Subscribe to Our Youtube Channel
Summary of Contents for Great Wall X240
- Page 1 Keyless Entry and Immobilizer Programming Methods Part Numbers and Component Identification X240 X200 V240 V200 SA220...
- Page 2 X240 Hover (Pre Facelift) - Components………………………………………..Page 4 X240 Hover (Pre Facelift) - Keyless entry programming……………………..Page 5 X200 and X240 Haval H5 - Components……………………………….…………Page 6 X200 and X240 Haval H5 - Keyless entry programming……………………..Page 7 - Components………………………………………….Page 8 V240 and V200 Wingle - Keyless entry programming………………………...Page 9...
- Page 3 X431 Navigation Chart Vehicle Model System System Variant X240 (Facelift) Haval H5 Engine Delphi MI 20U2_EOBD ECU CC6461KM39 Bosch ABS Bosch SRS System Delphi-BCM Immobilizer System Delphi Gas Immobilizer system X200 Haval H5 Engine K5 (N2)-ECM CC6461KM77 (Manual) K5 (N2)-ABS...
- Page 4 X240 (Hover) Components (PreFace Lift) Central locking Immobilizer Immobilizer Key Blank (For remote) Key Blank (Without remote) remote controller controller Transponder Module 3787100A-K00 3787400-V08 X240 3704015-K00-D1 3704015A-K00 3605110-K00 3605130-K00 3787100-K00-D1 3787200-V08 Please Note: When ordering Key and Remote parts all part numbers come separate from each other.
- Page 5 X240 (Hover) Programming (PreFace Lift) For the Module 3787100A-K00 and 3787100-K00-D1 (Vendor Code VA-873D1) 1. Open the Drivers front door and insert the key into the ignition. 2. Turn the key from Off to ON 5 times finishing in the ON position.
- Page 6 N/A (Controlled by BCM) 3605110-K00 3605130-K00 X200 3704010XK02XA 3704030XK02XA Note: • Remote Programming on Face lift X240 and X200 is performed using the X431 Scan Tool. • Version 33 or above is required for successful communication with the BCM. 3605130-K00 3704800XK80XA 3704010XK02XA 3605110-K00...
- Page 7 NOTE: - When the X431 displays “learning the second key…..” for another key remote to be Matched Some early versions of the X431 software and some early X240 vehicles will require you to press the home button to exit the “Key Teach” function once the first key has been completed otherwise you may delete the first remote.
- Page 8 V240 and V200 (Wingle) Components Immobilizer Immobilizer Central locking controller Key Blank (For remote) Key Blank (Without remote) remote controller Transponder Module V240 3787100-P00-C1 3787200-V08 3605110-K00 3605130-P00 3704140-P00-B3 3704140A-P00 3787100-P00 V200 3787100AP00XB 3787400-V08 3787100-P00-C1 3787100AP00XB 3605110-K00 3787100-P00 3787200-V08 3787400-V08 3704140A-P00 3704140-P00-B3...
- Page 9 V240 and V200 (Wingle) Programming V240 pre Facelift (Wingle 3) 1. Open the Drivers front door and insert the key into the ignition. 2. Turn the key from Off to ON 5 times finishing in the ON position. 3. The flashers will flash once to indicate programming mode has been entered. 4.
- Page 10 SA220 (Sailor) Components Central locking Immobilizer Key Blank (For remote) Key Blank (Without remote) remote controller controller Transponder SA220 3791500-02B-B2 3704140-P00-B3 3704012-B00 3787200-V08 Not Fitted 3704012-B00 3791500-02B-B2 Please Note: The key above without the remote 3704012-B00 can be substituted with either 3704140-P00- B3 (V240 for remote) or 3704140A- P00 (V240 without remote) 3704140-P00-B3...
- Page 11 SA220 (Sailor) Programming Method “A” Procedure A 1. Remove the LHF kick panel to gain access to the Central Locking controller. 2. Refer to the diagram below and earth out pin 9 three times (the door locks will cycle during this process). 3.
- Page 12 SA220 (Sailor) Programming Method “B” Procedure B 1. Remove the LHF kick panel to gain access to the Central Locking controller. 2. Ensure all the doors are in an unlocked state. 3. Refer to the diagram below and earth out pin 9 of the controller. 4.
- Page 13 How to Swap or Replace an ECU or Immobilizer Unit X240 and V240 (All Models) Can be Replaced or Swapped SA220 Can be Replaced or Swapped V200 & X200 CANNOT be swapped from another vehicle. Can be Replaced with a new unit from Parts.
- Page 14 Swapping an ECU from one car to another (Petrol Vehicles ONLY) 1. Connect the X431 to the Donor vehicle. 2. Navigate to the correct model and then to the “Immobilizer system” 3. Select “Delphi Gas Immobilizer system 4. Select “Immobilizer matching function” 5.
- Page 15 Replacing an ECU with a New unit (Petrol Only). 1. Connect the X431 to the vehicle and turn the ignition ON.. 2. Navigate to the correct model and then to the “Immobilizer system” 3. Select “Immobilizer system” 4. Select “Delphi Gas Immobilizer system” 5.
- Page 16 Swapping an Immobilizer from one car to another 1. Connect the X431 to the Donor vehicle. 2. Navigate to the correct model and then to the “Immobilizer system” 3. Select “Delphi Gas Immobilizer system” for a Petrol vehicle 4. Select “Delphie Diesel (Delphie 4D20) Immobilizer system“ for a Diesel. 5.
- Page 17 Replacing an Immobiliser Unit 1. Connect X431 to the vehicle and turn the ignition to ON. 2. Navigate to the correct model and then to the “Immobilizer system” 3. Select “Delphi Gas Immobilizer system” for a Petrol vehicle 4. Select “Delphi Diesel (Delphie 4D20) Immobilizer system“ for a Diesel. 5.
- Page 18 2. Select the correct vehicle and select “immobilizer system” 3. Select the correct system, X240 (Pre-Facelift) Haval H3 – Delphi Gas immobilizer system X240 (Face Lift) - Haval H5 - Delphi Gas immobilizer system - Haval H5 – X200 Delphi Diesel (Delphi 4D20) immobilizer system...
Need help?
Do you have a question about the X240 and is the answer not in the manual?
Questions and answers