Page 1
Mocksville, N.C. 27028 Doosan purchased Bobcat Company from Ingersoll-Rand Company in 2007. Any reference to Ingersoll-Rand Company or use of trademarks, service marks, logos, or other proprietary identifying marks belonging to Ingersoll-Rand Company in this manual is historical or nominative...
Page 2
QUALITY POLICY We will supply products and services that consistently meet the requirements of our customers and each other. CALIFORNIA Proposition 65 Warning Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects, and other reproductive harm.
Page 3
Foreword Machine models represented in this manual may be used in various locations worldwide. Machines sold and shipped into European common market countries requires that the machine display the EC Mark and conform to various directives. In such cases, the design specification of this machine has been certified as complying with EC directives.
Page 4
Nothing contained in this document is intended to extend any promise, warranty or representation, expressed or implied, regarding the Ingersoll--Rand products described herein. Any such warranties or other terms and conditions of sale of products shall be in accordance with the standard terms and conditions of sale for such products, which are available upon request.
Page 6
SECTION 1- - SAFETY SAFETY PRECAUTIONS If more than one compressor is connected to one com- mon downstream plant, effective check valves and General Information isolation valves must be fitted and controlled by work Ensure that the operator reads and understands the procedures, so that one machine cannot accidentally decals and consults the manuals before maintenance be pressurized or over pressurized by another.
Page 7
Exercise extreme caution when using booster battery. to each hose at the source of supply or branch line in To jump battery, connect ends of one booster cable to accordance with OSHA Regulation 29CFR Section the positive (+) terminal of each battery. Connect one 1926.302(b).
Page 8
SAFETY LABELS Look for these signs on machines shipped to international markets outside North America, which point out potential hazards to the safety of you and others. Read and understand thoroughly. Heed warnings and follow instructions. If you do not understand, inform you supervisor. Hot Surface Corrosion risk Lifting point...
Page 9
Read the Operation and Maintenance manual before operation or maintenance of this machine is undertaken. WARNING - - Maintain correct tire pressure. (Refer to the GENERAL INFORMATION section of this manual). WARNING: Consult the operation and maintenance manual before performing any maintenance. Rough Service Designation Wet Location Operation Do not stack...
Page 10
Oil Drain km/h WARNING undertake Do not exceed the speed limit. maintenance on this machine until the electrical supply is disconnected and the air pressure is totally relieved. Read the Operation and Maintenance manual before operation or maintenance of this machine is undertaken remove Operating...
Page 11
Look for these signs on machines shipped to markets in North America, which point out potential hazards to the safety of you and others. Read and understand thoroughly. Heed warnings and follow instructions. If you do not understand, inform you supervisor. Indicates the presence of a hazard which WILL cause serious injury, death or property damage, if ignored.
Page 12
WARNING WARNING Improper operation of this equipment. Modification or alteration of this machine. CAN cause serious injury or death. CAN cause serious injury or death. Read Operator’s Manual supplied with this Do NOT alter or modify this machine without the machine before operation or servicing.
Page 13
WARNING WARNING Disconnected Air Hoses Whip. CAN cause serious injury or death. Combustible Gas. CAN cause serious burns, blindness or death. When using air tools attach safety device (OSHA Valve) at source of air supply for Keep sparks and open flames away each tool.
Page 14
SECTION 2 - - Warranty Ingersoll--Rand, through its distributor, warrants that each item of equipment manufactured by it and delivered hereunder to the initial user will be free of defects in material and workmanship for a period of three (3) months from initial operation or six (6) months from the date of shipment to the initial user, whichever occurs first.
Page 15
Ingersoll- -Rand Platinum Drive Train Warranty (Optional) – Platinum drive train pertains to the Ingersoll-- Rand Engine and Airend combination. The earlier of sixty (60) months from shipment to, or the accumulation of 10,000 hours of service. The starter, alternator, fuel injection system and all electrical components are excluded from the extended warranty.
Page 16
GENERAL WARRANTY INFORMATION GENERAL WARRANTY Extended Coverage Portable Compressor Package 1 year/2000 hours Airend 2 years/4000 hours 5 years/10,000 hours Limited warranty, major components (refer to operator’s manual). Portable Genset 8KW, 11KW, 20KVA Package 1 year/2000 hours None thru 575KVA Generator 2 years/4000 hours None...
