DeWalt DCL043 Instruction Manual page 8

English
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. If charging problems persist, take the tool, battery
pack and charger to your local service center.
3. You may charge a partially used pack whenever you
desire with no adverse effect on the battery pack.
Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
a cloth or soft non‑metallic brush. Do not use water or
any cleaning solutions.
Wall Mounting
Some D WALT chargers are designed to be wall mountable
e
or to sit upright on a table or work surface. If wall mounting,
locate the charger within reach of an electrical outlet, and
away from a corner or other obstructions which may impede
air flow. Use the back of the charger as a template for the
location of the mounting screws on the wall. Mount the
charger securely using drywall screws (purchased separately)
at least 1" (25.4 mm) long, with a screw head diameter of
0.28–0.35" (7–9 mm), screwed into wood to an optimal
depth leaving approximately 7/32" (5.5 mm) of the screw
exposed. Align the slots on the back of the charger with the
exposed screws and fully engage them in the slots.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
OPERATION

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Proper Hand Position (Fig. A)

WARNING: To reduce the risk of serious personal
injury, ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main
6
handle .
Installing and Removing the Battery Pack
(Fig. E)
nOTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack
battery pack with the rails inside the tool's handle and slide
it into the handle until the battery pack is firmly seated in the
tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
5
button and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of this manual.
6
4
into the tool handle, align the
Switch (Fig. A)

CAUTION: Do not stare into spotlight lens. Serious
eye injury could result.
The spotlight has a low beam and high beam setting. Press
1
the switch once for the high beam. Press the switch again
for the low beam. Press the switch again to turn the spotlight
off.
Low Battery Indicator
nOTE: The light will run up to 2.5 hours when using the high
beam and 3.5 hours when using the low beam on a single
battery charge using a 20V, 1.5Ah battery. Using batteries
with higher capacity will produce more run time.
As the battery nears a fully discharged state, the spotlight
will blink twice and then dim, dropping the brightness of
the spotlight below the normal level. The light will continue
to blink twice every 45 seconds until the battery is fully
discharged at which time the light will turn off. Indication
time will vary based on battery pack capacity and the
light setting.
Pivoting Head (Fig. A)
3
The pivoting head rotates in six positions ranging from
0°–90°.
Carrying and Suspending the Spotlight
(Fig. A)

CAUTION: When the spotlight hangs by the loop hook,
do not shake the spotlight or the object from which it
hangs. Do not hang the spotlight from any electrical
wires or anything that is not secure. Personal injury or
property damage may occur.

CAUTION: Only use the loop hook for hanging the LED
spotlight. The loop hook are not intended to support
additional weight. Do not attach or hang anything
additional to the spotlight or risk of breakage may
occur.

CAUTION: Do not use the loop hook to reach with or
to support your weight in any situation.
Loop Hook (Fig. A)
The light may be carried or hung by the loop hook
not in use, the loop may be locked down.
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
This spot light contains no user-serviceable parts, particularly
the LEDs.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
2
. When