Chrysler 2006 Sebring Convertible Owner's Manual
  1. Manuals
  2. Brands
  3. Chrysler Manuals
  4. Automobile
  5. Sebring Convertible 2006
  6. Owner's manual

Chrysler 2006 Sebring Convertible Owner's Manual

Chrysler new vehicle instrution manual
Hide thumbs Also See for 2006 Sebring Convertible:
Table of Contents

Advertisement

Quick Links

SECTION
1

INTRODUCTION

2
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
3
4
5
6
7
8
9
10
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
INDEX

TABLE OF CONTENTS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261
. . . . . . . . . . . . . . . . . . . . . . . . . . . 7
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279
PAGE
1
2
3
4
5
6
7
8
9
10

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 2006 Sebring Convertible and is the answer not in the manual?

Questions and answers

Related Manuals for Chrysler 2006 Sebring Convertible

Summary of Contents for Chrysler 2006 Sebring Convertible

  • Page 1: Table Of Contents

    TABLE OF CONTENTS SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
  • Page 3 CONTENTS Introduction ......4 How To Use This Manual ....4 Warnings And Cautions .

  • Page 4: Introduction

    4 INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully.
  • Page 5 INTRODUCTION 5...

  • Page 6: Warnings And Cautions

    This number also ap- pears on the Automobile Information Disclosure Label affixed to a window on your vehicle. Save this label as a convenient record of your vehicle identification number and optional equipment.

  • Page 7: Things To Know Before Starting Your Vehicle

    THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....9 Ignition Key Removal ....9 Automatic Transaxle Ignition Interlock System .
  • Page 8 8 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information ....18 Transmitter Battery Service ....18 Vehicle Theft Alarm .

  • Page 9: Things To Know Before Starting Your Vehicle 7

    A WORD ABOUT YOUR KEYS CAUTION! An unlocked car is an invitation to thieves. Always remove the key from the ignition, lock the doors, and close the windows when leaving the vehicle unat- tended. Ignition Key Removal Ignition Key Positions THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 9 Place the shift lever in PARK and make sure that the gearshift knob push button has returned to the out...

  • Page 10: Sentry Key - If Equipped

    10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SENTRY KEY — IF EQUIPPED With this system, an electronically coded ignition key sends a signal to the vehicle electronics. If the electronics recognizes the signal, the vehicle will start and continue to run.

  • Page 11: Replacement Keys

    Replacement Keys NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a Sentry Key has been programmed to a vehicle, it can not be programmed to any other vehicle. At the time of purchase, the original owner is provided with a four digit PIN number.

  • Page 12: Illuminated Entry System

    12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ILLUMINATED ENTRY SYSTEM The interior lights will come on when you open either door, unlock the vehicle with the remote keyless entry or central unlock from the driver’s side (if so equipped). They will remain on for about 30 seconds after all doors are closed then fade to off.
  • Page 13 Power Door Lock Switch If you press the door lock switch while the keys are in the ignition switch, and the driver’s door is open, the doors will not lock. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Door Lock Plunger If the door lock plunger is down when you shut the door, the door will lock.

  • Page 14: Central Locking-If Equipped

    14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Central Locking—If Equipped Turning the driver’s door lock to the unlock position twice within five seconds will unlock both doors. Turning the key in the driver’s door to the unlock position once will unlock only the driver’s door.

  • Page 15: Automatic Unlock On Exit-Only Available If Automatic Door Locks Are Enabled

    Power Door Lock Switch 4. A single chime will indicate the completion of the programming. Automatic Unlock on Exit—Only Available if Automatic Door Locks are Enabled This feature will unlock all the doors when the driver’s door is opened and the ignition switch is in the LOCK position.

  • Page 16: To Unlock The Doors

    16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To unlock the doors: Press and release the UNLOCK button once to unlock the driver’s door. Press the button twice within 5 seconds to unlock all doors. If your vehicle is equipped with Illumi- nated Entry, the interior lights also come on and remain on for about 30 seconds, when you unlock the doors.

  • Page 17: To Unlock The Trunk

    To unlock the trunk: Press and hold the Trunk button on the transmitter to unlatch the trunk. NOTE: The transmitter can be programmed to unlatch the trunk immediately upon activation of the Trunk button (without pressing and holding) by performing the following procedure: 1.

  • Page 18: General Information

    18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Press and release the Lock and Unlock buttons simul- taneously, followed by a press and release of ANY button on each new transmitter to be programmed as well as the original transmitter. You will hear a chime when a transmitter has been successfully programmed.

  • Page 19: Vehicle Theft Alarm

    2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch the battery, clean it with rubbing alcohol. 3. Reassemble the transmitter case. Snap the halves together and test transmitter operation. VEHICLE THEFT ALARM The system monitors the doors, trunk, and ignition for unauthorized operation.

  • Page 20: Trunk Lock And Release

    20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE TRUNK LOCK AND RELEASE Trunk Release Button Use the key or the Remote Keyless Entry Transmitter to open the trunk from outside the vehicle. From inside the car the trunk lid can be released by turning the ignition ON and depressing the Trunk Release Button located on the instrument panel to the left of the steering wheel.

  • Page 21: Trunk Internal Emergency Release

    Trunk Internal Emergency Release Emergency Release NOTE: As a security measure, a Trunk Internal Emer- gency Release lever is built into the trunk latching mechanism. In the event of an individual being locked inside the trunk, the trunk can be simply opened by pulling on the glow-in-the-dark handle attached to the trunk latching mechanism.

  • Page 22: Occupant Restraints

    22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The window controls on the driver’s door operate all windows. The driver’s window switch has an Auto Down feature. Press the window switch past the detent, release, and the window will go down automatically. To open the window part way, pull the window switch part way and release it when you want the window to stop.

  • Page 23: Lap/Shoulder Belts

    Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision which includes you. This can happen far away from home or on your own street. Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision.
  • Page 24 24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the front seat. Latch Plate 2. The seat belt latch plate is on the back of your seat. Grasp the latch plate and pull out the belt.
  • Page 25 WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury.

  • Page 26: Seat Belt Pretensioners

    26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen.

  • Page 27: Enhanced Driver Seat Belt Reminder System (Beltalert)

    The pretensioners are triggered by the front airbag con- trol module (see Airbag Section). Like the front airbags, the pretensioners are single use items. After a collision that is severe enough to deploy the airbags and preten- sioners, both must be replaced. Enhanced Driver Seat Belt Reminder System (BeltAlert) If the driver’s seat belt has not been buckled within 60...

  • Page 28: Seat Belts And Pregnant Women

    28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Turn off the engine. A single chime will sound to signify that you have successfully completed the pro- gramming. The Enhanced Warning System (BeltAlert) can be reacti- vated by repeating this procedure. NOTE: Although the Enhanced Warning System (BeltAlert) has been deactivated, the Seat Belt Warning...

  • Page 29: Driver And Right Front Passenger Supplemental Restraint System (Srs) - Airbag

    Driver and Right Front Passenger Supplemental Restraint System (SRS) - Airbag Front Airbag Components This vehicle has front airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s airbag is mounted in the center of the steering wheel.
  • Page 30 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The seat belts are designed to protect you in many types of collisions. The front airbags deploy only in moderate to severe frontal collisions. But even in collisions where the airbags work, you need the seat belts to keep you in the right position for the airbags to protect you properly.
  • Page 31 WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags.
  • Page 32 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE wheel and column. If the key is in the “off” position, in the ACC position, or not in the ignition, the airbags are not on and will not inflate. • The airbag control module also turns on the AIRBAG light in the instrument panel for 6 to 8 seconds when the ignition is first turned on, then turns the light off.
  • Page 33 NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system. If you do have a collision which deploys the airbags, any or all of the following may occur: •...

