the controller is in factory default mode and not
connected to other wireless routers. The controller indicator
should glow yellow before it has been connected to Wi-Fi.
Remote control operation
14. Using the remote control
Pull out plastic battery insulation tab before use. The RF wireless remote
will work through walls and doors. Do not install in a metal enclosure.
6–24V DC
Output LED LED
Power Supply Controller Lighting
6–24V DC 6–24V DC
5
6
key to turn on
key to turn
8
EFFECT
to decrease it.
to decrease it.
15. Pairing with a new remote control
The remote control and receiver are already paired,
but up to five remotes can be paired to one receiver.
To pair a new remote:
1. Disconnect power to receiver and wait five seconds.
2. Reconnect power and wait ten seconds.
3. Press the and
seconds until the remote indicator flashes quickly.
16. De-pairing remotes
To de-pair a remote control, pair the remote you wish to continue using
with the controller and any other paired remotes will be de-paired.
17. Reset to factory default
12
To reset the Wi-Fi setting and remote control pairing:
9
1. Unplug the receiver. Plug in after five seconds.
10
2. Press the and
7 seconds, within ten seconds of the receiver being powered on.
The indicator will flash yellow three times to confirm.
EFFECT
11
Safety Protection
The controller has a function to prevent it from being damaged by
mis-wiring, output short circuit, overloading, or overheating. It will
automatically shut down under these extreme conditions until safe operating
conditions are restored. To avoid shutdowns, make sure the installed LED
lighting is compatible with constant voltage driving, is in the rated range
of the controller, and the cables are well connected and insulated. Also,
install the controller with proper ventilation and heat dissipation in mind.
Specifications
Output mode .... PWM constant voltage
Working voltage ..................6–24V DC
Rated output current .. 4x3A (12A max)
Static colors .................. 30 (remote) /
................................16 million (app)
Brightness levels ........... 10 (remote) /
.........................................100 (app)
Dynamic effect modes ...34 (remote only)
Dynamic speed levels ...10 (remote only)
Color preset keys (remote) ............... 7
Scene / Timing function.....................
......................User defined (app only)
Music sensing color ...... Yes (app only)
Customer support
Email: support@armacostlighting.com
Phone: 410-354-6000
Monday–Friday, 9 a.m.–5 p.m., ET
Warranty
1-year limited warranty. This product is for dry location use only.
Improper installation, improper powering, abuse, or failure to use this
device for its intended purpose will void warranty. Proof of purchase is
required for all returns. Questions? Email support@armacostlighting.com.
keys simultaneously for about three
keys simultaneously for about three
PWM physical grade ..........4000 steps
Overload/heat protection ............... Yes
Remote frequency ............433.92MHz
Remote control range ...... >49 ft./15m
.................................... in open areas
Wi-Fi standard ........ IEEE 802.11a/b/g
Controller dimensions .......................
....................3.43 X 0.95 X 0.59 in. /
.............................. 87 X 24 X 15mm
Remote dimensions ..........................
...................3.41 X 1.42 X 0.329 in./
........................... 86.5 X 36 X7.5mm
armacostlighting.com
© 2020 Armacost Lighting.
All rights reserved.
201001