Page 17
Extended Limited Airend Warranty Ingersoll--Rand Portable Compressor Division is pleased to announce the availability of extended limited airend warranty. Announcement of the extended warranty coincides with the introduction of PROSTECt Compressor Fluid. PROSTECt Compressor Fluid is an amber colored fluid specially formulated for Portable Compressors and is being provided as the factory filled fluid for all machines except ! XHP650/900/1070 models.
Page 18
WARRANTY REGISTRATION Complete Machine Registration Machines shipped to locations within the United States do not require a warranty registration unless the machine status changes (i.e. change of ownership). Machines shipped outside the United States require notification be made to initiate the machine warranty.
Page 19
WARRANTY REGISTRATION Selling Distributor Servicing Distributor Name Name Owner/User Name Address Address Address City City City County County County State State State Zip Code Zip Code Zip Code Telephone Telephone Telephone Complete the Applicable Blocks Owner/User Type of Business (check one only) Construction--Heavy Asphalt Contractor Other Mining...
Page 21
SECTION 3 - - NOISE EMISSION This section pertains only to machines distributed within the United States. WARNING TAMPERING WITH NOISE CONTROL SYSTEM PROHIBITED Federal law prohibits the following acts or the causing thereof: (1) The removal or rendering inoperative by any persons, other than for purposes of maintenance, repair, or re- placement, of any device or element of design incorporated into any new compressor for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use;...
Page 22
NOISE EMISSION CONTROL MAINTENANCE LOG COMPRESSOR MODEL SERIAL NO. USER UNIT NO. UNIT IDENTIFICATION DEALER OR DISTRIBUTOR FROM WHOM PURCHASED: Engine Make & Model: Serial No.: Purchaser or Owner: Address: Date Purchased: The Noise Control Act of 1972 (86 Stat. 1234) prohibits tampering with the noise control system of any compressor manufactured and sold under the above regulations, specifically the following acts or the causing thereof: (1) the removal or rendering inoperative by any persons, other than for purposes of maintenance, repair, or re- placement, of any device or element of design incorporated into new compressor for the purpose of noise control...
Page 23
MAINTENANCE SCHEDULE ITEM AREA PERIOD Compressed Air Leaks As Detected Safety and Control Systems As Detected Acoustic Materials Daily Fasteners 100 hours Enclosure Panels 100 hours Air Intake & Engine Exhaust 100 hours Cooling Systems 250 hours Isolation Mounts 250 hours Engine Operation See Operator’s Manual Fuels &...
Page 24
MAINTENANCE RECORD FOR NOISE EMISSION CONTROL AND EXTENDED WARRANTY ITEM NO. DESCRIPTION OF WORK HOURMETER MAINT/ LOCATION CITY/ WORK DONE BY READING STATE (NAME) INSPECT DATE Book 35393065 (7/02)
Page 26
SECTION 5 - - OPERATION CONTROL PANEL 10. Compressor Discharge Pressure Gauge - - Indicates pressure in receiver tank, psi (kPa). 11. Fuel Level Gauge - - Indicates amount of fuel in tank. CONTROLS (Standard) 12. Power Switch - - Flip “ON” to activate systems prior to Starting.
Page 27
UTILITY PACKAGE SET- -UP (no running gear) INSTALLATION The unit must be secured to a vehicle bed using mounting holes provided, to prevent unwanted motion of the unit while running or transporting. See Figure X for mounting holes provided in base. The air going into the inlet grilles must be relatively free of oil, dirt, soot and other debris.
Page 29
removing a pressure cap from a liquid cooling system for the engine. The sudden release of SETTING - - UP (ALL UNITS) pressure from a heated cooling system can result in a loss of coolant and possible severe personal • Position as level as possible. The design of these units permits a 15 degree sidewise limit on injury.
Page 30
If equipped with the optional cold starting aid The coolant must cover the tubes in the top tank (ETHER), operate the valve once or twice ONLY while (approximately 1 inch high on a clean measuring rod the engine is cranking. stuck down filler neck).