  • Page 34: Child Restraint

    34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbags are not there to protect you.
  • Page 35 Children 12 years and under should ride properly buck- led up in a rear seat. According to crash statistics, children are safer when properly restrained in the rear seat rather than in the front. WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle.
  • Page 36 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint.
  • Page 37 than one year. These child seats are also held in the vehicle by the lap/shoulder belt or the LATCH child restraint anchorage system. (See the LATCH — Child Seat Anchorage System Section.) The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly.
  • Page 38 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE connection to the top tether anchorages have been avail- able for some time. For some older child restraints, many child restraint manufacturers offer add-on tether strap kits or retro-fit kits. You are urged to take advantage of all the available attachments provided with your child re- straint in any vehicle.
  • Page 39 Installing the LATCH-Compatible Child Restraint System We urge that you carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here. Again, carefully follow the installation instructions that were provided with the child restraint system.
  • Page 40 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE installing the child restraint buckle the seat belt so the seat belt is tucked behind the child restraint and out of reach. If the buckled seat belt interferes with the child restraint installation, instead of tucking the seat belt behind the child restraint, route the seat belt through the child restraint belt path and then buckle it.
  • Page 41 To attach a child restraint tether strap: 1. Lift the carpet flap to expose the anchor directly behind the seat where you are placing the child restraint. Child Tether Anchor Location 2. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat.

  • Page 42: Engine Break-In Recommendations

    42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Transporting Pets Airbags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts.

  • Page 43: Safety Tips

    SAFETY TIPS Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO) follow the safety tips below. •...

  • Page 44: Periodic Safety Checks You Should Make Outside The Vehicle

    44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Defrosters Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. Periodic Safety Checks You Should Make Outside the Vehicle Tires Examine tires for excessive tread wear or uneven wear...
  • Page 45 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Convertible Top Operation ....47 To Lower The Top ..... .47 To Raise The Top .
  • Page 46 46 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Multi-Function Control Lever ....67 Headlights, Parking Lights, Instrument Panel Lights ......67 Automatic Headlights—If Equipped .

  • Page 47: Convertible Top Operation

    CONVERTIBLE TOP OPERATION WARNING! The convertible top does not provide the structural protection that a reinforced metal roof does, and the fabric top cannot be expected to prevent the ejection of the occupants of a vehicle in a collision. Therefore it is important that all occupants wear their seat belts at all times when riding in a convertible.

  • Page 48: 48 Understanding The Features Of Your Vehicle

    48 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Release the top from the windshield header by pulling both latch handles rearward until the latch hooks are free. Unlatching Convertible Top 4. Press the Power Top Switch to disengage the top pins from the header.

  • Page 49: To Raise The Top

    CAUTION! Damage to the top material could result if the latch handles are not completely closed when the top is lowered. The convertible top cover cannot be in- stalled while the latch handles are open. To Raise The Top: CAUTION! To avoid damage to the sunvisors, rotate the driver’s and passenger’s sunvisor to the forward (against glass) position before raising or lowering the con-...

  • Page 50: Top Cover Installation

    50 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Press the Power Top Switch to raise the top. Before the top reaches the windshield, open both front latch handles. Press the switch again to continue raising the top until the two pins seat themselves in the windshield header.
  • Page 51 Installation From Inside The Vehicle 1. Kneel on the rear seat and tuck the rear edge and side edges of the top cover under the black molding near the trunk. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 51 2. Insert both tabs located on the front of the top cover in between the seatback and seatback bracket.
  • Page 52 52 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Snap the top cover flaps to the inner trim panel snaps. The side of the seat back cushion hides the snap. Top Cover Flap 4. Press down on the forward portion of the top cover to engage the hook and loop fasteners.
  • Page 53 Installation From Outside The Vehicle 1. Start on one side of the vehicle and tuck as much of the top cover as possible under the black molding. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 53 2. Snap the top cover flap to the inner trim panel snap. (The side of the seat back cushion hides the snap.) Top Cover Flap...
  • Page 54 54 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Tuck the top cover tab closest to you into the space between the seatback and the seatback bracket. 4. Walk to the other side of the vehicle and finish tucking the top cover under the black molding. Insert the remain- ing tab between the seatback and the seatback bracket.

  • Page 55: Top Cover Removal

    6. Press down on the forward portion of the top cover to engage the hook and loop fasteners. Hook and Loop Fasteners Top Cover Removal Unsnap the snaps and disengage the hook and loop fasteners, slide the tabs from the rear seat and then from the rear of the top storage area.

  • Page 56: Mirrors

    56 UNDERSTANDING THE FEATURES OF YOUR VEHICLE passengers and a rear courtesy lamp located directly in back of the center console. The center console can be locked using the “master” key. Two coin holders are located toward the front of the inside of the console bin.

  • Page 57: Electric Remote-Control Mirrors

    Automatic Dimming Mirror CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 57 Electric Remote-Control Mirrors Both of the outside mirrors can be adjusted by using the remote controls mounted on the instrument panel located...

  • Page 58: Illuminated Vanity Mirrors

    58 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirror Adjustment — Driver’s Side Adjust the outside mirror to center on the adjacent lane of traffic, with a slight overlap of the view obtained on the inside mirror. Right Side Mirror Adjustment Adjust the convex outside mirror so you can just see the side of your vehicle in the part of the mirror closest to the vehicle.

  • Page 59: Seats

    SEATS Manual Front Seat Adjustments Forward/Rearward — If Equipped The adjusting bar is at the front of the seats, near the floor. Pull the bar up to move the seat to the desired position. Manual Seat Adjuster Using body pressure, move forward and rearward on the seat to be sure the seat adjusters have latched.

  • Page 60: Power Driver's Seat

    60 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured.

  • Page 61: Heated Seats - If Equipped

    CAUTION! Do not place any article under a power seat as it may cause damage to the seat controls. Heated Seats — If Equipped WARNING! Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater.

  • Page 62: To Fold The Front Seatback Forward

    62 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Fold The Front Seatback Forward: Turn the high mounted release lever rearward and fold the seatback forward. If you release the lever early, a safety feature locks the seat into that position. Turn the release lever again to continue lowering the seat.

  • Page 63: Adjustable Head Restraints

    Adjustable Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Adjust the restraints so that the upper edge is as high as practical. To raise, pull up on the head restraint. To lower, depress the button on the post guide and push down on the head restraint.

  • Page 64: Lights

    64 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Hood Safety Catch Use the hood prop rod to secure the hood in the open position. Place the upper end of the prop rod in the hole marked “prop” on the underside of the hood. To prevent possible damage, do not slam the hood to close it.

  • Page 65: Interior Lights

    UNDERSTANDING THE FEATURES OF YOUR VEHICLE 65 NOTE: The map lights will remain on until the mirror switches have been turned to the OFF position, so be sure that they have been turned off before leaving the vehicle. Interior Lights The console rear light, map/courtesy lights, and the optional under-door courtesy lights come on when a door is opened and the panel lamp dimmer switch...
  • Page 66 66 UNDERSTANDING THE FEATURES OF YOUR VEHICLE turn on the lights. Turn the panel dimmer switch fully clockwise to prevent the lights from coming on when a door is opened. NOTE: The interior lights have a “fade to off” feature. When the lights are turned off, they gradually “fade”...

  • Page 67: Multi-Function Control Lever

    Multi-Function Control Lever Multi-Function Lever The Multi-Function lever controls the operation of the headlights, turn signals, headlight beam select switch, instrument panel light dimming, passing light, dome light, and fog lights. Headlights, Parking Lights, Instrument Panel Lights Turn the end of the Multi-Function lever to the first detent for parking light operation.

  • Page 68: Automatic Headlights-If Equipped

    68 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Headlights—If Equipped This system automatically turns your headlights on at a preset level of outdoor lighting. Turn the end of the control lever to the third detent to turn the system on. When the system is on, the headlight delay feature is also on.

  • Page 69: Headlight Beam Select Switch

    Headlight Beam Select Switch Pull the turn signal lever towards you to switch the headlights to HIGH beam. Pull the turn signal lever a second time to switch the headlights to LOW beam. Flash to Pass You can signal another vehicle with your headlights by lightly pulling the turn signal lever toward the steering wheel.

  • Page 70: Mist

    70 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate for several cycles after the lever is released, and then resume the intermit- tent interval previously selected.

  • Page 71: Traction Control- If Equipped

    Tilt Steering Column Control WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped.

  • Page 72: Electronic Speed Control- If Equipped

    72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The Traction Control System is enabled each time the ignition switch is turned On. This will occur even if you used the switch to turn the system off before powering down or turning the ignition to Lock. ELECTRONIC SPEED CONTROL—...

  • Page 73: To Deactivate

    To Deactivate: A soft tap on the brake pedal, pushing the CANCEL button, or normal brake or clutch pressure will deactivate speed control without erasing the memory. Pushing the ON/OFF button or turning off the ignition turns the speed control system off and erases the memory. To Resume Speed: To resume a previously set speed, push and release the RESUME/ACCEL button.
  • Page 74 74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When Climbing A Hill If vehicle speed drops 3 mph (5 km/h) below the Speed Control set speed, the transaxle will downshift to third gear. Under severe conditions the transaxle may down- shift again to second gear. The transaxle will upshift to fourth gear after the vehicle has reached the top of the hill.

