Page 1
KD-LH70R 3 7 63 1515 0 SERVICE MANUAL CD RECEIVER 49803 2003 KD-LH70R SOUND SOURCE L 13942296513 Area Suffix E ---- Continental Europe EX -------- Central Europ TABLE OF CONTENTS Important Safety Precautions ............1-2 Disassembly method .
Page 2
KD-LH70R SECTION 1 3 7 63 1515 0 Important Safety Precautions 1.1 Safety Precautions Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system.
Page 3
KD-LH70R 1.2 Preventing static electricity 3 7 63 1515 0 Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.
Page 4
KD-LH70R SECTION 2 3 7 63 1515 0 Disassembly method 2.1 Main body 2.1.1 Removing the front panel assembly (See Fig.1) (1) Push the detach button in the lower left part of the front panel and remove the front panel assembly in the direction Front panel assembly of the arrow.
Page 5
KD-LH70R 2.1.3 Removing the heat sink 3 7 63 1515 0 (See Fig.5) (1) Remove the two screws C and two screws D on the left side of the main body. Heat sink Fig.5 2.1.4 Removing the bottom cover (See Figs.6 and 7)
Page 6
KD-LH70R 2.1.5 Removing the rear bracket 3 7 63 1515 0 (See Fig.8) • Prior to performing the following procedure, remove the front panel assembly, front chassis assembly, heat sink and bottom cover. Rear bracket (1) Remove the three screws E, two screws F and two screws G on the back side of the main body.
Page 7
KD-LH70R 2.1.8 Removing the CD mechanism assembly 3 7 63 1515 0 (See Fig. 11) • Prior to performing the following procedure, remove the front panel assembly, front chassis assembly, heat sink, bottom cover, rear bracket, main board and CD mecha board.
Page 8
KD-LH70R 2.2 CD mechanism section 3 7 63 1515 0 2.2.1 Removing the top cover (See Figs.1 and 2.) (1) Remove the four screws A on the both side of the body. (2) Lift the front side of the top cover and move the top cover Joints a backward to release the two joints a.
Page 9
KD-LH70R 2.2.3 Removing the DET switch 3 7 63 1515 0 (See Figs.6 and 7.) (1) Extend the two tabs c of the feed sw. holder and pull out the switch. Tab c DET switch (2) Unsolder the DET switch wire if necessary.
Page 10
KD-LH70R 2.2.5 Removing the clamper assembly 3 7 63 1515 0 (See Figs.10 and 11.) • Prior to performing the following procedure, remove the top cover. Clamper arm spring (1) Remove the clamper arm spring. (2) Move the clamper assembly in the direction of the arrow to release the two joints d.
Page 11
KD-LH70R 2.2.7 Removing the pickup unit 3 7 63 1515 0 (See Figs.14 to 18.) Pickup unit • Prior to performing the following procedure, remove the top cover, connector board and chassis unit. (1) Remove the screw D and pull out the pu. shaft holder from the pu.
Page 12
KD-LH70R 2.2.9 Removing the trigger arm (See Figs.19 and 20.) 3 7 63 1515 0 • Prior to performing the following procedure, remove the top cover, connector board and clamper unit. Joint k (1) Turn the trigger arm in the direction of the arrow to release the joint k and pull out upward.
Page 13
KD-LH70R 2.2.11 Removing the mode sw. / select lock arm 3 7 63 1515 0 (See Figs.22 and 23.) • Prior to performing the following procedure, remove the top plate assembly. Top plate Select lock arm (1) Bring up the mode sw. to release from the link plate (joint t) and turn in the direction of the arrow to release the joint u.
Page 14
KD-LH70R 2.2.13 Removing the select arm R / link plate 3 7 63 1515 0 (See Figs.27 and 28.) • Prior to performing the following procedure, remove the top plate assembly. Link plate Joint c' Joint r (1) Bring up the select arm R to release from the link plate...
Page 15
KD-LH70R 2.2.15 Removing the loading roller assembly 3 7 63 1515 0 (See Figs.31 to 33.) • Prior to performing the following procedure, remove the clamper assembly and top plate assembly. Loading roller assembly (1) Push inward the loading roller assembly on the gear side...
Page 16
KD-LH70R 2.2.16 Removing the loading gear 5, 6 and 7 3 7 63 1515 0 (See Figs.35 and 36.) • Prior to performing the following procedure, remove the top cover, chassis unit, pickup unit and top plate assembly. Loading gear bracket (1) Remove the screw K attaching the loading gear bracket.
Page 17
KD-LH70R 2.2.17 Removing the gears 3 7 63 1515 0 (See Figs.37 to 40.) • Prior to performing the following procedure, remove the top cover, chassis unit, top plate assembly and pickup unit. Joint n' Loading plate assembly Pull out the loading gear 3. (See Fig.35.) (1) Pull out the feed gear.
