Emerson Rosemount 3051SAL Reference Manual
  1. Manuals
  2. Brands
  3. Emerson Manuals
  4. Measuring Instruments
  5. Rosemount 3051SAL
  6. Reference manual

Emerson Rosemount 3051SAL Reference Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Reference Manual
00809-0200-4802, Rev BA
May 2013
Rosemount 3051S Wireless Series
Pressure, Level, and Flow Solutions with IEC 62951
(WirelessHART™) Protocol

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Rosemount 3051SAL and is the answer not in the manual?

Questions and answers

Related Manuals for Emerson Rosemount 3051SAL

Summary of Contents for Emerson Rosemount 3051SAL

  • Page 1 Reference Manual 00809-0200-4802, Rev BA May 2013 Rosemount 3051S Wireless Series Pressure, Level, and Flow Solutions with IEC 62951 (WirelessHART™) Protocol...
  • Page 3 Equipment service needs. 1 800 654 7768 (24 hours—includes Canada) Outside of these areas, contact your local Emerson Process Management representative. The products described in this document are NOT designed for nuclear-qualified applications. Using non-nuclear qualified products in applications that require nuclear-qualified hardware or products may cause inaccurate readings.
  • Page 4 Reference Manual 00809-0200-4802, Rev BA Failure to follow these installation guidelines could result in death or serious injury: Make sure only qualified personnel perform the installation.  Explosions could result in death or serious injury: Installation of this transmitter in an explosive environment must be in accordance with the appropriate local, national, and international standards, codes, and practices.

  • Page 5: Table Of Contents

    Reference Manual Table of Contents 00809-0200-4802, Rev BA May 2013 Table of contents 1Section 1: Introduction Using This Manual ............1 Models Covered .
  • Page 6 Reference Manual Table of Contents 00809-0200-4802, Rev BA May 2013 2.10.3Scaled Variable Configuration ........18 2.10.4Re-Mapping device variables .
  • Page 7 Reference Manual Table of Contents 00809-0200-4802, Rev BA May 2013 5Section 5: Operation and Maintenance Overview .............51 Calibration .
  • Page 8 Reference Manual Table of Contents 00809-0200-4802, Rev BA May 2013 B.1.1 Approved manufacturing locations....... 139 B.1.2 Telecommunication compliance .

  • Page 9: 1Section 1: Introduction

    Section 1: Introduction Reference Manual May 2013 00809-0200-4802, Rev BA Section 1 Introduction Using This Manual ............page 1 Models Covered .

  • Page 10: Models Covered

    Reference Manual Section 1: Introduction 00809-0200-4802, Rev BA May 2013 Models Covered The following Rosemount 3051S Wireless pressure transmitters are covered in this manual. ™ Rosemount 3051S Wireless Coplanar Pressure Transmitter Measurement Type Performance Class Differential Gage Absolute Classic Ultra Ultra for Flow –...

  • Page 11: Service Support

    00809-0200-4802, Rev BA May 2013 Service support To expedite the return process outside of the United States, contact the nearest Emerson Process Management representative. Within the United States, call the Emerson Process Management Instrument and Valves Response Center using the 1-800-654-RSMT (7768) toll-free number. This center, available 24 hours a day, will assist you with any needed information or materials.

  • Page 12: Product Recycling/Disposal

    Reference Manual Section 1: Introduction 00809-0200-4802, Rev BA May 2013 Product Recycling/Disposal Recycling of equipment and packaging should be taken into consideration and disposed of in accordance with local and national legislation/regulations. Introduction...

  • Page 13: Overview

    Section 2: Configuration Reference Manual May 2013 00809-0200-4802, Rev BA Section 2 Configuration Overview ............. . . page 5 Safety Messages .

  • Page 14: Warnings ()

    Verify the latest Device Driver (DD/DTM) is loaded on your systems to ensure proper  communications. Download the latest DD at www.emersonprocess.com. 2. In the Browse by Member dropdown menu, select Rosemount business unit of Emerson Process Management. 3. Select desired Product Within...