  • Page 75: Garage Door Opener - If Equipped

    GARAGE DOOR OPENER — IF EQUIPPED The HomeLink Universal Transceiver replaces up to three remote controls (hand held transmitters) that oper- ate devices such as garage door openers, motorized gates, or home lighting. It triggers these devices at the push of a button. The Universal Transceiver operates off your vehicle’s battery and charging system;...
  • Page 76 76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicle exhaust contains carbon monoxide, a danger- ous gas. Do not run the vehicle’s exhaust while training the transceiver. Exhaust gas can cause seri- ous injury or death. WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver.

  • Page 77: Rolling Code" Programming

    5. The indicator light in the Universal Transceiver will begin to flash, first slowly and then rapidly. The rapid flashing indicates successful programming. If after 90 seconds the indicator light does not flash rapidly or goes out, return to step 1 and repeat the procedure. To train the other buttons, repeat steps 3 and 4.

  • Page 78: Canadian Programming/Gate Programming

    78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE difficulty in locating the training button, check your garage door opener manual, or call 1-800-355-3515 or, on the Internet, at www.homelink.com. 2. Press and hold the training button on the garage door opener head unit This will activate the “training” light. NOTE: After completing step 2, you have 30 seconds to start step 3.

  • Page 79: Reprogramming A Single Button

    Reprogramming A Single Button 1. Press and hold the Universal Transceiver button to be reprogrammed. Do not release until step 4 has been completed. 2. When the indicator light begins to flash slowly (after 20 seconds) position the hand held transmitter one to three inches away from the button to be trained.
  • Page 80 80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Electrical Outlet Use With Engine Off • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.

  • Page 81: Understanding Your Instrument Panel

    UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instruments And Controls ....85 Instrument Cluster Standard ....86 Instrument Cluster Premium .
  • Page 82 82 UNDERSTANDING YOUR INSTRUMENT PANEL Seek Button (Radio Mode) ....101 Tuning ......101 Radio Data System (RDS) .
  • Page 83 CD Changer Control Capability — If Equipped ......108 Sales Code RBB—AM/FM Stereo Radio With Cassette Tape Player And CD Changer Capability .
  • Page 84 84 UNDERSTANDING YOUR INSTRUMENT PANEL Satellite Radio — If Equipped ... . . 123 System Activation ..... 123 Electronic Serial Number/Sirius Identification Number (ENS/SID) .

  • Page 85: Instruments And Controls

    UNDERSTANDING YOUR INSTRUMENT PANEL 85 INSTRUMENTS AND CONTROLS...

  • Page 86: Understanding Your Instrument Panel

    86 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER STANDARD...

  • Page 87: Instrument Cluster Premium

    UNDERSTANDING YOUR INSTRUMENT PANEL 87 INSTRUMENT CLUSTER PREMIUM...

  • Page 88: Instrument Cluster - Gtc Model

    88 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER – GTC MODEL...

  • Page 89: Instrument Cluster Description

    INSTRUMENT CLUSTER DESCRIPTION 1. Fuel Gauge When the ignition key is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. 2. Traction Control — If Equipped This display indicator illuminates momentarily as a bulb check when the ignition switch is first turned ON.
  • Page 90 90 UNDERSTANDING YOUR INSTRUMENT PANEL light stays on, or comes on while driving, have the system checked by an authorized dealer. (See page 72 for more information.) 5. Tachometer The red area of the scale shows the maximum permissible engine revolutions-per-minute (rpm x 1000) for each gear range.
  • Page 91 your Owner Manual for more details). If the bulb does not come on when turning the key from OFF to ON, have the condition checked promptly. Certain conditions such as a loose or missing gas cap or poor fuel quality may illuminate the light after engine start.
  • Page 92 92 UNDERSTANDING YOUR INSTRUMENT PANEL 14. Transmission Range Indicator This indicator illuminates to show the automatic trans- mission gear selection. An optional AutoStick Gear Indicator displays the current transaxle gear when in AutoStick mode. 15. Odometer/Trip Odometer The odometer shows the total distance the vehicle has been driven.
  • Page 93 17. Oil Pressure Light Shows low engine oil pressure. The light will come on and remain on briefly when the igni- tion is turned on as a bulb check. If the bulb does not come on during starting, have the bulb repaired promptly.
  • Page 94 94 UNDERSTANDING YOUR INSTRUMENT PANEL In an ABS equipped vehicle, the Brake System Warning light will come on if the ABS light is not functioning or if the ABS system is not communicating. 19. Seat Belt Reminder Light When the ignition switch is first turned ON, this light will turn on for 5 to 8 seconds as a bulb check.

  • Page 95: Compass, Temperature, And Trip Computer Display - If Equipped

    COMPASS, TEMPERATURE, AND TRIP COMPUTER DISPLAY — IF EQUIPPED Trip Computer Display This feature allows you to choose between a compass / temperature display and one of five trip conditions being monitored. Control Buttons Step Button Use this button to choose or cycle through the five trip conditions.

  • Page 96: Trip Conditions

    96 UNDERSTANDING YOUR INSTRUMENT PANEL Trip Conditions Average Fuel Economy (AVG ECO) This display shows the average fuel economy since the last reset. Estimated Range (DTE) This display shows the estimated distance that can be traveled with the fuel remaining in the tank. This esti- mated distance is based on the most recent trip informa- tion: (Average Fuel Economy) x (Fuel Remaining) This display cannot be reset.
  • Page 97 Automatic Compass Calibration The self-calibrating feature of the compass eliminates the need to calibrate the compass for normal conditions. During a short initial period, the compass may appear erratic and the CAL symbol will appear on the display. After the vehicle has completed at least one complete circle in an area free from large metal objects, calibration will be complete when the CAL symbol is extinguished.
  • Page 98 98 UNDERSTANDING YOUR INSTRUMENT PANEL Setting the Compass Variance Refer to the variance map for the correct compass vari- ance zone. To check the variance zone, the ignition must be on and the compass / temperature displayed. Hold down both the US / M and STEP buttons simultaneously until the VAR symbol is lit and then immediately release both buttons.

  • Page 99: Cigar Lighter/Ashtray

    Outside Temperature If the outside temperature is more than 131°F (55°C), the display will show 131°F. When the outside temperature is less than 40°F ( 40°C), the display will show 40°F/C. CIGAR LIGHTER/ASHTRAY For a nominal charge your dealer can provide a “smok- er’s”...

  • Page 100: Two Types Of Signals

    100 UNDERSTANDING YOUR INSTRUMENT PANEL Two Types of Signals There are two basic types of radio signals... AM or Amplitude Modulation, in which the transmitted sound causes the amplitude, or height, of the radio waves to vary... and FM or Frequency Modulation, in which the frequency of the wave is varied to carry the sound.

  • Page 101: Power Switch, Volume Control

    Power Switch, Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. The volume will be displayed and continuously updated while the button is pressed. Seek Button (Radio Mode) Press and release the Seek button to search for the next station in either the AM or FM mode.
  • Page 102 102 UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the PTY button to select the following format types: Program Type Adult Hits Adlt Hit Classical Classicl Classic Rock Cls Rock College College Country Country Information Inform Jazz Jazz Foreign Language Language News News Nostalgia Nostalga Oldies...

  • Page 103: Balance

    Pressing PTY, then SCAN will scan the FM Band and stop at all RDS stations. Each RDS station will be played for a 5 second scan once around the FM Band and stop at the last station. The PTY icon will then turn off. Balance The Balance control adjusts the left-to-right speaker bal- ance.

  • Page 104: To Change From Clock To Radio Mode

    104 UNDERSTANDING YOUR INSTRUMENT PANEL 5 seconds after pressing the SET button, the station will continue to play but will not be locked into push-button memory. You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window.

  • Page 105: Tape Eject

    Tape Eject Press the EJT Tape button and the cassette will disengage and eject from the radio. Scan Button Press this button to play 10 seconds of each selection. Press the scan button a second time to cancel the feature. Changing Tape Direction If you wish to change the direction of tape travel (side being played), press the PTY button.

