Dahua DHI-ITC237-PW1B-IRZ User Manual
  1. Manuals
  2. Brands
  3. Dahua Manuals
  4. Security Camera
  5. DHI-ITC237-PW1B-IRZ
  6. User manual

Dahua DHI-ITC237-PW1B-IRZ User Manual

2.0 mp cmos hd camera
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
2.0 MP CMOS HD Camera User's Manual
Version 1.0.0
i

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DHI-ITC237-PW1B-IRZ and is the answer not in the manual?

Questions and answers

Related Manuals for Dahua DHI-ITC237-PW1B-IRZ

Summary of Contents for Dahua DHI-ITC237-PW1B-IRZ

  • Page 1 2.0 MP CMOS HD Camera User’s Manual Version 1.0.0...
  • Page 2 Welcome Thank you for purchasing our HD intelligent traffic camera! This user’s manual is designed to be a reference tool for your system. Please read the following safeguard and warnings carefully before you use this series product! Please keep this user’s manual well for future reference!
  • Page 3 Important Safeguards and Warnings 1．Electrical safety All installation and operation here should conform to your local electrical safety codes. The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited power source is rated 90-240V. We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation.
  • Page 4 7.Daily Maintenance Please shut down the device and then unplug the power cable before you begin daily maintenance work. Use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute the mild detergent first and then use it to clean the device.

  • Page 5: Table Of Contents

    Table of Contents General Introduction ....................1 Overview ....................1 Features ....................1 Framework ......................3 Appearance ....................3 Product Structure ..................3 Port ......................4 2.3.1 Device Wiring ..................4 2.3.2 Rear Panel ................... 5 Device Installation ....................8 Lens Installation ..................

  • Page 6: General Introduction

    1 General Introduction 1.1 Overview This product can monitor entrance/exit status and clearly snapshot vehicle plate in both day and night time. It can analyze and process plate snapshot. This series of product integrates video data capture and management as video surveillance of road monitoring core.
  • Page 7  Support peripheral equipment management, each peripheral equipment Peripheral control protocol and interface can be set freely.  Support activation devices such as vehicle detector. Equipment  ITC237-PW1B-IRZ：DC 12V / PoE power supply. Power  ITC237-PU1B-L, ITC237-PU1B-IR device：AC 24V / DC 12V / PoE Supplying power supply.

  • Page 8: Framework

    2 Framework 2.1 Appearance Figure 2-1 ITC237-PW1B-IRZ Figure 2-2 ITC237-PU1B-IR, ITC237-PU1B-L 2.2 Product Structure...

  • Page 9: Port

    Figure 2-3 ITC237-PW1B-IRZ Figure 2-4 ITC237-PU1B-IR, ITC237-PU1B-L 2.3 Port 2.3.1 Device Wiring Note: This figure is for ITC237-PW1B-IRZ.

  • Page 10: Rear Panel

    Figure 2-5 Port Function Connector Description Audio output AUDIO OUT Reserved port Audio input AUDIO IN Reserved port Ethernet Ethernet port Connect to standard Ethernet, provide PoE power. port I/O port Alarm signal input, output. See Chart 2-2. Input DC 12V，power supply must follow device label.
  • Page 11 Figure 2-6 Port Name Function VIDEO OUT Video output port Reserved Input AC 24V or DC 12V power supply, can supply at the AC 24V / DC 12V Power same time, only for camera, no lighting. System enanle －red indicator NO ...
  • Page 12 Chart 2-3...

  • Page 13: Device Installation

    3 Device Installation 3.1 Lens Installation Warning: Contents in this chapter are for ITC237-PU1B-IR, ITC237-PU1B-L only. Figure 3-1 3.1.1 Auto Iris Lend Installation Step 1. Remove device CMOS cover, face the lens at installation position on camera, clockwise rotate lens until it is in place. Step 2.