Page 31
compressed air is available at the service air valves in this mode. Hose Reel Operation To Unwind Hose 1. Disconnect end of hose from docking port at bottom right--hand corner of compressor. 2. Release reel lock pin on left--hand side of reel by S In “Gen/Air”...
Page 32
AUTOMATIC SHUTDOWN Units with Diagnostic Lamps: In a shutdown situation, the function of the panel This unit is protected with sensors (switches) for high lamps is to indicate what specific failure caused the discharge air temperature, high engine coolant unit to shut down.These lamps will remain illuminated temperature and low engine oil pressure.
Page 33
P130WJDU Speed and Pressure Regulator Adjusting Instructions Normally, speed and pressure regulation requires no adjusting, but if proper adjustment is lost, proceed as follows. Refer to the General Data table for proper engine speeds. Before Starting Remove regulator valve cover (A), (if equipped) on valve (B) to expose adjusting screw (C).
Page 34
P175 - - 185 Speed and Pressure Regulator Adjusting Instructions If equipped, place the Start--Run Valve Switch to the “AIR” position. The unit The engine idle and full speed settings are set and should speed up and then unload (and sealed at the factory, and should not be adjusted.
Page 35
SECTION 6 - - MAINTENANCE COMPRESSOR OIL LEVEL CAUTION The oil level should be checked before the unit is started. Always check the oil level while the unit is level, the engine off, and there is zero pressure in the Any unauthorized modification or failure to maintain this equipment may make it unsafe and out of factory separator tank.
Page 36
NOTE: To prevent damage to the element, never To service the air cleaners on all units proceed as fol- exceed a maximum air pressure of 100 psi (700 lows: kPa). Loosen outer wing nut and remove with cover. In the event the element is contaminated with dry dirt, Remove Element.
Page 37
FUEL TANK Premature wear of both the engine and compressor is ASSURED whenever dust--laden air is permitted to CLEAN fuel in the fuel tanks is vitally important and enter the engine’s combustion chamber or the every precaution should be taken to ensure that only compressor intake.
Page 38
COMPRESSOR OIL COOLER WARNING The compressor lubricating and cooling oil is cooled by means of the fin and tube--type oil cooler, located High pressure air can cause severe injury or death beside the radiator. The lubricating and cooling oil, from hot oil and flying parts. Always relieve flowing internally through the core section, is cooled by pressure before removing caps, plugs, covers or...
Page 39
COMPRESSOR OIL The lubricating and cooling oil must be replaced every 500 hours of operation or six (6) months, whichever comes first. RECEIVER- -SEPARATOR SYSTEMS WARNING High pressure air can cause severe injury or death from hot oil and flying parts. Always relieve pressure before removing caps, plugs, covers or other parts from pressurized air system.
Page 40
S Place a straightedge across top of element and mea- The life of the oil separator element is dependent upon sure from bottom of straightedge to bottom of ele- the operating environment (soot, dust, etc.) ment (See Fig. 4.1). should be replaced every twelve months or 2000 hours.
Page 41
SCAVENGE LINE 3. If the paint has faded or chalked, the use of a commercial grade, non- -abrasive car wax may WARNING partially restore the color and gloss. Field Repair of Texture Paint High pressure air can cause severe injury or death from hot oil and flying parts.
Page 42
MAINTENANCE SCHEDULE These time periods should be reduced if operating in extreme conditions (very hot, cold, dusty or wet). Daily Weekly Monthly 3 MOS . 6 MOS. 12 MOS. SMALL UNITS (P100- - P600) 250 hours 500 hours 1000 hours LARGE UNITS (HP600- - P1600) 500 hours 1000 hours...
Page 43
SECTION 7 - - LUBRICATION GENERAL INFORMATION Lubrication is an essential part of preventive mainte- If the unit has been operated for the time/ hours men- nance, affecting to a great extent the useful life of the tioned above, it should be completely drained of oil. If unit.