  • Page 15: Required Bench Top Configuration

    Reference Manual Section 2: Configuration 00809-0200-4802, Rev BA May 2013 Table 2-1. Rosemount 3051S Wireless Device Revisions and files Review Review Identify Device Find Device Driver Instructions Functionality NAMUR HART HART Manual Software Software Software Universal Device Document Changes to Release Date Revision Revision...

  • Page 16: Device Network Configuration

    Reference Manual Section 2: Configuration 00809-0200-4802, Rev BA May 2013 Field Hook-up Figure 2-1 illustrates the wiring for a field hook-up with a Field Communicator or AMS. The Field Communicator or AMS may be connected at “COMM” on the transmitter terminal block. Figure 2-1.

  • Page 17: Configure Update Rate

    Reference Manual Section 2: Configuration 00809-0200-4802, Rev BA May 2013 2.5.2 Configure update rate Fast Keys 2, 1, 4 The Update Rate is the frequency at which a new measurement is taken and transmitted over the wireless network. This by default is 1 minute. This may be changed at commissioning, or at any time via AMS Wireless Configurator.

  • Page 18: Review Configuration Data

    Reference Manual Section 2: Configuration 00809-0200-4802, Rev BA May 2013 Review configuration data The following is a list of factory default configurations that can be viewed by using the Field Communicator or AMS. Follow the steps below to review the transmitter configuration information.

  • Page 19: Review Device And Sensor Information

    Reference Manual Section 2: Configuration 00809-0200-4802, Rev BA May 2013 2.6.2 Review Device and Sensor Information Fast Keys 2, 2, 9 To view device information: From the Home screen, choose 2: Configure. Choose 2: Manual Setup. Choose 9: Device Information. Choose from the corresponding number to view each field: Identification Revisions...

  • Page 20: Review Radio Information

    Reference Manual Section 2: Configuration 00809-0200-4802, Rev BA May 2013 2.6.3 Review radio information Fast Keys 2, 2, 9, 3 To view radio information: From the Home screen, choose 2: Configure. Choose 2: Manual Setup. Choose 9: Device Information. Choose 3: Radio. Select from the corresponding number to view each field: Manufacturer Device Type...

  • Page 21: Basic Setup

    Reference Manual Section 2: Configuration 00809-0200-4802, Rev BA May 2013 The Operating Parameters menu displays the following information pertaining to the device: Percent of Range  Pressure  Pressure Status  Sensor Temperature  Sensor Temperature Status  Electronics Temperature ...

  • Page 22: Set Transfer Function

    Reference Manual Section 2: Configuration 00809-0200-4802, Rev BA May 2013 2.8.2 Set transfer function Fast Keys 2, 2, 4, 2 The Rosemount 3051S Wireless has two output settings: Linear and Square Root. Activate the square root output option to make output proportional to flow. As input approaches zero, the 3051S Wireless automatically switches to linear output in order to ensure a more smooth, stable output near zero (see Figure...

  • Page 23: Damping

    Reference Manual Section 2: Configuration 00809-0200-4802, Rev BA May 2013 2.8.3 Damping Fast Keys 2, 2, 2, 4 The Damping command introduces a delay in processing which increases the response time of the transmitter; smoothing variations in output readings caused by rapid input changes. In the 3051S Wireless pressure transmitter, damping only takes effect when the device is placed in high power refresh mode and during calibration.

  • Page 24: Lcd Display

    Reference Manual Section 2: Configuration 00809-0200-4802, Rev BA May 2013 LCD display 2.9.1 LCD display configuration Fast Keys 2, 1, 5 The LCD display indicates output and abbreviated diagnostic messages. Note Use Rosemount Wireless LCD Part Number: 00753-9004-0002. The LCD display features a four-line display and a bar graph. The first line of five characters displays the output description, the second line of seven digits displays the actual value, the third line of six characters displays engineering units and the fourth line displays “Error”...

