Advertisement
1 IMPORTANT ADVICE AND
RECOMMENDATIONS
This Instruction Manual forms an integral part
of the automatic ice-cube maker (also more
simply called "appliance" in the text) and must
be kept for possible future consultation.
In the event of the appliance being sold or
transferred to another person, this Manual must be
handed over to the new user, in order to enable him
to become familiar with the operation of the
equipment and the corresponding advice and
recommendations.
Before installing and using the automatic
ice-cube maker, read the advice and
recommendations contained in this Instruction
Manual very carefully. They are given in order
to ensure safe installation, use and maintenance
of the appliance.
Any specific information or diagrams regarding
particular models will be attached to this Instruction
Manual.
Do not remove any of the panels or grilles.
Open and close the door carefully without
slamming it.
Do not rest objects on the appliance or in
front of the ventilation grilles.
Always lift the appliance to move it. Do
not push or pull it.
Always remove the plug from the power
socket before proceeding with any
cleaning or maintenance operations.
Any use of the automatic ice-cube maker other
than for the production of ice cubes using cold
drinking water is to be considered as improper
use.
Do not use the ice-cube container to cool or
preserve food or drinks, as these operations
could cause the drainage system to become
clogged, thus leading to the container filling up
and water leaking out.
6
Do not obstruct the ventilation and heat-
dissipation grilles, since poor aeration –
in addition to reducing efficiency and
causing poor operation – may also cause
serious damage to the appliance.
Read the following warnings carefully:
The use of an automatic ice-cube maker, as for any
electrical device, requires compliance with certain
fundamental rules; in particular:
•
Do not touch the appliance with wet or damp
hands or feet.
•
Do not use the appliance when you are barefoot.
•
Do not use extensions in premises such as
bathrooms or shower rooms.
•
Do not tug on the power supply cable to
disconnect it from the mains supply.
•
Do not allow the appliance to be used by
children or byincapable persons.
If the ice-cube maker breaks down and/or
operates in a faulty way, switch it off by means
of the main switch fitted during the installation
phase, turn off the water tap, and do not make
any attempt to repair the appliance yourself.
Contact only professionally qualified and
authorized personnel.
In addition to rendering any form of warranty null
and void, modifying (or attempting to modify) this
appliance is extremely dangerous.
To ensure the appliance operates
efficiently and correctly, it is essential to comply
with the manufacturer's instructions and to
make sure that maintenance is performed by
specially qualified personnel.
In the event of a failure, contact the dealer who sold
you the appliance; he will be able to give you the
address of your nearest Authorized Technical
Service Center. Always insist on having genuine
spare parts mounted.
Should you decide to scrap your automatic
ice-cube maker, first disconnect the power supply
cable from the mains, and then cut the cable off.
In addition, proceed as follows:
•
Break off and remove the door in order to
prevent the possible
danger of a child getting trapped inside.
•
Do not allow the coolant gas and oil contained
in the compressor to disperse into the
environment.
•
Dispose of or recover the various materials
according to the
provisions established by the current laws in
force in your country.
This appliance does not contain coolant that
damages the ozone layer.
The manufacturer shall not be liable for
any damage to the environment, animals,
persons or objects caused by incorrect
installation.
2 TECHNICAL DATA (Fig. 1)
The voltage and frequency are given on the data
plate on the appliance. Refer to this data plate to
check compliance.
Voltage (1), power (2), model (3), Serial No. (4)
manufacturer (5).
The weighted equivalent continuous sound level A
of this automatic ice-cube maker is less than 70 dB
(A). The measurements have been made over an
entire ice-cube production cycle, at a distance of 1
m from the surface of the appliance and at a height
of 1.60 m from the floor.
The wiring diagram is stuck on the front counterpanel
of the automatic ice-cube maker.
In order to gain access thereto, unplug the automatic
ice-cube maker from the voltage supply, unscrew
the screws holding the front panel, and slide it away
after first opening.
3 ADVICE ABOUT TRANSPORTATION
The net weight and the weight including packaging
of the automatic ice-cube maker are given on the
cover of this Instruction Manual. Please refer to the
instructions on the packaging in order to correctly
transport and lift the appliance.
To prevent the oil in the compressor from flowing
back into the coolant circuit, always make sure that
the automatic ice-cube maker is kept upright during
transport, storage, and handling. Follow the
instructions given on the packaging.
4 UNPACKING
The appliance must be installed by authorized
personnel in compliance with the current laws
in force and the manufacturer's instructions.
Once you have removed the packaging according
to the instructions on the box, make sure that THE
AUTOMATIC ICE-CUBE MAKER IS IN A
PERFECTLY GOOD CONDITION. If in doubt, DO
NOT USE IT and immediately CONTACT the dealer
who sold it to you.
All the packaging items (plastic bags, cardboard,
polystyrene foam, nails, etc.) must be removed and
put out of the reach of children, as they are potential
sources of danger.
Rest the wooden pallet on the floor and, using a
hex socket wrench, loosen and remove the bolts (6
Fig. 2) that fix the appliance to the pallet.
Lift the automatic ice-cube maker using equipment
fit to bear its weight. Separate the appliance from
the wooden pallet and fit the supplied feet into the
housings on the base plate provided for the purpose.
(7 Fig. 3).
Use a spirit level to ensure that the appliance is
standing perfectly level. If necessary, adjust the feet.
5 INSTALLATION
5.1 CONNECTION DIAGRAM (see Fig. 4)
8. Plug
9. Socket with switch
10. Water tap
11. Water supply pipe
7
Advertisement