  • Page 106: Inserting The Compact Disc

    106 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! This CD player will accept 4 only. The use of other sized discs may damage the CD player mechanism. Inserting The Compact Disc The CD player contained within the radio is not a multi-disc changer, and will only accept one CD. Gently insert one CD into the CD player with the CD label facing up.

  • Page 107: Ff/Tune/Rw

    FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW ( Reverse) button works in a similar manner. Program Button 4 (Random Play) Press this button while the CD is playing to activate Random Play.

  • Page 108: Cd Changer Control Capability - If Equipped

    108 UNDERSTANDING YOUR INSTRUMENT PANEL CD Changer Control Capability — If Equipped This radio is compatible with a remote mounted CD changer available through Mopar Accessories. The fol- lowing instructions are for the radio controls that operate this CD changer. Mode Button To activate the CD changer, press the MODE button until CD information appears on the display.

  • Page 109: Sales Code Rbb-Am/Fm Stereo Radio With Cassette Tape Player And Cd Changer Capability

    An ERR symbol will appear on the display if the laser is unable to read the Disc data for the following reasons: • Excessive vibration • Disc inserted upside down • Damaged disc • Water condensation on optics SALES CODE RBB—AM/FM STEREO RADIO WITH CASSETTE TAPE PLAYER AND CD CHANGER CAPABILITY NOTE: The radio sales code is located on the lower left...
  • Page 110 110 UNDERSTANDING YOUR INSTRUMENT PANEL Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the right increases the volume and to the left decreases it. When the audio system is turned on, the sound will be set at the same volume level as last played.

  • Page 111: Mode Button

    Audio The audio button controls the BASS, TREBLE, BAL- ANCE, and FADE. Press the AUDIO button and BASS will be displayed. Press the SEEK + or SEEK – to increase or decrease the Bass tones. Press the AUDIO button a second time and TREB will be displayed.

  • Page 112: Cassette Player Features

    112 UNDERSTANDING YOUR INSTRUMENT PANEL Cassette Player Features With ignition OFF and the sound system OFF, you can eject the tape cassette by pushing the EJECT button. You can turn the tape player ON by inserting a cassette or activating the MODE button (with a cassette in the radio), but only when the ignition and radio are on.

  • Page 113: Cd Changer Control Capability - If Equipped

    When Dolby is ON, the NR symbol appears on the display. Each time a tape is inserted the Dolby will turn * “Dolby” noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. Dolby and the double-D symbol are trademarks of Dolby Labo- ratories Licensing Corporation.

  • Page 114: Sales Code Rbk-Am/ Fm Stereo Radio With Cd Player And Cd Changer Controls

    114 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual. CD Diagnostic Indicators When driving over a very rough road, the CD player may skip momentarily. Skipping will not damage the disc or the player, and play will resume automatically.

  • Page 115: Radio Operation

    Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio.

  • Page 116: Cd Player Operation

    116 UNDERSTANDING YOUR INSTRUMENT PANEL Press the AUDIO button and BASS will be displayed. Press the SEEK + or SEEK – to increase or decrease the Bass tones. Press the AUDIO button a second time and TREB will be displayed. Press the SEEK + or SEEK – to increase or decrease the Treble tones.
  • Page 117 Inserting The Compact Disc CAUTION! This CD player will accept 4 ⁄ inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. You may either insert or eject a disc with the radio OFF. If you insert a disc with the ignition ON and the radio OFF, the display will show the time of day.

  • Page 118: Cd Changer Control Capability - If Equipped

    118 UNDERSTANDING YOUR INSTRUMENT PANEL Press the SEEK button to move to the next randomly selected track. Press the RND (button 4) button a second time to stop Random Play. Mode Press the MODE button repeatedly to select between the CD player, the optional remote CD changer and the Satellite Radio (if equipped).
  • Page 119 Random Play (RND) Press the Random button to play the tracks on the selected disc in random order for an interesting change of pace. Random can be cancelled by pressing the button a second time or by ejecting the CD from the changer. Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s...

  • Page 120: Sales Code Rb1-Am/Fm Stereo Radio With Dvd/Gps Navigation System

    120 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RB1—AM/FM STEREO RADIO WITH DVD/GPS NAVIGATION SYSTEM RB1 Radio The navigation system provides maps, turn identifica- tion, selection menus and instructions for selecting a variety of destinations and routes. Refer to your “Navi- gation User’s Manual”...

  • Page 121: Loading The Cd Changer

    Loading the CD Changer When inserting the first CD into the changer if the radio is on, wait until the single slot is illuminated on both sides and simply insert the first disc. To insert additional CDs into the changer, the instructions follow: 1.

  • Page 122: Program Button 1

    122 UNDERSTANDING YOUR INSTRUMENT PANEL Program Button 1 Press this button to play the next available disc. Program Button 4 (Random Play) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the current compact disc in random order to provide an interesting change of pace.

  • Page 123: Cd Changer Operation With The Changer Off

    To eject additional CDs from the changer, first select the numbered button where the CD is located and then press the EJT button. CD Changer Operation with the Changer Off The CD changer is able to load and eject discs with the ignition power off.

  • Page 124: Selecting Satellite Mode In Rbb, Rah And Rbk Radios

    124 UNDERSTANDING YOUR INSTRUMENT PANEL ESN/SID Access With RBP, RBU, RAZ, RB1 and RBQ Radios With the ignition switch in the ACCESSORY position and the radio OFF, press the CD Eject and TIME buttons simultaneously for 3 seconds. All twelve ESN/SID num- bers will be displayed.

  • Page 125: Storing And Selecting Pre-Set Channels

    888-539-7474 to discuss options for channel blocking or unblocking. Please have your ESN/SID information available. Storing and Selecting Pre-Set Channels In addition to the 10 AM and 10 FM pre-set stations, you may also commit 10 satellite stations to push button memory.

  • Page 126: Remote Sound System Controls - If Equipped

    126 UNDERSTANDING YOUR INSTRUMENT PANEL • Dense tree coverage may interrupt reception in the form of short audio mutes. • Driving under wide bridges or along tall buildings can cause intermittent reception. • Placing objects over or too close to the antenna can cause signal blockage.

  • Page 127: Radio Operation

    The left hand control is a rocker type switch with a push-button in the center. The function of the left hand control is different depending on which mode you are in. The following describes the left hand control operation in each mode.

  • Page 128: Cassette Tape And Player Maintenance

    128 UNDERSTANDING YOUR INSTRUMENT PANEL CASSETTE TAPE AND PLAYER MAINTENANCE To keep the cassette tapes and player in good condition, take the following precautions: 1. Do not use cassette tapes longer than C-90; otherwise, sound quality and tape durability will be greatly dimin- ished.

  • Page 129: Radio Operation And Cellular Phones

    6. Do not expose the disc to direct sunlight. 7. Do not store the disc where temperatures may become too high. NOTE: If you experience difficulty in playing a particu- lar disc, it may be damaged, oversized, or have theft protection encoding.
  • Page 130 130 UNDERSTANDING YOUR INSTRUMENT PANEL near the windshield glass. The In-Car Temperature Sen- sor is mounted behind the ATC control panel. These sensors transmit data on sun strength and vehicle interior temperatures to enhance system performance. CAUTION! Do not cover either sensor with any foreign material as improper operation of the system will result.
  • Page 131 61,...to 89,90, Hi, for automatic temperature control. You can select a very hot or cold comfort setting by holding the comfort control until it reaches its highest or lowest levels. The system adjusts to bring the interior temperature to the desired comfort level. All comfort settings are auto- matic;...
  • Page 132 132 UNDERSTANDING YOUR INSTRUMENT PANEL Air Direction Buttons (Mode) These buttons allow you to select from five air distribu- tion patterns. These buttons should be used only when you can not achieve comfort or visibility in Auto opera- tion. A symbol in the display window will show which mode is operating.
  • Page 133 NOTE: The air conditioning compressor is on in this mode. This dehumidifies the air to help dry the wind- shield. To improve fuel economy, leave in the defrost mode only when necessary. Rear Window Defroster Press the button once to turn on the Rear Window Defroster and a second time to turn it off.
  • Page 134 134 UNDERSTANDING YOUR INSTRUMENT PANEL Side Window Demisters Side window demisters are located on the instrument panel. These non adjustable outlets direct air toward the side windows in any mode except Panel or Panel Recir- culation. The air is directed toward the area of the side windows through which you view the outside rearview mirrors.
  • Page 135 UNDERSTANDING YOUR INSTRUMENT PANEL 135 Operating Tips (ATC only)