Page 18
KD-LH70R 2.2.18 Removing the turn table / spindle motor 3 7 63 1515 0 (See Figs.41 and 42.) • Prior to performing the following procedure, remove the top cover, connector board, chassis unit and clamper assembly. Turn table (1) Remove the two screws L attaching the spindle motor as- sembly through the slot of the turn table on top of the body.
Page 19
6. Digital tester AM (MW) 522kHz ~ 1620kHz 7. Tracking offset meter (LW) 144kHz ~ 279kHz 8. Test Disc JVC :CTS-1000 9. Extension cable for check Dummy load EXTSH002-22P 1 Exclusive dummy load should be used for AM,and FM. For FM dummy load,there is a loss of 6dB between SSG output and antenna input.The loss of 6dB need not be considered...
Page 20
KD-LH70R 3.2 Flow of functional operation unit TOC read 3 7 63 1515 0 Power ON When the laser diode correctly When the pickup correctly moves Set Function CD emits to the inner area of the disc Microprocessor $82 $81...
Page 21
KD-LH70R 3.3 Troubleshooting 3 7 63 1515 0 3.3.1 Feed section Is the voltage output at Is the wiring for IC621 Is 3.3V present at IC681 IC621 pin "40" 5V or 0V? pin "40"? pin "20"? Check CD 8V Check the vicinity of and 5V.
Page 22
KD-LH70R 3.4 Maintenance of laser pickup 3 7 63 1515 0 3.5 Replacement of laser pickup (1) Cleaning the pick up lens Before you replace the pickup, please try to clean the lens Turn of the power switch and, disconnect the with a alcohol soaked cotton swab.
Page 24
KD-LH70R 4.2 BR24C32F-X (IC771) : EEPROM 3 7 63 1515 0 • Pin layout • Pin function Symbol Function WPIN Power supply. A0,A1,A2 No use connect to GND. Serial clock input. I/O Serial data I/O of slave and word address.
Page 26
KD-LH70R 4.5 HD74HC126FP-X (IC801) : Buffer 3 7 63 1515 0 • Pin layout • Pin function Input Output Note: H:High level L:Low level X:Irrelevant Z:Off(High-impedance) State a 3-state input • Block diagram Output Input L 13942296513 Output Sample as Load Circuit 1...
Page 27
KD-LH70R 4.7 HD74HCT126T-X : (IC503) Buffer 3 7 63 1515 0 • Pin layout • Pin function Input Output H : High level L : Low level X : Irrelevant Z : Off (Hhigh-impedance)state of a 3-stage output • Block diagram...
Page 28
KD-LH70R 4.8 LA47505 (IC301) : Power amp. 3 7 63 1515 0 • Block diagram Protective circuit Stand by Switch L 13942296513 Ripple Mute Filter circuit protective circuit Muting & On Time Control Circuit u163 1-28 (No.49803) http://www.xiaoyu163.com...
Page 29
KD-LH70R • Pin layout 3 7 63 1515 0 • Pin function Pin No. Symbol Function AC CONT1 Header of IC GND1 Power GND OUTFR- Outpur(-) for front Rch STBY Stand by input OUTFR+ Output (+) for front Rch...
Page 43
KD-LH70R 3 7 63 1515 0 Pin No Symbol I/O Descroption TMAX O TMAX detection result output pin. TMAX Detection Result TMAX Output Longer than fixed period "PV " Within fixed period "HiZ" Shorter than fixed period "AV "...
Page 44
KD-LH70R 4.22 UPD784215AGC220 (IC701) : Main micon 3 7 63 1515 0 • Pin Layout 100 ~ 76 26 ~ 50 • Pin function Pin No. Symbol Function CD RESET Reset output for CD sub-micon CD MUTING Muting request of CD sub-micon...
Page 45
KD-LH70R 3 7 63 1515 0 Pin No. Symbol Function BUZZER Buzzer output EPROM-DI I2C data input EPROM-DO I2C data output EPROM-CLK I2C clock output OPEN Door open switch 49~52 No use SD/ST Station detector or stereo indicator input...
Page 46
LCD DA Data output for LCD driver LCD CK Clock output for LCD driver L 13942296513 BUS I/O JVC BUS input/output control terminal (negative) BUS I/O JVC BUS input/output control terminal BUS SI JVC BUS data input terminal BUS SO...
Page 47
CD mechanism SW1 input terminal B.DET Backup power supply detection input terminal (H:Stop mode) P.DET Main power off detection input terminal (H:HALT mode) BUS INT JVC BUS communication start interrupt input terminal L 13942296513 MP3 REQ CD MP3 request signal input terminal VSS0 VDD1 3.3V...
Page 48
KD-LH70R 3 7 63 1515 0 L 13942296513 u163 VICTOR COMPANY OF JAPAN, LIMITED AV & MULTIMEDIA COMPANY MOBILE ENTERTAINMENT CATEGORY 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan (No.49803) Printed in Japan 200304WPC http://www.xiaoyu163.com...