Page 44
Portable Compressor Fluid Chart Refer to these charts for correct compressor fluid RATED OPERATING PRESSURE required. Note that the selection of fluid is dependent on 350 PSI 100 - - 300 PSI the design operating pressure of the machine and the 125_F ambient temperature expected to be encountered 50_C...
Page 45
SECTION 8 - - Trouble Shooting INTRODUCTION B. Do The Simplest Things First Trouble shooting for a portable air compressor Most troubles are simple and easily corrected. is an organized study of a particular problem or example, most complaints are “low capacity” which may series of problems and a planned method of be caused by too low an engine speed or “compressor procedure for investigation and correction.
Page 46
TROUBLE SHOOTING CHART Bold Headings depict the COMPLAINT - - Subheadings suggest the CAUSE Note: Subheadings suggest sequence to follow troubleshooting. Corrective Action Unit Shutdown: Out of Fuel Add CLEAN diesel Fuel Compressor Oil Temp. Too High See Complaint 10 Engine Water Temp.
Page 47
Engine Oil Pressure Lamp Stays On: Corrective Action Low Oil Level Add oil. Out of Level >15 degrees Relocate or reposition. Wrong Lube Oil See Engine Oil Spec. Change oil. Clogged Oil Filter Element(s) Replace element(s). Engine Malfunctioning See Trouble Shooting in Engine Manual. Loose Wire Connection.
Page 48
Excessive Compressor Oil Temperature: Corrective Action Ambient Temp. > 125_F (52_C) Above spec limit. Out of Level > 15 degrees Relocate or reposition unit. Low Oil Level Add oil. Look for any leaks. Wrong Lube Oil Check spec in this manual. Dirty Cooler Clean exterior surfaces.
Page 49
Short Air Cleaner Life: Corrective Action Dirty Operating Conditions Move unit to cleaner environment. Inadequate Element Cleaning Install new element. Incorrect Stopping Procedure Read procedure in this manual. Wrong Air Filter Element Install proper element. Oil Pump Drive Coupling Inspect coupling. If necessary, replace coupling. Excessive Oil In Air: High Oil Level Read procedure in this manual.
Page 50
SECTION 9 - - PARTS ORDERING location relative to the other parts in the assembly. GENERAL The part number, the description of the part and the quantity of parts required are shown on each This publication, which contains an illustrated parts illustration or on adjacent page.
Page 51
MARKINGS AND DECALS Always specify the number of the parts list pub- NOTICE lication. Do not paint over safety warnings or instructional decals. If safety warning decals become illegible, Always specify the quantity of parts required. immediately order replacements from the factory. Always specify the part number, as well as the Part numbers for original individual decals and their description of the part, or parts, exactly as it is...
Page 52
Warranty: The Company warrants that parts man- Limitation of Liability: ufactured by it will be as specified and will be free from The remedies of the Purchaser set forth herein are ex- defects in materials and workmanship. The Compa- clusive, and the total liability of the Company with re- ny’s liability under this warranty shall be limited to the spect to this order whether based on contract, warran- repair or replacement of any part which was defective...
Page 53
AIREND EXCHANGE PROGRAM Your nearest sales office, autonomous company or Your Ingersoll--Rand Company Construction Equip- authorized distributor must first contact the Parts Ser- ment Group Sales Offices and authorized distributors vice Department at the factory at which your portable as well as Ingersoll--Rand International autonomous air compressor was manufactured for an airend ex- companies and authorized distributors now change number.
Page 54
PARTS LIST CONTENTS Frame Complete Engine Complete Cooling Complete Oil By--pass Vlv Complete Airend Complete Airend Assembly Air Service Complete Seperator Tank Complete Central Drains Air Intake Complete Air Cleaner Assembly Fuel Tank Complete Remote Filters Complete Air and Oil Piping Air and Oil Piping Instrument Panel Battery Assembly...
Page 55
A2 S INGERSOLL- -RAND COMPANY PORTABLE COMPRESSOR DIVISION DATE/DWN BY: DESCRIPTION 4/25/97 FRAME COMPLETE MODEL NO. DATE/REV: MANUAL NO. 4/98 P--130AWJDU -- 35393065--02 P--185AWJDU Book 35393065 (2/02) - - 54 - -...
