Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DMC 5 Wire Analog Resistive Touchscreen FST Series
Summary of Contents for DMC 5 Wire Analog Resistive Touchscreen FST Series
- Page 1 5 Wire Analog Resistive Touchscreen FST Series Product Specifications...
-
Page 2: Table Of Contents
Table of Contents 1. Product Specifications ... 3 1-1. Product Applicable ... 3 1-2. Structure... 3 1-3. Environmental Specifications ... 3 1-4. Mechanical Characteristics ... 3 1-5. Electrical Characteristics... 3 1-6. Appearance... 4 2. Testing Regulation...5 2-1. Testing Regulation ... 5 2-2. -
Page 3: Product Specifications
1. Product Specifications 1-1. Product Applicable § This specification is applied to the 5 wire analog resistive touchscreen: FST Series. 1-2. Structure § Dimensions, structure, and shape are referred on the drawing attached. 1-3. Environmental Specifications Specification Operating Temperature Operating Humidity Storage Temperature Storage Humidity Chemical Resistance... -
Page 4: Appearance
1-6. Appearance § Scratch, dust (W = width, L = length, D = average diameter = (longest + shortest) /2) Item Width (mm) Linear(Scratch/Dust) 0.1≥W>0.05 Over 0.1mm in 0.05≥W>0.03 diameter refer to the Circular. 0.03≥W Circular (Scratch/Dust) Applied only in the Active Area. Scratches or dusts in the outside of the Active Area are acceptable unless the electrical characteristics are affected. -
Page 5: Testing Regulation
2. Testing Regulation 2-1. Testing Regulation § If the regulation is not specified, the test is performed under the supplier’s regulation. § Tests are performed under the room temperature unless specified. The room temperature is referred as follows: Temperature: 20°C±5°C Humidity: 65%±10%RH 2-2. -
Page 6: Electrical Characteristics
2-4. Electrical Characteristics § Terminal Resistance Test Condition: Top and bottom electrodes are measured at the terminal. Judgement: Must satisfy the specification. § Insulation Resistance Test Neighboring Terminals: Measured by applying the reference voltage to the terminals Active Area Electrodes: Measured by applying the reference voltage to the top and bottom electrodes. Judgement: Must satisfy the specification. -
Page 7: Reliability Condition
3. Reliability Condition 3-1. Temperature Condition § Temperature Condition Test Following test are performed in the condition with no dew condensation: Cold Test: Tested after leaving the parts in -40°C±3°C for 240 hours and in the room temperature for 2 hours. Heat Test: Tested after leaving the parts in 80°C±3°C for 240 hours and in the room temperature for 2 hours. -
Page 8: Handling Notes
5. Handling Notes 5-1. Precautions § This product is intended for use in standard applications (computers, office automation, and other office equipment, industrial, communications, and measurement equipment, personal and household devices, etc.) Please avoid using this product for special applications where failure or abnormal operation may directly affect human lives, or cause physical injury or property damage, or where extremely high levels of reliability are required (such as aerospace systems, vehicle operating control, atomic energy controls, medical devices for life support, etc.). -
Page 9: Mounting Notes
5-5. Mounting Notes § Gap between the Bezel and Touchscreen A gap of approximately 0.5mm is needed between the bezel and the top electrode. It may cause unexpected input if the gap is too narrow. § Cushion If a cushion is used between the bezel and the top electrode, the cushion must be free enough to absorb the expansion and contraction difference between the bezel and the top electrode. -
Page 10: Warranty
6. Warranty 6-1. Warranty Period § The warranty period is limited to 3 years from the date of shipping. The warranty for the initial defection such as appearance defection is limited to 1 month. § Any defected parts under proper use will be examined by the supplier and replaced by the new parts if the defection is considered to be caused by the supplier. -
Page 11: Revision History
7. Revision history Rev1.0 (May 11, 2005) Initial release Rev1.1 (July 13, 2005) 4-1.Recommended Connector is changed RE-H052SD-1130 to RE-H052SD-1110. 6-1.Warranty Period is changed 5 years to 3 years. Rev2.0 (October 13, 2006) The specification item name was changed. 1-3.”Storing Temperature” to “Storage Temperature” 1-3.”Storing Humidity”... - Page 12 FST Series Product Specifications 6-6. RoHS Compliance: Description about RoHS compliance has been added. DER-S0081A Rev. 4.0 ©2005 - 2011 DMC Co., Ltd.
- Page 13 FST Series Product Specifications FST Series Product Specifications Rev. 4.0, August 25, 2011 © 2005 - 2010 DMC Co., Ltd. This document can be freely distributed, but any alternation to this document is prohibited. http://www.dmccoltd.com/english/ floor, Kanda Sento Building, 1-2-4 Yushima, Bunkyo-Ku, Tokyo 113-0034, Japan Phone: +81-3-5209-7131 (Japanese), 7135 (English) Fax: +81-3-5209-7130 DER-S0081A Rev.
Need help?
Do you have a question about the 5 Wire Analog Resistive Touchscreen FST Series and is the answer not in the manual?
Questions and answers