  • Page 136: Manual Air Conditioning/Heater Control

    136 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If the system is in the AUTO mode and the fan control is already rotated fully clockwise or fully coun- terclockwise, the control may have to be rotated to the middle and then to the desired fan setting for manual adjustment of fan speed.
  • Page 137 Slight changes in engine speed or power may be noticed when the air conditioning compressor is on. This is a normal occurrence as the compressor will cycle on and off to maintain comfort and increase fuel economy. NOTE: If your air conditioning performance seems lower than expected, check the front of the air condition- ing condenser for an accumulation of dirt or insects.
  • Page 138 138 UNDERSTANDING YOUR INSTRUMENT PANEL • Panel — Air Conditioning Outside air flows through the air condition- ing system and then through the outlets located in the instrument panel. • Bi-Level — Air Conditioning Outside air flows through the air condition- ing system and then through the outlets located in both the instrument panel and floor outlets.
  • Page 139 Rear Seat Outlets These outlets are located under the front seats and direct warm air to the rear seat passengers. Air is directed through these outlets when you select either the Floor, Bi-Level, or Mix modes. Rear Window Defroster The Rear Window Defroster button is located to the right of the Mode Control.
  • Page 140 140 UNDERSTANDING YOUR INSTRUMENT PANEL Summer Operation Air conditioned vehicles must be protected with a high- quality antifreeze coolant to provide proper corrosion protection and to raise the boiling point of the coolant for protection against overheating. A 50 % concentration is recommended.
  • Page 141 UNDERSTANDING YOUR INSTRUMENT PANEL 141 Operating Tips (Manual A/C Control Only)
  • Page 142 142 UNDERSTANDING YOUR INSTRUMENT PANEL Outside Air Intake Make sure the air intake, directly in front of the wind- shield, is free of ice, slush, snow or other obstructions such as leaves. Leaves collected in the air-intake plenum may reduce air flow and plug the plenum water drains. Air Intake...
  • Page 143 STARTING AND OPERATING CONTENTS Starting Procedures ....146 Automatic Transaxle ....146 Manual Transaxle .
  • Page 144 144 STARTING AND OPERATING Tire Safety Information ....158 Tire Markings ......158 Tire Identification Number (TIN) .
  • Page 145 Fuel Requirements ....182 Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles ... . . 182 Starting .

  • Page 146: 146 Starting And Operating

    146 STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. CAUTION! Long periods of engine idling, especially at high engine speeds can cause excessive exhaust tempera- tures which can damage your vehicle.

  • Page 147: Extreme Cold Weather (Below -20°F Or -29°C)

    Ignition Key Positions WARNING! Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury. STARTING AND OPERATING 147 CAUTION! Do not attempt to push or tow your vehicle to get it started.

  • Page 148: If Engine Fails To Start

    148 STARTING AND OPERATING If Engine Fails to Start If the engine fails to start after you have followed the “NORMAL STARTING” WEATHER” procedures, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there while cranking the engine.

  • Page 149: Automatic Transaxle

    WARNING! Remember to disconnect the cord before driving. Damage to the 110-115 volt AC electrical cord could cause electrocution. Use the heater when temperatures below 0°F (-18°C) are expected to last for several days. AUTOMATIC TRANSAXLE Brake/Transmission Interlock This interlock system prevents you from moving the gear selector out of the Park position unless the brake pedal is pressed.

  • Page 150: Automatic Transaxle Ignition Interlock System

    150 STARTING AND OPERATING CAUTION! Damage to the transaxle may occur if the following precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed.

  • Page 151: Four Speed Automatic Transaxle

    Four Speed Automatic Transaxle The electronically controlled transaxle provides a precise shift schedule. The transaxle electronics are self calibrat- ing; therefore, the first few shifts on a new vehicle may be somewhat abrupt. This is a normal condition, and preci- sion shifts will develop within a few shift cycles.
  • Page 152 152 STARTING AND OPERATING WARNING! Your vehicle could move and injure you and others if it is not completely in P (Park). Check by trying to move the gearshift lever back and forth without depressing the shift button after you have set it in P. Make sure it is in Park before leaving the vehicle.

  • Page 153: Parking Brake

    NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve perfor- mance, fuel economy, and extend transaxle life by reduc- ing excessive shifting and heat build up. Use the “3” range when descending steep grades to prevent brake system distress.
  • Page 154 154 STARTING AND OPERATING To release the parking brake, apply the brake pedal and pull up on the parking brake lever. Push the release button and lower the lever fully. When parking on a hill, it is important to set the parking brake before placing the gear selector in Park, otherwise the load on the transmission locking mechanism may make it difficult to move the selector out of Park.

  • Page 155: Brake System

    BRAKE SYSTEM Your vehicle is equipped with power assisted brakes as standard equipment. In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. The effort required to brake the vehicle will be much greater than that required with the power system operating.
  • Page 156 156 STARTING AND OPERATING WARNING! Pumping of the brake pedal will diminish the effec- tiveness of Anti-lock brakes and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. WARNING! •...

  • Page 157: Power Steering

    POWER STEERING The power assisted steering system of your vehicle provides mechanical steering capability in the event power assist is lost. If for some reason the hydraulic pressure is interrupted, it will still be possible to steer your vehicle. Under these conditions you will observe a substantial increase in steering effort.

  • Page 158: Tire Safety Information

    158 STARTING AND OPERATING A push-button located on the top of the steering column turns the Traction Control System ON or OFF. The system is always in the “ON” mode unless: • The traction control switch has been used to turn the system off;...
  • Page 159 • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter P is absent from this tire size designation. Example: 215/65R15 96H •...
  • Page 160 160 STARTING AND OPERATING Tire Sizing Chart Size Designation: P = Passenger car tire size based on U.S. design standards ...blank... = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm)
  • Page 161 Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved un- der specified operating conditions.

  • Page 162: Tire Identification Number (Tin)

    162 STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire.

  • Page 163: Tire Loading And Tire Pressure

    Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar. Tire Placard Location STARTING AND OPERATING 163 Tire and Loading Information Placard Tire and Loading Information This placard tells you important information about the:...
  • Page 164 164 STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the “Tire and Loading Information”...
  • Page 165 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. NOTE: The following table shows examples on how to calculate total load, cargo/luggage and towing capacities of your vehicle with varying seating configurations and STARTING AND OPERATING 165...
  • Page 166 166 STARTING AND OPERATING...

  • Page 167: Tires-General Information

    WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.

  • Page 168: Tire Inflation Pressures

    168 STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption.
  • Page 169 CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure”.

  • Page 170: Radial-Ply Tires

    170 STARTING AND OPERATING WARNING! High speed driving with your vehicle under maxi- mum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h).

  • Page 171: Limited Use Spare - If Equipped

    Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. Do not install more than one compact spare tire/wheel on the vehicle at any given time. CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with the...

  • Page 172: Tread Wear Indicators

    172 STARTING AND OPERATING WARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck. And don’t let anyone near a spinning wheel, no matter what the speed.

  • Page 173: Life Of Tire

    Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: • Driving style • Tire pressure • Distance driven WARNING! Tires and spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure.

  • Page 174: Alignment And Balance

    174 STARTING AND OPERATING WARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combina- tions of unapproved tires and wheels may change suspension dimensions and performance charac- teristics, resulting in changes to steering, han- dling, and braking of your vehicle.

  • Page 175: Tire Chains

    TIRE CHAINS Due to limited clearance, tire chains are not recom- mended. CAUTION! Damage to the vehicle may result if tire chains are used. SNOW TIRES Some areas of the country require the use of snow tires during winter. Standard tires are of the all season type and satisfy this requirement as indicated by the M+S designation on the tire side wall.

  • Page 176: Autostick - If Equipped

    176 STARTING AND OPERATING Follow the recommended tire rotation frequency for your type of driving found in the “Maintenance Schedules” Section of this manual. More frequent rotation is permis- sible if desired. The reasons for any rapid or unusual wear should be corrected before rotating. The suggested rotation method is the “forward-cross”...

  • Page 177: Autostick General Information

    autostick lever to the AUTOSTICK position. The trans- axle will remain in the current gear until an upshift or downshift is chosen. Gear Selector Move the lever back to the Overdrive position to shift out of the Autostick mode. Autostick General Information •...