Page 56
ITEM C.P.N. DESCRIPTION FRAME 36890457 CORNER, VERT CURB CAB 36890499 CORNER, VERT CURB BED 36890507 FRAME, DOOR LOWER 36890564 36890556 FRAME, DOOR LOWER 36890671 FRAME, DOOR UPPER 36890663 FRAME, DOOR UPPER 36890606 DOOR, STREET 36890598 DOOR, CURB SIDE 36890630 BRACKET, A/E OIL FILTER BRACKET, ENG OIL/FUEL 36890622 36890614...
Page 57
INSTRUMENT PANEL (P130, P175) (P185) A2 A3 A4 A5 A6 A2 A3 A4 (ON 185) (ON 130, 175) INGERSOLL- -RAND COMPANY PORTABLE COMPRESSOR DIVISION DATE/DWN BY: DESCRIPTION ENGINE COMPLETE 4/25/97 MODEL NO. DATE/REV: MANUAL NO. 4/98 P--130AWJDU -- 35393065--04 P--185AWJDU Book 35393065 (2/02) - - 56 - -...
Page 58
ITEM C.P.N. DESCRIPTION 36889764 ENGINE 3 CYL. (P130, P175) {PRIOR TO S/N 295999} 36889756 ENGINE 4 CYL. (P185) 36920015 ENGINE 4 CYL. (P185) {BEGIN WITH S/N 295999} {PRIOR TO S/N 308296} 36888030 BRACKET, FRONT ENGINE 54438643 BRACKET, FRONT ENGINE {BEGIN WITH S/N 308296} {PRIOR TO S/N 308296} 36890044 BRACKET, REAR ENGINE...
Page 61
OIL TEMPERATURE BYPASS VALVE ASSEMBLY 36884179 INGERSOLL- -RAND COMPANY PORTABLE COMPRESSOR DIVISION DATE/DWN BY: DESCRIPTION OIL TEMP BYPASS VALVE 5/09/97 MODEL NO. DATE/REV: MANUAL NO. 4/98 P--130WJDU 35393065--08 P--185WJDU Book 35393065 (2/02) - - 60 - -...
Page 62
ITEM C.P.N. DESCRIPTION 36776714 BODY 35584242 GASKET 36788289 BODY 36765832 COVER 36782019 ELEMENT 95022307 O--RING 36786382 SCREW 35288448 BALL 35379940 SPRING 36788164 PLUG 36788172 SEAL 36884187 SCREW, HEX M08--125 X 80 OIL TEMPERATURE BYPASS VALVE ASSEMBLY 36884179 INGERSOLL- -RAND COMPANY PORTABLE COMPRESSOR DIVISION DATE/DWN BY: DESCRIPTION...
Page 63
FRONT P130 ONLY P175 - - P185 ONLY BEGIN WITH SERIAL NUMBER 326650 INGERSOLL- -RAND COMPANY PORTABLE COMPRESSOR DIVISION DATE/DWN BY: DESCRIPTION 6/18/96 AIREND COMPLETE MODEL NO. DATE/REV: MANUAL NO. 2/02 35393065--10 Book 35393065 (2/02) - - 62 - -...
Page 64
ITEM C.P.N. DESCRIPTION 95055307 SCREW, CAP SOC HD 3/8--16 X 2 35329887 DRIVER, COUPLING 3/8 36865012 COUPLING, DRIVE 36769289 36880995 SCREW, HEX FLANGE HD M10--1.5 X 30 54755087 COUPLING 54755111 BEARING, HEX 95065637 SCREW, SOCKET SET 3/8--16 X 1/4 36881704 SCREW, HEX FLANGE HD 3/8--16 X 1.25 INGERSOLL- -RAND COMPANY PORTABLE COMPRESSOR DIVISION...
Page 65
* NEW P- -175 AIREND ASSEMBLY 42430926 * NEW P- -185 AIREND ASSEMBLY 42430926 INGERSOLL- -RAND COMPANY PORTABLE COMPRESSOR DIVISION DATE/DWN BY: DESCRIPTION AIREND ASSEMBLY 5/09/97 MODEL NO. DATE/REV: MANUAL NO. 4/98 35393065--12 P130WJDU P185WJDU Book 35393065 (2/02) - - 64 - -...