  • Page 25: Detailed Setup

    Reference Manual Section 2: Configuration 00809-0200-4802, Rev BA May 2013 2.10 Detailed setup 2.10.1 Configure process alarms Fast Keys 2, 1, 6 Alerts allow the user to configure the transmitter to output a HART message when the configured data point is exceeded. A process alert will be transmitted continuously if the set points are exceeded and the alert mode is ON.

  • Page 26: 2Sensor Temperature Unit

    Reference Manual Section 2: Configuration 00809-0200-4802, Rev BA May 2013 2.10.2 Sensor temperature unit Fast Keys 2, 2, 8, 3 The Sensor Temperature Unit command selects between Celsius and Fahrenheit units for the sensor temperature. The sensor temperature output is accessible via HART only. To select the sensor temperature unit: From the Home screen, choose 2: Configure.
  • Page 27 Reference Manual Section 2: Configuration 00809-0200-4802, Rev BA May 2013 Note If Scaled Variable is mapped as the primary variable and square root mode is selected, ensure transfer function is set to linear. Refer to “Set transfer function” on page Field Communicator v3.3 To configure the scaled variable with a Field Communicator, perform the following procedure: From the HOME screen follow the fast key sequence “Scaled Variable Configuration.”...
  • Page 28 Reference Manual Section 2: Configuration 00809-0200-4802, Rev BA May 2013 Enter linear offset value in scaled variable (custom) units (If performing a Linear Function). Skip to step 11. Enter Low Flow cutoff mode (If performing a Square Root Function) Choose OFF if a low flow cutoff value is not desired. b.
  • Page 29 Reference Manual Section 2: Configuration 00809-0200-4802, Rev BA May 2013 DP Level example Figure 2-3. Example tank 20 mA 230 in. 0.94 sg 200 in. 4 mA 12 in. A differential transmitter is used in a level application where the span is 188 inH O (200 in.

  • Page 30: 4Re-Mapping Device Variables

    Reference Manual Section 2: Configuration 00809-0200-4802, Rev BA May 2013 value is 1000 gallons of water per hour. Based on this information, the Scaled Variable configuration would be as follows: Scaled Variable units: gal/h Scaled data options: square root Pressure value position 125 inH2O (311 mbar) Scaled Variable position 20,000 gal/h (75,708...

  • Page 31: Diagnostics And Service

    Reference Manual Section 2: Configuration 00809-0200-4802, Rev BA May 2013 Re-mapping using a Field Communicator From the HOME screen, enter the fast key sequence 2, 1, 7 Fast Keys: guided set up 2, 2, 3, 5 Fast Keys: manual set up Re-mapping using AMS Device Manager Right click on the device and select Configure.

  • Page 32: 2Join Status

    Reference Manual Section 2: Configuration 00809-0200-4802, Rev BA May 2013 2.11.2 Join status Fast Keys 3, 4, 1 To view the join status of the device, perform the following procedure: From the Home screen, choose 3: Service Tools. Choose 4: Communications. Choose 1: Join Status.

  • Page 33: Advanced Functions For Hart Protocol

    Reference Manual Section 2: Configuration 00809-0200-4802, Rev BA May 2013 2.12 Advanced functions for HART Protocol 2.12.1 Saving, recalling, and cloning configuration data Fast Keys left arrow, 1, 2 Use the cloning feature of the Field Communicator or the AMS “User Configuration” feature to configure several 3051S Wireless transmitters similarly.
  • Page 34 Reference Manual Section 2: Configuration 00809-0200-4802, Rev BA May 2013 When finished, the Field Communicator informs you of the status. Repeat Steps through configure another transmitter. Note The transmitter receiving cloned data must have the same software version (or later) as the original transmitter.

  • Page 35: Overview

    Section 3: Installation Reference Manual May 2013 00809-0200-4802, Rev BA Section 3 Installation Overview ............. . . page 27 Safety messages .