  • Page 178: Fuel Requirements

    If you experience these symptoms, try another brand of “regular” gasoline be- fore considering service for the vehicle. Over 40 automobile manufacturers around the world have issued and endorsed consistent gasoline specifica- tions (the World Wide Fuel Charter, WWFC) to define fuel properties necessary to deliver enhanced emissions, engine performance, and durability for your vehicle.

  • Page 179: Mmt In Gasoline

    CAUTION! DO NOT use gasolines containing Methanol. Use of these blends may result in starting and driveability problems and may damage critical fuel system com- ponents. Problems that result from using methanol/gasoline blends are not the responsibility of the manufacturer. While MTBE is an oxygenate made from Methanol, it does not have the negative effects of Methanol.

  • Page 180: Fuel System Cautions

    180 STARTING AND OPERATING Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law. Using leaded gasoline can impair engine performance, or damage the emission control system. •...

  • Page 181: Flexible Fuel- (Fleet Vehicles Only)

    • Guard against carbon monoxide with proper mainte- nance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Keep the trunk closed when driving your vehicle to prevent carbon monoxide and other poisonous ex- haust gases from entering the vehicle.

  • Page 182: Fuel Requirements

    182 STARTING AND OPERATING Fuel Requirements Your vehicle will operate on both unleaded gasoline with an octane rating of 87, or E-85 fuel, or any mixture of these two. For best results, a refueling pattern that alternates be- tween E-85 and unleaded gasoline should be avoided. When you do switch fuels, it is recommended that •...

  • Page 183: Replacement Parts

    Replacement Parts Many components in your Flexible Fuel Vehicle (FFV) are designed to be compatible with ethanol. Always be sure that your vehicle is serviced with correct ethanol com- patible parts. CAUTION! Replacing fuel system components with non-ethanol compatible components can damage your vehicle. Maintenance If you operate the vehicle using E-85 fuel, follow Sched- ule B in the maintenance schedule section of this manual.
  • Page 184 184 STARTING AND OPERATING NOTE: Tighten the gas cap until you hear a “clicking” sound. This is an indication that the gas cap is properly tightened. The Malfunction Indicator Light will come on if the gas cap is not properly secured. Make sure that the gas cap is tightened each time the vehicle is refueled.

  • Page 185: Vehicle Loading

    VEHICLE LOADING Vehicle Loading Capacities Front Seat Occupants ..... . . 2 Rear Seat Occupants ......2 Luggage .
  • Page 186 186 STARTING AND OPERATING Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear GAWR.

  • Page 187: Trailer Hitch Classification

    Trailer Hitch Classification The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Refer to the Trailer Towing Weights (Maximum Trailer Weight Ratings) chart for the Max.

  • Page 188: Trailer Towing Weights (Maximum Trailer Weight Ratings)

    188 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/Transmission Frontal Area 2.4L Automatic/ Manual 2.7L Automatic/ Manual Refer to local laws for maximum trailer towing speeds. Note 1 –...

  • Page 189: Trailer And Tongue Weight

    Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to side which will cause loss of control of vehicle and trailer.

  • Page 190: Towing Requirements

    190 STARTING AND OPERATING Towing Requirements To promote proper break-in of your new vehicle driv- etrain components the following guidelines are recom- mended: CAUTION! • Avoid towing a trailer for the first 500 miles (805 km) of vehicle operation. Doing so may damage your vehicle.
  • Page 191 • Vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the tow vehicle. Put the tow vehicle automatic transmission in P for Park. With a manual transmission, shift the transmission into reverse. Always, block or chock the trailer wheels.
  • Page 192 192 STARTING AND OPERATING Towing Requirements — Trailer Brakes − Do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer. This could cause inadequate braking and possible personal injury. − An electronically actuated trailer brake controller is required when towing a trailer with electronically actuated brakes.
  • Page 193 STARTING AND OPERATING 193 Towing Requirements — Trailer Lights & Wiring Whenever you pull a trailer, regardless of the trailer size, stop lights and turn signals on the trailer are required for motoring safety. The Trailer Tow Package may include a 4 and 7 pin wiring harness.

  • Page 194: Towing Tips

    194 STARTING AND OPERATING 7- Pin Connector Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. If using a manual transmission vehicle for trailer towing, all starts must be in FIRST gear to avoid excessive clutch slippage.
  • Page 195 Towing Tips — Electronic Speed Control (If Equipped) − Don’t use in hilly terrain or with heavy loads. − When using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed. −...
  • Page 197 WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....198 If Your Engine Overheats ....198 Jacking And Tire Changing .

  • Page 198: 198 What To Do In Emergencies

    198 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER Hazard Flasher Switch The flasher switch is on top of the steering column, just behind the steering wheel. Depress the switch and both cluster indicators and all front and rear direc- tional signals will flash.

  • Page 199: Jacking And Tire Changing

    CAUTION! Driving with a hot cooling system could damage your vehicle. If temperature gauge reads “H”, pull over and stop the vehicle. Idle the vehicle in Park with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H”, turn the engine off immediately, and call for service.

  • Page 200: Preparations For Jacking

    200 WHAT TO DO IN EMERGENCIES Preparations for Jacking Park the vehicle on a firm level surface, avoid ice or slippery areas, and set the parking brake. Place the gear selector in PARK. • Turn on the Hazard Warning Flasher, park vehicle on firm, level surface.
  • Page 201 1. Block wheel diagonally op- posite flat tire. 2. Remove the spare tire, scissors jack and lug wrench from stowage. 3. Before raising the vehicle, use lug wrench to carefully pry off wheel cover (if equipped with steel wheels) or center cap (if equipped with aluminum wheels).
  • Page 202 202 WHAT TO DO IN EMERGENCIES Jack Engagement Locations...
  • Page 203 WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove lug nuts and tire. 7. Mount spare tire. 8.

  • Page 204: Jump-Starting Procedures If Battery Is Low

    204 WHAT TO DO IN EMERGENCIES JUMP-STARTING PROCEDURES IF BATTERY IS WARNING! • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transaxle cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
  • Page 205 WARNING! Do not permit vehicles to touch each other as this could establish a ground connection and person injury could result. Jump Starting WHAT TO DO IN EMERGENCIES 205 5. Connect the other cable, first to the negative terminal of the booster battery and then to the jump start attach- ment of the vehicle with the discharged battery.
  • Page 206 206 WHAT TO DO IN EMERGENCIES 7. When removing the jumper cables, reverse the above sequence exactly. Be careful of the moving belts and fan. WARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent;...

  • Page 207: Driving On Slippery Surfaces

    DRIVING ON SLIPPERY SURFACES Acceleration Rapid acceleration on snow covered, wet, or other slip- pery surfaces may cause the front wheels to pull errati- cally to the right or left. This phenomenon occurs when there is a difference in the surface traction under the front (driving) wheels, particularly with high output engines.

  • Page 208: Freeing A Stuck Vehicle

    208 WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE If your vehicle is equipped with Traction Control, turn the system off before attempting to “rock” the vehicle. If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels.

  • Page 209: Towing This Vehicle Behind Another Vehicle

    TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE (Flat towing with all four wheels on the ground) Automatic Transaxle Your vehicle may be towed under the following condi- tions: The gear selector must be in NEUTRAL, the distance to be towed must not exceed 15 miles (25 km), and the towing speed must not exceed 25 mph (40 km/h).
  • Page 211 MAINTAINING YOUR VEHICLE CONTENTS 2.4L Engine ......213 2.7L Engine ......214 Onboard Diagnostic System —...
  • Page 212 212 MAINTAINING YOUR VEHICLE Appearance Care And Protection From Corrosion ......241 Convertible Top Care ....246 Washing .

  • Page 213: 2.4L Engine

    MAINTAINING YOUR VEHICLE 213 2.4L ENGINE 2.4L Engine Compartment...

  • Page 214: Maintaining Your Vehicle

    214 MAINTAINING YOUR VEHICLE 2.7L ENGINE 2.7L Engine Compartment...

  • Page 215: Onboard Diagnostic System - Obd Ii

    ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emis- sions well within current government regulations.

  • Page 216: 216 Maintaining Your Vehicle

    216 MAINTAINING YOUR VEHICLE EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running,...

  • Page 217: Replacement Parts

    If your OBD system is not ready, you should see your authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD system to update.