Page 66
5/09/97 FACTORY REBUILT AIREND THE ONLY COST EFFECTIVE OPTION. CALL YOUR LOCAL IR DATE/REV: MODEL NO. MANUAL NO. DEALER FOR MORE DETAILS. PLEASE PROVIDE YOUR AIREND SERIAL NUMBER. 35393065--13 5/99 P130WJDU P185WJDU Book 35393065 (2/02) - - 65 - -...
Page 67
INGERSOLL- -RAND COMPANY PORTABLE COMPRESSOR DIVISION DATE/DWN BY: DESCRIPTION 5/12/97 AIR SERVICE COMPLETE DATE/REV: MODEL NO. MANUAL NO. P--130AWJDU -- 35393065--14 4/98 P--185AWJDU Book 35393065 (2/02) - - 66 - -...
Page 68
ITEM C.P.N. DESCRIPTION 36891505 TUBE, SERVICE 95219861 ELBOW, TUBE 35114545 TEE, STREET 1/4 NPT 95048914 NIPPLE, 1/4NPT 35324839 VALVE, BALL 35322379 VALVE, BLOWDOWN 36766772 ORIFICE, MUFFLER .062 {PRIOR TO S/N 305271} 35608009 NOZZLE, .319 SONIC (P130) 36923910 NOZZLE, .319 SONIC ORIFICE (P130) {BEGIN WITH S/N 305271} 35608025 NOZZLE, .378 SONIC (P175)
Page 99
A8 A5 (82.25”) R (65”) B4 B5 INGERSOLL- -RAND COMPANY PORTABLE COMPRESSOR DIVISION DATE/DWN BY: DESCRIPTION ENCLOSURE COMPLETE 6/13/97 MODEL NO. DATE/REV: MANUAL NO. 2/02 P--130AWJDU -- 35393065--40 P--185AWJDU Book 35393065 (2/02) - - 98 - -...
Page 100
ITEM C.P.N. DESCRIPTION STRINGER, CAB SIDE 36890531 STRINGER, BED SIDE 36890549 PANEL, ROOF CLR END 36890762 CHANNEL, ROOF CONNECTOR 36891414 PANEL, ROOF (P130, P175) 36890838 PANEL, ROOF (P185) 36890754 PANEL, UPPER ENG BED 36890739 PANEL, LWR ENG BED 36890721 36890812 BOX, AIR INLET BED PANEL, FILTER END BED 36890747...
Page 102
ITEM C.P.N. DESCRIPTION 36892735 PANEL, ACOUSTIC ST DOOR 36892792 PANEL, ACOUSTIC CRB DOOR 36892875 PANEL, ACOUSTIC CAB SPLTR 36892867 PANEL, ACOUSTIC BED SPLTR BOT 36892859 PANEL, ACOUSTIC BED SPLTR TOP 36892743 PANEL, ACOUSTIC CAB COOLER 36892750 PANEL, ACOUSTIC CAB LWR ENG 36892768 PANEL, ACOUSTIC CAB UPPER ENG 36892784...
Page 103
WARNING WARNING Improper operation of this equipment. Can cause serious injury or death. Read Operator’s Manual supplied with Hot pressurized fluid. this machine before operation or Can cause serious burns. servicing. Modification or alteration of this machine. Do not open radiator while Can cause serious injury or death.
Page 104
ITEM C.P.N. DESCRIPTION DECAL, ROTATING FAN 54568779 DECAL, HOT PRESS FLUID 54568761 DECAL, COMBINATION 3--PART 54629902 DECAL, EIT AT WORK 36505816 54568787 DECAL, IMPROPER OPERATION 36514602 DECAL, NOISE EMISSION INGERSOLL- -RAND COMPANY PORTABLE COMPRESSOR DIVISION DATE/DWN BY: DESCRIPTION 6/18/97 DECAL LOCATION MODEL NO.
Page 105
WARNING Combustible gas. Can cause serious burns, blindness or death. WARNING Keep sparks and open High pressure air. flames away from batteries. Can cause serious injury or death. 54568753 REV. A Relieve pressure before removing filler plugs/caps, INGERSOLL- -RAND COMPANY fittings or covers.