Page 49
KD-LH70R 3 7 63 1515 0 SCHEMATIC DIAGRAMS CD RECEIVER KD-LH70R CD-ROM No.SML200304 Area Suffix E -------- Continental Europe EX ------------ Central Europe SOUND L 13942296513 SOURCE Contents Block diagram Standard schematic diagrams Printed circuit boards 2-5,6 u163 No.49803SCH COPYRIGHT 2003 VICTOR COMPANY OF JAPAN, LTD.
Page 50
KD-LH70R 3 7 63 1515 0 Safety precaution Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check.
Page 57
KD-LH70R 3 7 63 1515 0 < M E M O > L 13942296513 u163 http://www.xiaoyu163.com...
Page 58
KD-LH70R 3 7 63 1515 0 L 13942296513 u163 V ICTOR COMPANY OF JAPAN, LIMITED AV & MULTIMEDIA COMPANY 10-1,1Chome,Ohwatari-machi,Maebashi-city,371-8543,Japan Printed in Japan (No.49803SCH) 2003/04 http://www.xiaoyu163.com...
Page 59
KD-LH70R 3 7 63 1515 0 PARTS LIST [ KD-LH70R ] * All printed circuit boards and its assemblies are not available as service parts. Area suffix E------------ Continental Europe EX --------------- Central Europe L 13942296513 - Contents - Exploded view of general assembly and parts list (Block No.M1)
Page 60
KD-LH70R 3 7 63 1515 0 Exploded view of general assembly and parts list Block No. L 13942296513 u163 http://www.xiaoyu163.com...
Page 61
KD-LH70R 3 7 63 1515 0 General assembly Block No. [M][1][M][M] Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local QYSDST2606Z SCREW 2.6mm x 6mm QYSDST2606Z SCREW 2.6mm x 6mm...
Page 62
KD-LH70R 3 7 63 1515 0 CD mechanism assembly and parts list Block No. Grease TN-2001-1013 TNG-87 GP-501MK CFD-005Z GP-501A L 13942296513 u163 http://www.xiaoyu163.com...
Page 63
KD-LH70R 3 7 63 1515 0 CD mechanism Block No. [M][B][M][M] Symbol No. Part No. Part Name Description Local 30320101T FRAME 30320102T TOP COVER 30320115T DANPER F (x2) 30320116T DANPER R 303205505T CHASSIS RIVET 303205503T CHANGE P. RVT A...
Page 64
KD-LH70R 3 7 63 1515 0 Electrical parts list Main board Block No. [0][1][0][0] Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local D714 SLR-56MC3F D721 UDZS11B-X Z DIODE IC31...
Page 65
KD-LH70R 3 7 63 1515 0 Symbol No. Symbol No. Part No. Part Name Description Local Part No. Part Name Description Local C242 QERF1CM-226Z E CAPACITOR 22uF 16V M C909 QERF1AM-227Z E CAPACITOR 220uF 10V M C243...
Page 66
KD-LH70R 3 7 63 1515 0 Symbol No. Symbol No. Part No. Part Name Description Local Part No. Part Name Description Local R251 NRSA63J-104X MG RESISTOR 100kΩ 1/16W J R767 NRSA63J-473X MG RESISTOR 47kΩ 1/16W J R252...
Page 67
KD-LH70R 3 7 63 1515 0 Symbol No. Symbol No. Part No. Part Name Description Local Part No. Part Name Description Local D608 SML-310VT/JK/-X R646 NRS181J-102X MG RESISTOR 1kΩ 1/8W J D609 SML-310VT/JK/-X R650 NRSA63J-101X MG RESISTOR 100Ω...
Page 68
KD-LH70R 3 7 63 1515 0 Symbol No. Symbol No. Part No. Part Name Description Local Part No. Part Name Description Local C505 NDC31HJ-270X C CAPACITOR 27pF 50V J C646 NCB31HK-103X C CAPACITOR 0.01uF 50V K C506...
Page 69
KD-LH70R 3 7 63 1515 0 Symbol No. Symbol No. Part No. Part Name Description Local Part No. Part Name Description Local R549 NRSA63J-472X MG RESISTOR 4.7kΩ 1/16W J R656 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W J R550...
Page 70
KD-LH70R 3 7 63 1515 0 Packing materials and accessories parts list Block No. Block No. L 13942296513 KIT: A11A12 u163 3-12 http://www.xiaoyu163.com...
Page 71
KD-LH70R 3 7 63 1515 0 Packing Accessories Block No. [M][3][M][M] Block No. [M][5][M][M] Symbol No. Symbol No. Part No. Part Name Description Local Part No. Part Name Description Local FSPG4002-001 POLY BAG (x2) GET0129-001A INST BOOK...