Page 1
All manuals and user guides at all-guides.com Oper ator ′ s manual 327HD A65 X-series 327HE3 327HE4 X-series X-series Please r ead the operator’s manual carefully and make sure you understand the instructions before using the machine. E E E E n n n n g g g g l l l l i i i i s s s s h h h h...
All manuals and user guides at all-guides.com KEY T O SYMBOLS Symbols W ARNING! Incorrect or careless Always wear approved protective use of a hedge trimmer can turn it gloves. into a dangerous tool that can cause serious or even fatal injury. It is extremely important that you read and understand the contents of this operator’s manual.
All manuals and user guides at all-guides.com CONTENTS Contents Note the f ollowing before starting: KEY TO SYMBOLS Symbols ..............2 Please read the oper ator’s manual carefully. CONTENTS Contents ............... 3 W ARNING! Long-term exposure to noise can result in permanent hearing Note the following before starting: ......
The business concept is to develop, manufacture and market motor driven products for forestry and gardening as well as for building and construction industry. Husqvarna ′ s aim is also to be in the front edge according to ergonomics, usability, security and environmental protection.
All manuals and user guides at all-guides.com WHA T IS WHA T? 327HE4 327HDA65 What is what? 1 Cutter 16 Air purge 2 Grease nipple and plug for filling lubricant. 17 Air filter cover 3 Bevel gear 18 Clutch cover 4 Blade guard (327HDA65) 19 Hand guard mounting screw (327HDA65, 327HE3) 5 Shaft...
All manuals and user guides at all-guides.com GENERAL SAFETY PRECA UTIONS Impor tant Personal protective equipment IMPORTANT! IMPOR TANT! The machine is only designed for cutting branches and Incorrect or careless use of a hedge trimmer can turn it twigs. into a dangerous tool that can cause serious or even fatal injury.
All manuals and user guides at all-guides.com GENERAL SAFETY PRECA UTIONS CLO THING the throttle control is automatically locked at the idle setting. Wear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches. Always wear heavy, long pants.
Page 8
All manuals and user guides at all-guides.com GENERAL SAFETY PRECA UTIONS position then the carburettor idle setting must be adjusted. Vibration damping system See instructions under the heading Maintenance. Your machine is equipped with a vibration damping system that is designed to minimize vibration and make operation easier.
Page 9
All manuals and user guides at all-guides.com GENERAL SAFETY PRECAUTIONS a spark arrestor mesh. Check whether the muffler on your Blades machine is fitted with this kind of mesh. To ensure good cutting results it is important that the contact pressure between the blades is correct. The contact pressure is adjusted by turning the screws on the underside of the bar clockwise as far as they will go.
All manuals and user guides at all-guides.com ASSEMBLY Fitting the hand guard and loop Fitting the handle handle (327HE3, 327HE4) (327HDA65, 327HE3) Fit the handle using two screws. 1 Assemble the hand guard and loop handle by screwing them together. Take care to align the holes in both parts.
All manuals and user guides at all-guides.com ASSEMBLY Adjusting the harness (327HE4) You should always use the harness with the machine to give maximum control over the machine and reduce the risk of fatigue in your arms and back. 1 Put on the harness. 2 Hook the machine onto the harness support hook.
• In order to prevent unintentional starting of the engine, • For best results and performance use HUSQVARNA the spark plug cap must always be removed during two-stroke engine oil, which is specially formulated for long-term storage, if the machine is not under close our air-cooled two-stroke engines.
All manuals and user guides at all-guides.com FUEL HANDLING Mixing Fuelling • Always mix the petrol and oil in a clean container intended for fuel. • Always start by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture.
All manuals and user guides at all-guides.com STARTING AND STOPPING Check before starting Starting and stopping • Inspect the working area. Remove any objects that WARNING! The complete clutch cover could be thrown out. and shaft must be fitted before the •...
Page 15
All manuals and user guides at all-guides.com STARTING AND STOPPING CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine. CAUTION! Do not put any part of your body in marked area.
All manuals and user guides at all-guides.com WORKING TECHNIQUES General working instructions • Never work from a ladder, stool or any other raised position that is not fully secured. IMPORTANT! This section takes up the basic safety precautions for working with a hedge trimmer. If you encounter a situation where you are uncertain how to proceed you should ask an expert.
Page 17
All manuals and user guides at all-guides.com WORKING TECHNIQUES • Always lay the machine on the ground when you are • Adjust the throttle setting to suit the load. not using it. • When trimming a hedge the engine should always •...
All manuals and user guides at all-guides.com WORKING TECHNIQUES (327HDA65) Transport position • Undo the knob. (327HE4) Once the work has been completed fold the cutting unit back against the shaft to simplify transport and storage of the hedge trimmer. 1 Turn off the engine.
Basic setting • The basic carburettor settings are adjusted during Your Husqvarna product has been designed and testing at the factory. The basic setting is richer than manufactured to specifications that reduce harmful the optimal setting and should be maintained for the emissions.
All manuals and user guides at all-guides.com MAINTENANCE cause fire if directed against dry and combustible Cooling system material. To keep the working temperature as low as possible the machine is equipped with a cooling system. Some mufflers are equipped with a special spark arrestor mesh.
See instructions under the heading Oiling the air filter. Oiling the air filter Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact.
All manuals and user guides at all-guides.com MAINTENANCE Cleaning and lubrication Clean any resin and plant residue from the blades using cleaning agent 531 00 75-13 (UL22) before and after using the machine. Lubricate the blade bars with special grease, part no. 531 00 75-12 (UL 21) before long periods of storage.
All manuals and user guides at all-guides.com MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this Operator’s Manual.
All manuals and user guides at all-guides.com TECHNICAL DATA Technical data 327HDA65 327HE3 327HE4 Engine Cylinder displacement, cm 25,4 25,4 25,4 Cylinder bore, mm Stroke, mm Idle speed, rpm 2700 2700 2700 Recommended max. speed, rpm 11000-12600 11000-12600 11000-12600 Max. engine output, acc. to ISO 8893, kW/ rpm 0,9/8500 0,9/8500 0,9/8500...
Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare under sole responsibility that the hedge trimmers Husqvarna 327HDA65 from 2009’s serial numbers and onwards (the year is clearly stated in plain text on the type plate with subsequent serial number), are in conformity with the standards or or other normative documents following the provisions in the COUNCIL’S DIRECTIVES:...
Page 26
All manuals and user guides at all-guides.com...
Page 27
All manuals and user guides at all-guides.com...
Page 28
All manuals and user guides at all-guides.com 1151377-26 ´®z+SEh¶6Y¨ ´®z+SEh¶6Y¨ 2009-05-11...