Pulsar PSB1552455 Quick Start Manual

Psb 27,6v/5,5a enclosed switch mode buffer power supply

Advertisement

Quick Links

DC 27,6V/5,5A uninterruptible power supply
wide AC input voltage range 176÷264V
high efficiency 84%
controlling of battery charging and maintaining
protecting of battery against excessive
discharging (UVP)
battery charging current 0,5A/2A,
changed by jumper

1. Technical description.

1.1. General description.

Buffer-type power supply units are intended for continuous power supply to devices that require stabilised voltage
of 24 V DC (+/-15%). The power supply provides a voltage of U=27,6 V DC with an output current of:
In case of power voltage decay, prompt switching to battery supply occurs. The power supply has the following
protections: short-circuit (SCP), overload (OLP), and overvoltage (OVP).

1.2. Technical parameters.

Supply voltage
Current consumption
Supply power
Efficiency
Output voltage
Output current
Output current t
AMB
Output current t
AMB
Voltage adjustment range
Ripple voltage
Battery charging current
Short-circuit protection SCP
Overload protection (battery) OLP
Overvoltage protection OVP
Excessive discharge protection UVP
Optical signalisation
Output of optical signalization
Operation conditions
Dimensions (LxWxH)
Features of the power supply:
1. Output current of 5A + 0,5A battery charging.
2. Output current of 3,5A + 2A battery charging.
Total device current + battery: 5,5A max.
<30° C
=40° C
PSB1552455
PSB 27,6V/5,5A enclosed switch
mode buffer power supply
Edition: 1 z from 17.11.2011
Supercedes edition: ....................
battery output is full protected against short-
circuit and reverse connection
LED optical signalisation
protections:
176÷264V AC 50÷60Hz
1,4A@230VAC max.
155W max.
84%
27,6V DC – buffer operation
19V÷27,6V DC – battery operation
5,0A + 0,5A battery charging
3,5A + 2A battery charging
5A + 0,5A battery charging - refer to graph 1 .
3,5 A + 2A battery charging - refer to graph 1.
3,3 A + 0,5A battery charging - refer to grap h 1.
1,8 A + 2A battery charging - refer to graph 1.
24÷28V DC
150mV p-p max.
0,5A max. or 2A max.
electronic
polymer fuse (PTC)
U>115% ÷ 150% of the output voltage, isolation of the
output voltage, atomatic recovery
U<19 V (± 5%) – disconnection of battery
green LED- presence of AC voltage
LED AC- presence of AC voltage
LED DC- presence of DC voltage on power supply output
2-nd enviromental class, temperature: -10
relative humidity 20%...90%, without condensation
199 x110 x 50 [mm]
1
SCP short-circuit protection
OVP overvoltage protection
overvoltage protection (output AC)
overload (OLP)
o
C÷40
EN
o
C

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PSB1552455 and is the answer not in the manual?

Questions and answers

Summary of Contents for Pulsar PSB1552455

  • Page 1 PSB1552455 PSB 27,6V/5,5A enclosed switch mode buffer power supply Edition: 1 z from 17.11.2011 Supercedes edition: ……………….. Features of the power supply: • • DC 27,6V/5,5A uninterruptible power supply battery output is full protected against short- • circuit and reverse connection wide AC input voltage range 176÷264V...
  • Page 2 Net/gross weight 0,76kg / 0,82kg Protection class PN-EN 60950-1:2007 I (first) - requires a protective conductor (PE) power-supply: Φ0,63÷2,5 I/O PCB : Φ0,41÷1,63 battery output BAT: 6,3F-2,5/40cm, Connectors output of optical signalization: plug 3-pin 5 mm Electrical strength of insulation: - between input (network) circuit and output circuits of power-supply (I/P-O/P) 3000 V/AC min.
  • Page 3 Battery terminal- negative (-) Fig 1. Description of terminals. Connector of optical signalization 2.4. Dimensions and fitting of the PSB1552455 power supply. Fig. 2. Dimensions of power supply. 3. Maintenance. All maintenance procedures can be performed after the disconnection of the power supply from the electrical grid.
  • Page 4 GENERAL WARRANTY CONDITIONS 1. Pulsar K. Bogusz Sp.j. (manufacturer) grants a two-year quality warranty for the equipment, starting from the date of purchase placed on the purchase order. 2. Should such purchase order be missing when the claim is submitted, the three-year guarantee period is counted from the date of the manufacturing of the device.

Table of Contents