Page 106
ITEM C.P.N. DESCRIPTION DECAL, OPERATING INSTRUCTIONS 36879054 CARD, UTILITY SAFETY 36531143 TIE, PUSH--MT 36847861 DECAL, BATTERY GAS 54568753 54604970 DECAL, OIL FILL 54568795 DECAL, HIGH PRESSURE AIR 36531150 DECAL, GENERAL DATA 36523306 PLATE, SERIAL NUMBER 36794816 RIVET 54629977 DECAL, CENTRAL DRAINS DECAL, WIRING DIAGRAM 36531168 PRIOR TO SERIAL NUMBER 326650...
Page 107
WARNING Combustible gas. WARNING Can cause serious burns, blindness or death. High pressure air. Can cause serious injury Keep sparks and open or death. flames away from batteries. BEGIN WITH SERIAL NUMBER 326650 Relieve pressure before 54568753 REV. A removing filler plugs/caps, INGERSOLL- -RAND COMPANY fittings or covers.
Page 108
ITEM C.P.N. DESCRIPTION DECAL, OPERATING INSTRUCTIONS 22099311 CARD, STANDARD WIRING 22108617 CARD, OPTION WIRING 22108641 DECAL, BATTERY GAS 54568753 54604970 DECAL, OIL FILL 54568795 DECAL, HIGH PRESSURE AIR 54629977 DECAL, CENTRAL DRAINS 36523306 PLATE, SERIAL NUMBER 36794816 RIVET BEGIN WITH SERIAL NUMBER 326650 INGERSOLL- -RAND COMPANY PORTABLE COMPRESSOR DIVISION DATE/DWN BY:...
Page 109
RETURN PICKUP WARNING Rotating fan blade. Can cause serious injury. Do not operate without guard in place. 54568779 REV. A PRIOR TO SERIAL NUMBER 326650 INGERSOLL- -RAND COMPANY PORTABLE COMPRESSOR DIVISION DATE/DWN BY: DESCRIPTION 6/18/97 DECAL LOCATION MODEL NO. DATE/REV: MANUAL NO.
Page 110
ITEM C.P.N. DESCRIPTION DECAL, ROTATING FAN 54568779 DECAL, PRESS REG ADJ INST (P130 ONLY) 36529394 DECAL, SPD & PRESS REG (P175, P185 ONLY) 36529451 DECAL, RAD FILL HOT 54604962 54625207 DECAL, DIESEL FUEL PRIOR TO SERIAL NUMBER 326650 INGERSOLL- -RAND COMPANY PORTABLE COMPRESSOR DIVISION DATE/DWN BY: DESCRIPTION...
Page 111
RETURN PICKUP WARNING Rotating fan blade. Can cause serious injury. Do not operate without guard in place. 54568779 REV. A BEGIN WITH SERIAL NUMBER 326650 INGERSOLL- -RAND COMPANY PORTABLE COMPRESSOR DIVISION DATE/DWN BY: DESCRIPTION 6/18/97 DECAL LOCATION MODEL NO. DATE/REV: MANUAL NO.
Page 112
ITEM C.P.N. DESCRIPTION DECAL, ROTATING FAN 54568779 DECAL, RAD FILL HOT 54604962 DECAL, DIESEL FUEL 54625207 BEGIN WITH SERIAL NUMBER 326650 INGERSOLL- -RAND COMPANY PORTABLE COMPRESSOR DIVISION DATE/DWN BY: DESCRIPTION 6/18/97 DECAL LOCATION MODEL NO. DATE/REV: MANUAL NO. 12/00 P--130AWJDU -- 35393065--49 P--185AWJDU Book 35393065 (2/02)
Page 113
SECTION 11 - - OPTIONS LIST Cold Start, Auto JD Cold Start, Manual Diagnostic Module Gauge, Tachometer Generator Assembly Side Hinge Hose Reel Assembly Indicator, Electric Air Filter Indicator, Separator Delta Valve, Minimum Pressure Valve Assembly, Minimum Pressure Valve, Electric Start Run Schematic, Cold Start Wiring Schematic, Generator Wiring Schematic, Hose Reel Wiring...