  • Page 36: Warnings ()

    Reference Manual Section 3: Installation 00809-0200-4802, Rev BA May 2013 3.2.1 Warnings ( ) Failure to follow these installation guidelines could result in death or serious injury. Make sure only qualified personnel perform the installation.  Explosions can result in death or serious injury. Installation of this transmitter in an explosive environment must be in accordance with the appropriate local, national, and international standards, codes, and practices.

  • Page 37: Considerations

    Reference Manual Section 3: Installation 00809-0200-4802, Rev BA May 2013 Considerations 3.3.1 General Measurement performance depends upon proper installation of the transmitter and impulse piping. Mount the transmitter close to the process and use a minimum of piping to achieve best performance.

  • Page 38: Mechanical

    Reference Manual Section 3: Installation 00809-0200-4802, Rev BA May 2013 Figure 3-2. Conduit Plug Location Conduit Plug Conduit Plug Field Communicator connections In order for the Field Communicator to interface with the Rosemount 3051S, the Power Module must be connected. Figure 3-3.
  • Page 39 Reference Manual Section 3: Installation 00809-0200-4802, Rev BA May 2013 Figure 3-4. Installation Flowchart START HERE Bench Calibration? Field Install Check Switches page 39 Configure Verify Mount Transmitter Review Install Power Set Units Transmitter Module Configuration (pages – Check Process Set Range Connection Points...

  • Page 40: Installation Procedures

    Reference Manual Section 3: Installation 00809-0200-4802, Rev BA May 2013 Installation procedures For dimensional drawing information refer to “Dimensional Drawings” on page Process flange orientation Mount the process flanges with sufficient clearance for process connections. For safety reasons, place the drain/vent valves so the process fluid is directed away from possible human contact when the vents are used.
  • Page 41 Alloy K-500 Head Marking Bolt Installation Only use bolts supplied with the Rosemount 3051S or sold by Emerson Process Management as spare parts. When installing the transmitter to one of the optional mounting brackets, torque the bolts to 125 in-lb. (0,9 N-m). Use the following bolt installation procedure: Finger-tighten the bolts.
  • Page 42 Reference Manual Section 3: Installation 00809-0200-4802, Rev BA May 2013 GAGE/ABSOLUTE TRANSMITTER DIFFERENTIAL TRANSMITTER Drain/Vent Plug Drain/Vent Drain/Vent 1.75 (44) x 4 1.75 (44) x 4 1.50 (38) x 4 1.50 (38) x 4 Note Dimensions are in inches (millimeters). Installation...
  • Page 43 Reference Manual Section 3: Installation 00809-0200-4802, Rev BA May 2013 Transmitter with Transmitter with Flange Adapters Flange Bolts and Flange/ Adapter Bolts 2.88 (73) x 4 1.75 (44) x 4 Description Size in in. (mm) Differential Pressure Flange Bolts 1.75 (44) Adapter Bolts 1.50 (38) Flange/ Adapter Bolts...
  • Page 44 Reference Manual Section 3: Installation 00809-0200-4802, Rev BA May 2013 Impulse piping The piping between the process and the transmitter must accurately transfer the pressure to obtain accurate measurements. There are five possible sources of error: leaks, friction loss (particularly if purging is used), trapped gas in a liquid line, liquid in a gas line, and density variations between the legs.
  • Page 45 Reference Manual Section 3: Installation 00809-0200-4802, Rev BA May 2013 Mounting requirements Refer to Figure 3-5 for examples of the following mounting configurations: Liquid flow measurement Place taps to the side of the line to prevent sediment deposits on the process isolators. ...

  • Page 46: Process Connections

    Reference Manual Section 3: Installation 00809-0200-4802, Rev BA May 2013 3.4.2 Process connections Rosemount 3051S Wireless transmitter flange process connection size is –18 NPT. Flange adapters with –14 NPT connections are available as the D2 option. Use your plant-approved lubricant or sealant when making the process connections. The process connections on the transmitter flange are on 2 -inch (54 mm) centers to allow direct mounting to a three-valve or five-valve manifold.