  • Page 14: Device Installation

    Step 3. Release the screwdriver that hold the slot. 3.2 Device Installation Warning: Contents in this chapter are for ITC237-PW1B-IRZ only. 3.2.1 (Optional) Install SD Card Note: When the device has SD card slot and needs SD card, you shall: Step 1.

  • Page 15: Optional) Install Network Port Waterproof Cover

    Figure 3-4 Step 1. Loosen adjusting screw with screw driver. Step 2. Adjust in up/down/left/right directions, set device direction according to need. Step 3. Fasten the screw. 3.2.3 (Optional) Install Network Port Waterproof Cover Note: This step is mandatory for outdoor device with standard waterproof cover. Figure 3-5 Step 1.

  • Page 17: System Network

    4 System Network Please refer to Figure for system connection. Figure 4-1...

  • Page 18: Quick Configuration Tool

    5 Quick Configuration Tool 5.1 Overview Quick configuration tool can search current IP address, modify IP address. At the same time, you can use it to upgrade the device. Please note the tool only applies to the IP addresses in the same segment. 5.2 Operation Step 1.
  • Page 19 Figure 5-2 Select the “Open Device Web” item; you can go to the corresponding web login interface. See Figure 5-3 Figure 5-3 If you want to modify the device IP address without logging in the device web interface, you can go to the configuration tool main interface to set.
  • Page 20 Figure 5-4 Figure 5-5 After you logged in, the configuration tool main interface is shown as below. See Figure 5-5 For detailed information and operation instruction of the quick configuration tool, please refer to the Quick Configuration Tool User’s Manual included in the resources CD.

  • Page 21: Web Operation

    6 Web Operation The device supports device access and management via WEB on PC. Note: Interface and settings here are for reference only. 6.1 First Time Log in Open IE and input HD intelligent traffic camera IP address in the address column. For example, if your IP is 192.168.1.108, then please input http:// 192.168.1.108 in IE address column.
  • Page 22 Figure 6-2 Security Settings Figure 6-3 Login Interface After installation, the interface is shown as below. See Please input your user name and password. Follow system instructions to change password, and click OK. Default factory name is admin and password is admin. Note: For security reasons, please modify your password after you first login.

  • Page 23: Non-First Time Login

    Note: Download and install plug-in if you cannot enter the homepage. Figure 6-4 Web Homepage 6.2 Non-first Time Login Step 1. Open IE and input HD intelligent traffic camera IP address in the address column. Step 2. Please input your user name and password. Click Login. 6.3 System Menu Figure 6-5 System Menu System menu is shown as in...
  • Page 24 Button Note Click this button, each parameter will resume to its latest saved parameter. After parameter is set, click this button to save. Chart 6-2...

  • Page 25: Technical Specification

    7 Technical Specification Parameter Parameter Name Value Type Model ITC237-PW1B-IRZ ITC237-PU1B-IR ITC237-PU1B-L Sensor 1/2.8 inch CMOS Shutter 1/50～1/10000 Min Illumination 0.002Lux/F1.2（color mode）；0 Lux/F1.2（B/W mode） Scan Progressive scanning Day/Night Mode Switch IR-CUT Camera Exposure Mode Full auto; customize range auto, customize Full auto;...
  • Page 26 Parameter Parameter Name Value Type ITC237-PU1B-IR, ITC237-PW1B-IRZ：built-in IR BLC  ITC237-PU1B-L：built-in white light BLC  ITC237-PU1B-IR ， ITC237-PU1B-L ： PoE+ power  Power supply ITC237-PW1B-IRZ：DC 12V/PoE power supply  ITC237-PU1B-IR, ITC237-PU1B-L：unit<17W（BLC all  on） General Consumption ITC237-PW1B-IRZ：unit<12W（12V power supply, IR ...

  • Page 27: Faq

    8 FAQ I cannot boot up Please click RESET button for at least five seconds to restore the device. factory default setup. SD card hot swap Before draw out SD card, please stop record or snapshot first and then wait for at least 15 seconds to remove the SD card. All the operations before is to maintain data integrity.

Table of Contents