  • Page 218: Maintenance Procedures

    218 MAINTAINING YOUR VEHICLE WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.

  • Page 219: Maintenance Schedules

    Engine Oil Dipstick CAUTION! Overfilling or underfilling will cause aeration or loss of oil pressure. This could damage your engine. Change Engine Oil Road conditions and your kind of driving affects the interval at which your oil should be changed. Check the following list to decide if any apply to you.
  • Page 220 220 MAINTAINING YOUR VEHICLE If none of these apply to you, then change your engine oil at every interval shown on schedule A of the Mainte- nance Schedules section of this manual. NOTE: Under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or 6 months whichever comes first.
  • Page 221 Engine Oil Viscosity (SAE Grade) Engine Oil Fill Cap SAE 5W-20 and SAE 5W-30 engine oils are recom- mended for all operating temperatures. These engine oils are designed to improve low temperature starting and vehicle fuel economy. Refer to the engine oil filler cap for the preferred engine oil viscosity grade for each vehicle.
  • Page 222 222 MAINTAINING YOUR VEHICLE Engine Oil Filter Selection All manufacturer’s engines have a full-flow type dispos- able oil filter. Use a filter of this type for replacement. The quality of replacement filters varies considerably. Only high quality filters should be used to assure most efficient service.
  • Page 223 WARNING! The air cleaner can provide a measure of protection in the case of engine backfire. Do not remove the air cleaner unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air cleaner removed.

  • Page 224: Crankcase Emission Control System

    224 MAINTAINING YOUR VEHICLE WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your ex- haust system. Do not park or operate your vehicle in areas where your exhaust system can contact any- thing that can burn.

  • Page 225: Maintenance-Free Battery

    Maintenance-Free Battery The top of the MAINTENANCE-FREE battery is perma- nently sealed. You will never have to add water, nor is periodic maintenance required. NOTE: The battery is stored in a compartment behind the left front fender and is accessible without removing the tire and wheel.

  • Page 226: Air Conditioner

    226 MAINTAINING YOUR VEHICLE CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and identified on the battery case.

  • Page 227: Power Steering - Fluid Check

    Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocar- bon (HFC) that is endorsed by the Environmental Pro- tection Agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equipment.

  • Page 228: Suspension Ball Joints

    228 MAINTAINING YOUR VEHICLE Fluid level should be maintained at the proper level indicated on the side of the reservoir. If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to Fluids, Lubricants, and Genuine Parts for correct fluid type.

  • Page 229: Windshield Wiper Blades

    If you use a lubricant that cannot be dispensed directly into the lock cylinder, apply a small amount of the lubricant to the key. Insert the key into the lock cylinder, then proceed as described above, to distribute the lubri- cant within the lock cylinder.

  • Page 230: Windshield Washers

    230 MAINTAINING YOUR VEHICLE Windshield Wiper Blade Replacement • Lift the wiper arm away from the glass. • Push the release tab and slide the wiper blade assem- bly away from the wiper arm. Gently place the wiper arm on the windshield. •...

  • Page 231: Exhaust System

    Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle is damaged;...

  • Page 232: Cooling System

    232 MAINTAINING YOUR VEHICLE Cooling System WARNING! • When working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the OFF position. The fan is controlled by both the temperature of the engine cooling system and the pressure in the air conditioning system and can start at any time the ignition switch is in the ON position.
  • Page 233 Selection Of Coolant Use only the manufacturer’s recommended coolant, refer to Fluids, Lubricants and Genuine Parts for correct coolant type. CAUTION! Mixing of coolants other than specified HOAT en- gine coolants, may result in engine damage and may decrease corrosion protection. If a non-HOAT cool- ant is introduced into the cooling system in an emergency, it should be replaced with the specified coolant as soon as possible.
  • Page 234 234 MAINTAINING YOUR VEHICLE Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area where the vehicle is operated. NOTE: Mixing coolant types will decrease the life of the engine coolant and will require more frequent coolant changes.
  • Page 235 ground. If ingested by a child, contact a physician immediately. Clean up any ground spills immediately. Coolant Level The coolant bottle provides a quick visual method for determining that the coolant level is adequate. With the engine off and cold, the level of the coolant in the bottle should be between the ranges indicated on the bottle.

  • Page 236: Hoses And Vacuum/Vapor Harnesses

    236 MAINTAINING YOUR VEHICLE • Maintain coolant concentration at 50% HOAT engine coolant (minimum) and distilled water for proper corrosion protection of your engine which contains aluminum components. • Make sure that the radiator and coolant recovery bottle overflow hoses are not kinked or obstructed. •...
  • Page 237 WARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You may not have your full braking capacity in an emergency.
  • Page 238 238 MAINTAINING YOUR VEHICLE Master Cylinder The fluid level in the master cylinder should be checked when performing under hood services, or immediately if the brake system warning lamp shows system failure. Brake Fluid Reservoir Be sure to clean the top of the master cylinder area before removing the cap.

  • Page 239: Fuel System Hoses

    Do not allow petroleum base fluid to contaminate the brake fluid as seal damage will result! Fuel System Hoses Electronic Fuel Injection high pressure fuel systems are designed with hoses and clamps which have unique material characteristics to provide adequate sealing and resist attack by deteriorated gasoline.
  • Page 240 240 MAINTAINING YOUR VEHICLE Procedure For Checking Fluid Level The fluid level in the automatic transaxle should be checked whenever the vehicle is serviced. Operation with an improper fluid level will greatly reduce the life of the transaxle and of the fluid. To properly check the automatic transaxle fluid level, the following procedure must be used: •...

  • Page 241: Appearance Care And Protection From Corrosion

    • Police, taxi, limousine, commercial type operation, or trailer towing where the vehicle is driven regularly for more than 45 minutes of continuous operation. NOTE: Refer to Section 8 of this manual for mainte- nance schedules. If the transaxle is disassembled for any reason, the fluid and filter should be changed.
  • Page 242 242 MAINTAINING YOUR VEHICLE What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • Road salt, dirt and moisture accumulation. • Stone and gravel impact. •...
  • Page 243 • Use Mopar touch up paint or equivalent on scratches or chips as soon as possible. Your dealer has touch up paint to match the color of your vehicle. • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating have your vehicle repaired as soon as possible.
  • Page 244 244 MAINTAINING YOUR VEHICLE You should not increase the gloss level, especially on top of the instrument panel top surface. Higher gloss levels will increase the reflectivity in the windshield that could decrease visibility under bright light driving conditions. WARNING! Do not use volatile solvents for cleaning purposes.
  • Page 245 Glass Surfaces All glass surfaces should be cleaned on a regular basis with any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning inside rear windows equipped with electric defrosters. Do not use scrapers or other sharp instru- ments which may scratch the elements.

  • Page 246: Convertible Top Care

    246 MAINTAINING YOUR VEHICLE CONVERTIBLE TOP CARE Immediate removal of any contaminant is recommended. Regular washing of the top will enhance its life and appearance, and make successive cleanings easier. Do not subject the top to excessive heat. Frequently vacuum the top and storage compartment.

  • Page 247: Cloth Top Additional Cleaning Procedure

    Vacuuming the top with a wet/dry shop vacuum will decrease the top’s drying time, ensure removal of all dirt, and delete streaks in the material. Multiple cleanings may be necessary to remove stubborn stains. If stains persist, contact your local dealership for further sugges- tions.

  • Page 248: Fuses

    248 MAINTAINING YOUR VEHICLE FUSES Underhood Fuses (Power Distribution Center) Power Distribution Center A Power Distribution Center is located in the engine compartment, near the air cleaner. This information ap- plies to vehicles built without the fuse and relay num- bering embossed on the Power Distribution Center Top Cover.
  • Page 249 Cavity Fuse Circuit 30 Amp Blower Motor Green 10 Amp Red Right High Beam Head- light, High Beam Indica- 10 Amp Red Left High Beam Head- light 15 Amp Power Door Lock Switch Blue Illumination, Power Top Switch, Transmission Range Switch, Daytime Running Light Module (Canada), Power Win- dows, Anti-lock Brake...

  • Page 250: Vehicle Storage

    250 MAINTAINING YOUR VEHICLE Cavity Fuse Circuit 10 Amp Red Instrument Cluster, Transmission Control, Park/Neutral Switch, Body Control Module 10 Amp Red Left Low beam Headlight 20 Amp Yel- Right Low Beam Head- light, Fog Light Switch 10 Amp Red Radio 10 Amp Red Turn Signal and Hazard Flashers, Wiper Switch, Seat Belt Control Module,...

