Advertisement
Read the instructions relating to any accessory to be used with this compressor. Ensure the safe working pressure of any air
9
appliance used exceeds compressors output pressure. If using a spray gun, check that the area selected for spraying is provided with
an air change system/ventilation.
Ensure the air supply valve is turned off before disconnecting the air supply hose.
9
To move a transportable compressor use the handle only.
9
DO NOT attempt to move the compressor by any other means.
8
Use the compressor in a well ventilated area.
9
Ensure the compressor is placed on a firm surface.
9
Keep tools and other items away from the compressor when it is in use.
9
Keep area clean and clear of unnecessary items.
9
Ensure the air hose is not tangled, twisted or pinched.
9
Keep children and unauthorised persons away from the working area.
9
DO NOT dis-assemble compressor for any reason. The unit must be checked by qualified personnel only.
8
DO NOT use the compressor outdoors, or in damp, or wet locations.
8
DO NOT operate within the vicinity of flammable liquids, gases or solids.
8
DO NOT touch the compressor cylinder, cylinder head or pipe from head to tank as these may be hot.
8
DO NOT use this product to perform a task for which it has not been designed.
8
DO NOT deface the certification plate attached to the compressor tank.
8
DO NOT cover the compressor or restrict air flow around the unit whilst operating.
8
▲
DANGER! DO NOT direct the output jet of air towards people or animals.
DO NOT operate the compressor without an air filter.
8
DO NOT allow anyone to operate the compressor unless they have received full instructions.
8
WARNING! The air tank is a pressure vessel and the following safety measures apply:
‰
DO NOT tamper with the safety valve.
8
DO NOT modify or alter the tank in any way.
8
DO NOT strap or weld anything to the tank.
8
DO NOT subject the tank to impact, vibration or to heat.
8
DO NOT allow contact with abrasives or corrosives.
8
Drain condensation from tank daily and inspect inside walls for corrosion every three months and have a detailed tank inspection
9
carried out annually. The tank shell must not fall below the certified thickness at any point.
WARNING! If an electrical fuse blows, ensure it is replaced with an identical fuse type and rating.
‰
When not in use, store the compressor carefully in a safe, dry, childproof location.
9
When the compressor is not in use it should be switched off, disconnected from the mains supply and the air drained from the tank.
9
1.3.
INSPECTION OF PRESSURE TANK BOTH INTERNAL AND EXTERNAL
1.3.1.
Under the Pressure systems Safety Regulations 2000 it is the responsibility of the owner of the compressor to initiate
a system of inspection that both defines the frequency of the inspection and appoints a person who has specific responsibility for
carrying out the inspection.
2. INTRODUCTION
Twin capacitors and a centrifugal switch aid trouble-free start-up on a good 13A supply. Pump features heavy-duty full cast cylinders, capped
by alloy heads for improved heat dissipation and long-life. Features an easy-to-use bespoke control panel with two outlets, one regulated and
one direct. Heavy-duty pneumatic wheels with single front castor for easy manoeuvrability. Supplied with hose reel to keep your workspace
tidy. Includes a drain valve for easy release of condensed water build-up in the tank.
3. SPECIFICATION
Model No: ................................................................................. SAC3103B
Air Displacement cfm(L/min): .......................................................12.3(347)
Maximum Free Air Delivery cfm(L/min): .........................................9.5(270)
Maximum Pressure: ..............................................................145psi(10bar)
Minimum Rated Supply: ........................................................................16A
Motor Output: ........................................................................................3hp
Outlet: ......................................................Hi-Flow Quick Release Coupling
Phase: ...................................................................................................1ph
Receiver Capacity: .............................................................................. 100L
Size (W x D x H): .........................................................980 x 500 x 800mm
Speed: .......................................................................................... 1140rpm
Supply: ................................................................................................230V
4. ASSEMBLY
Unpack the product and check contents. Should there be any damaged or missing parts contact your supplier immediately.
Refer to attached parts list.
Save the packing material for future transportation of the compressor. We recommend that you store the packing in a safe location,
at least for the period of the guarantee. Then, if necessary, it will be easier to send the compressor
to the service centre.
4.1.
WHEEL ATTACHMENT
4.1.1.
Assemble the wheels and swivel castor using the nuts, bolts and washers supplied (fig 1).
4.2.
ATTACH THE FILTERS
4.2.1.
Screw the filter unit into the port openings in each head as shown in (fig 3).
4.2.2.
Place a filter cover over each threaded rod protruding from the back half of the filter and secure
each with a wing nut (fig 4)
.
© Jack Sealey Limited
Original Language Version
SAC3103B Issue 4 (3,4,5) 01/04/22
fig.1
Advertisement