Page 114
35393065--02 INGERSOLL- -RAND COMPANY PORTABLE COMPRESSOR DIVISION 35393628--02 DATE/DWN BY: DESCRIPTION AUTO COLD START (JD) 8/01/97 DATE/REV: MODEL NO. MANUAL NO. 4/98 OPTION Book 35393065 (1/01) - - 107 - -...
Page 115
ITEM C.P.N. DESCRIPTION KIT, COLD START 35377266 36796910 CYLINDER, ETHER 96701479 SCREW, HEX M10--1.5 X 16 36889384 BUSHING * SEE WIRING SCHEMATIC FOR COLD START KIT 35393065--03 INGERSOLL- -RAND COMPANY PORTABLE COMPRESSOR DIVISION 35393628--03 DATE/DWN BY: DESCRIPTION AUTO COLD START (JD) 8/01/97 DATE/REV: MODEL NO.
Page 116
ETHER 35393065--04 INGERSOLL- -RAND COMPANY PORTABLE COMPRESSOR DIVISION 35393628--04 DATE/DWN BY: DESCRIPTION MAN COLD START OPT 8/01/97 DATE/REV: MODEL NO. MANUAL NO. 4/98 OPTION Book 35393065 (1/01) - - 109 - -...
Page 140
NOTE: 1. WIRE FUSE INTO CIRCUIT AS CLOSE TO M (MOTOR) TERMINAL AS POSSIBLE. 2. NOT FOR USE WITH INGERSOLL ENGINES. TO START SWITCH PRESSURIZED FLUID CYLINDER DIESELMATIC VALVE BLACK LEAD TO BATTERY SOLENOID SWITCH E.T.S. SWITCH FUSE NOZZLE BLOCKOR VALVE CRANKING MOTOR NYLON TUBING COLD START WIRING FOR KIT 35377266...
Page 141
1 INSTALLATION OF PMVR 120 REGULATOR: A. CONNECT DOUBLE BRN WIRE LEADS OF VOLTAGE REGULATOR AS FOLLOWS: ONE LEAD TO SILVER SCREW OF DOUBLE RECEPTACLE IN CONTROL BOX. OTHER LEAD TO BRASS SCREW. CONNECT RED WIRE TO YELLOW WIRE (HOT +12 V SOURCE), AND TO PILOT LAMP TERMINAL.
Page 142
CIRCUIT BREAKER 16 RED(5) 10 RED(2) 10 RED(1) SPST SWITCH FURNISHED W/ HOSEREEL W/ YELLOW WIRE UNIT RELAY 16 WHT(6) SOLENOID FURNISHED W/ HOSEREEL 10 BLK(4) HOSEREEL MOTOR HOSE REEL WIRING FOR ELECTRIC HOSE REEL OPTION 35393065--30 INGERSOLL- -RAND COMPANY PORTABLE COMPRESSOR DIVISION 35393628--30 DATE/DWN BY:...
Page 143
C.P.N. DESCRIPTION 35610500 SPARK ARRESTOR (J DEERE) 36897296 ELBOW, EXHAUST 35314939 SWITCH, AIR RESTRICTION INDICATOR (ON AIR FILTERS) 95916243 COUPLING, 1/8 NPT X 13/16 9593493 NIPPLE, CLOSED 1/8 NPT X 3/4 36843563 ENGINE BLOCK HEATER (3 CYL. J DEERE) 35379221 ENGINE BLOCK HEATER (4 CYL.
Page 144
RETURN PICKUP 35393065--32 INGERSOLL- -RAND COMPANY PORTABLE COMPRESSOR DIVISION 35393628--32 DATE/DWN BY: DESCRIPTION 12/1/97 CENTRAL DRAINS w/ VALVES DATE/REV: MODEL NO. MANUAL NO. 4/98 P--130AWJDU -- OPTION P--185AWJDU Book 35393065 (1/01) - - 137 - -...
Need help?
Do you have a question about the P130WJDU and is the answer not in the manual?
Questions and answers