This guide is designed to make installing and using this product as easy as possible. Information in this document has been carefully checked for accuracy at the time of printing; however, Cambridge Audio’s policy is one of continuous improvement, therefore design and specifications are subject to change without prior notice.
What's included with the AXC25/35? Last updated: 7月 29, 2022 10:27. Revision #5436 Inside the box of your AXC25/35 you will receive: 1. AXC CD player. 2. Remote control. 3. 2 x AAA batteries. 4. UK mains lead (Depending on which country the AXA35 was bought).
Front panel controls Last updated: 7月 29, 2022 10:27. Revision #5437 1. Power button - Switches the unit between Standby mode (indicated by dim power LED) and On (indicated by bright power LED). Standby mode is a low power mode where the power consumption is less than 0.5 Watts. This product has APD (Auto Power Down) enabled as default. After inactivity of 20 minutes, the product will automatically switch to Standby.
Page 7
5. Play/Pause - Plays the CD and pauses play. 6. Stop - Stops the CD playing. 7. Skip/Scan - Enables you to skip between and search within tracks. Press briefly to skip a track. Press and hold to scan through a track.
2. LINE OUTPUT - Use good quality interconnect cables from these sockets to any line level input on your amplifier. For best results and matched performance, we recommend connection to a Cambridge Audio amplifier. 3. AC POWER CABLE - Once you have completed all connections to the amplifier, plug the AC power cable into an appropriate mains socket and turn the...
Remote control Last updated: 7月 29, 2022 10:27. Revision #5439 The AXC25 and AXC35 are supplied with a remote control that operates the unit.The supplied AAA batteries must be fitted before the remote control can be used. 1. POWER BUTTON - Switches the AXC35/AXC25 between On and low power eco-friendly Standby mode.
Getting connected Last updated: 7月 29, 2022 10:27. Revision #5440 Line Output connection The line outputs are for connecting to the line level inputs on an amplifier. The diagram below shows a connection to an amplifier. S/P DIF CO-AXIAL Digital Output connection (AXC35 ONLY) The S/P DIF output is for connecting to the input of a separate digital device, such as a DAC or digital recording machine.
2. Once the disc tray has fully opened, carefully place a disc into the tray with the label side facing upwards. 3. Close the disc tray by pressing the ‘Open/Close’ button again. When the tray has fully closed the AXC25/35 will read the disc and display the content information.
Page 13
Normal Disc Play 1. Switch on your amplifier and set its input selector to the correct position. Adjust the volume control to a minimum. 2. Press the Open/Close button to open the disc tray and load a disc. 3. Press the Open/Close button again to close the tray. The CD player will read the disc. 4.
Page 14
4. Press the Remain button again either before or during playback to return to normal play mode. PROGRAMMING DISC PLAY It is possible to program the AXC35/AXC25 to play back in any order only the tracks you wish to listen to. 1. Ensure that a disc is loaded. The display should show the TOC data.
Check the disc is not loaded upside down. Check that the disc is not too scratched or dirty. Check that the disc type is compatible with the AXC25/35. (Check the ‘Operating Instructions’ section of the manual.) There is no sound Ensure that the amplifier is set correctly.
Does the AXC25/35 have its own volume control? The AXC25/35 does not have a volume control of its own. The analogue and digital output (AXC35 only) are both line level. You will need to control the volume via your connected amplifier or DAC.
Need help?
Do you have a question about the AXC25 and is the answer not in the manual?
Questions and answers