  • Page 251: Replacement Light Bulbs

    REPLACEMENT LIGHT BULBS LIGHT BULBS — Interior Instrument Cluster ..... PC 194 ABS Indicator ......PC 161 Fog Indicators .
  • Page 252 252 MAINTAINING YOUR VEHICLE 3. Gently pry the headlight assembly away from the fender as shown in the picture. This will free the ball stud from its retainer in the fender. Pull the headlight assem- bly away from the vehicle. 4.

  • Page 253: Park, Turn Signal, Sidemarker Bulb Replacement

    5. Pull the bulb out of the socket and replace the bulb. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. MAINTAINING YOUR VEHICLE 253 6. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol.
  • Page 254 254 MAINTAINING YOUR VEHICLE 2. Gently pry the headlight assembly away from the fender as shown in the picture. This will free the ball stud from its retainer in the fender. Pull the headlight assem- bly away from the vehicle. 3.

  • Page 255: Fog Light Bulb Replacement

    Fog Light Bulb Replacement 1. Remove the screw securing the light assembly to the front fascia. 2. Pull the bulb and socket assembly away from the vehicle to expose the bulb and socket assembly. 3. Disconnect the wiring connector from the bulb and socket assembly.

  • Page 256: Rear Light Bulb Replacement

    256 MAINTAINING YOUR VEHICLE Rear Light Bulb Replacement 1. Open the trunk and pull the trunk liner away to expose the wiring connector and light housing plastic retainers. 2. Disconnect the wiring connector as shown and re- move the plastic retainers. Remove the light housing from the vehicle.

  • Page 257: License Plate Bulb Replacement

    License Plate Bulb Replacement 1. Locate both small slots on the outboard side of the license lamp. Using a small screwdriver, remove the entire housing. 2. Turn the bulb socket counterclockwise to remove it from the housing. Pull the bulb out of the socket. Replace the bulb and snap it back into place on the housing of the chrome appliqué.

  • Page 258: Fluids, Lubricants And Genuine Parts

    258 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Spark Plugs Oil Filter (2.4L Engine) Oil Filter (2.7L Engine) Fuel Selection Fluid, Lubricant, or Genuine Part Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Or- ganic Additive Technology) or equivalent.

  • Page 259: Chassis

    Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transaxle Mopar ATF+4 Automatic Transmission Fluid. Brake Master Cylinder Mopar DOT 3, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake flu- ids.
  • Page 261 MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..262 Maintenance Schedules ....262 Schedule “B” ......265 Schedule “A”...

  • Page 262: Emission Control System Maintenance

    262 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
  • Page 263 NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5,000 km) or 3 months, whichever comes first and follow schedule B of the “Maintenance Schedules” section of this manual. NOTE: If ANY of these apply to you then flush and replace the engine coolant every 100,000 miles (160,000 km) or 60 months, whichever comes first, and follow schedule B of the Maintenance Schedules section of this...
  • Page 264 264 MAINTENANCE SCHEDULES • Check all lights and all other electrical items for correct operation. • Check rubber seals on each side of the radiator for proper fit. At Each Oil Change • Change the engine oil filter. • Inspect the exhaust system. •...

  • Page 265: Schedule "B" 265

    SCHEDULE “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (96 000 km) if the vehicle is usually operated under one or more of the conditions marked with an •...
  • Page 266 266 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if necessary.* Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Rotate the tires.
  • Page 267 Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if re- quired.* Replace the air cleaner filter. Inspect and check tension for power steering belt (2.4 Liter Engine). Adjust or replace if re- quired.
  • Page 268 268 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if necessary.* Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Rotate the tires.
  • Page 269 Miles (Kilometers) Change engine oil and engine oil filter, if not re- placed at 3 months. Inspect the air cleaner filter and replace if neces- sary.* Replace the air cleaner filter. Inspect and check tension for power steering belt (2.4 Liter Engine). Adjust or replace if required. Inspect the front and rear brake pads, linings, ro- tors, rear drums and shoes.
  • Page 270 270 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if necessary.* Replace the air cleaner filter. Inspect and check tension for power steering belt (2.4 Liter Engine). Adjust or replace if re- quired.
  • Page 271 Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if necessary.* Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Replace the spark plugs on the 2.7 liter en- gine.
  • Page 272 272 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if necessary.* Replace the air cleaner filter. Replace the spark plugs on the 2.4 liter engine. Replace the ignition cables on the 2.4 liter engine.

  • Page 273: Schedule "A" 273

    SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if necessary.* Replace the air cleaner filter. Replace the spark plugs on 2.4 liter engine. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes.
  • Page 274 274 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect and check tension for power steering belt (2.4 Liter Engine). Adjust or replace if re- quired.
  • Page 275 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Replace the spark plugs on 2.4 liter engine. Replace the spark plugs on 2.7 liter engine.
  • Page 276 276 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Replace the spark plugs on 2.4 liter engine.
  • Page 277 WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.

  • Page 279: If You Need Consumer Assistance

    IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ......280 Prepare For The Appointment .

  • Page 280: Suggestions For Obtaining Service For Your Vehicle

    We want you to be happy with our products and services. Warranty service must be done by an authorized Chrysler, Dodge, or Jeep dealer. We strongly recommend that you take your vehicle to your selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service.
  • Page 281 • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance. • If your dealership is unable to resolve the concern, you may contact the Manufacturer’s Customer Center. Any communication to the Manufacturer’s Customer Center should include the following information: •...

  • Page 282: Warranty Information (U.s. Vehicles Only)

    282 IF YOU NEED CONSUMER ASSISTANCE Service Contract You may have purchased a service contract for your vehicle to help protect you from the high cost of unex- pected repairs after your manufacturer’s new vehicle limited warranty expires. The manufacturer stands be- hind only the manufacturer’s Service Contracts.

  • Page 283: Reporting Safety Defects

    REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administra- tion (NHTSA) in addition to notifying the manufacturer.

  • Page 284: Department Of Transportation Uniform Tire Quality Grades

    • Owner’s Manuals. These manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific Chrysler group vehicles. Included are starting, operating, emergency and maintenance pro- cedures as well as specifications, capabilities and safety tips.

  • Page 285: Treadwear

    Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled con- ditions on a specified government test course. For ex- ample, a tire graded 150 would wear one and a half (1 1/2) times as well on the government course as a tire graded 100.
  • Page 286 286 IF YOU NEED CONSUMER ASSISTANCE WARNING! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive load- ing, either separately or in combination, can cause heat buildup and possible tire failure.
  • Page 287 INDEX...
  • Page 288 288 INDEX About Your Brakes ..... . 155 ABS (Anti-Lock Brake System) ... . . 155 Adding Engine Coolant (Antifreeze) .
  • Page 289 Autostick ......176 Auxiliary Power Outlet ....79 Ball Joints .
  • Page 290 290 INDEX Changing A Flat Tire ....199 Charging System Light ....90 Chart, Tire Sizing .
  • Page 291 Crankcase Emission Control System ..224 Cruise Control (Speed Control) ... . . 72 Cruise Light ......89 Customer Assistance .
  • Page 292 292 INDEX Cooling ......232 Exhaust Gas Caution ....180 Fails to Start .
  • Page 293 Fluids, Lubricants and Genuine Parts ..258 Fog Light Service ..... . . 255 Fog Lights .
  • Page 294 294 INDEX Cleaning ......244 High Beam ......69,90 High Beam/Low Beam Select Switch .
  • Page 295 Latches Hood ....... 63 Lead Free Gasoline ..... . 178 Leaks, Fluid .
  • Page 296 296 INDEX Door ....... 12 Ignition ......9 Lower Anchors and Tether for CHildren (LATCH) .
  • Page 297 Onboard Diagnostic System ... . 215,216 Opener, Garage Door (HomeLink ) ..75 Operator Manual (Owner’s Manual) ..4 Overdrive .
  • Page 298 298 INDEX Reminder, Seat Belt ..... . 27 Remote Keyless Entry (RKE) ....15 Remote Sound System (Radio) Controls .
  • Page 299 Service Manuals ......283 Setting the Clock ......99 Side Window Demisters (Defrosters) .
  • Page 300 300 INDEX General Information ....167 High Speed ......169 Inflation Pressures .
  • Page 301 Tread Wear Indicators ....172 Trip Computer ......95 Trip Odometer .
  • Page 302 NOTES...

Table of Contents

Save PDF