  • Page 47: Consider Housing Rotation

    Reference Manual Section 3: Installation 00809-0200-4802, Rev BA May 2013 3.4.3 Consider housing rotation The housing can be rotated to improve field access to wiring or to better view the optional LCD display. Perform the following procedure: Figure 3-6. Housings ®...

  • Page 48: Power Module Installation

    Reference Manual Section 3: Installation 00809-0200-4802, Rev BA May 2013 3.4.6 Power module installation Figure 3-7. Power Module Installation Wireless Power Module Installation To make connections, perform the following procedure: Note This transmitter uses the Black Power Module. Please order model number 701PBKKF or spare part number 00753-9200-0001.

  • Page 49: Rosemount 304, 305 And 306 Integral Manifolds

    Reference Manual Section 3: Installation 00809-0200-4802, Rev BA May 2013 Use the following procedure and Figure 3-8 to install the LCD display: Remove the back cover and Power Module. Remove the transmitter cover opposite the field terminal side. Do not remove the instrument covers in explosive environments when the circuit is live.

  • Page 50: Rosemount 305 Integral Manifold Installation Procedure

    Reference Manual Section 3: Installation 00809-0200-4802, Rev BA May 2013 Figure 3-9. Integral Manifold Designs TRADITIONAL IN-LINE CONVENTIONAL COPLANAR 3.5.1 Rosemount 305 Integral Manifold installation procedure To install a 305 Integral Manifold to a Rosemount 3051S Wireless transmitter: Inspect the Teflon SuperModule O-rings. If the O-rings are undamaged, reusing them is recommended.

  • Page 51: Rosemount 304 Conventional Manifold Installation Procedure

    Reference Manual Section 3: Installation 00809-0200-4802, Rev BA May 2013 Place transmitter into holding fixture. Apply appropriate thread paste or tape to threaded instrument end of the manifold. Count total threads on the manifold before starting assembly. Start turning the manifold by hand into the process connection on the transmitter. Note If using thread tape, be sure the thread tape does no strip when the manifold assembly is started.
  • Page 52 Reference Manual Section 3: Installation 00809-0200-4802, Rev BA May 2013 Three and five-valve configurations shown: In normal operation the two block valves between the process and Drain/ instrument ports will be open and the Drain/ Vent Vent equalizing valve will be closed. Valve Valve Equalize...
  • Page 53 Reference Manual Section 3: Installation 00809-0200-4802, Rev BA May 2013 Five-valve Natural Gas configurations shown: In normal operation, the two block valves between the process and instrument ports will be open, and the Test Test equalizing valves will be closed. (Plugged) (Plugged) Equalize...
  • Page 54 Reference Manual Section 3: Installation 00809-0200-4802, Rev BA May 2013 Open the equalize valve on the low pressure (downstream) side of the Test Test transmitter. The manifold is (Plugged) (Plugged) now in the proper Equalize Equalize configuration for zeroing the (open) (open) transmitter.

  • Page 55: 4Section 4: Commissioning

    Section 4: Commissioning Reference Manual May 2013 00809-0200-4802, Rev BA Section 4 Commissioning Safety messages ............page 47 Network status .

  • Page 56: Network Status

    Reference Manual Section 4: Commissioning 00809-0200-4802, Rev BA May 2013 Network status If the Rosemount 3051S Wireless was configured with the Network ID and Join Key and sufficient time for network polling has passed, the transmitter should be connected to the network.
  • Page 57 Reference Manual Section 4: Commissioning 00809-0200-4802, Rev BA May 2013 Figure 4-1. Diagnostic Screen Sequence Device ID Network ID Network Join Device Status Status S u p l y n e t w k A b c d e i d - 1 2 n e t w k 7.
  • Page 58 Reference Manual Section 4: Commissioning 00809-0200-4802, Rev BA May 2013 A green status indicator means that the device is working properly. A red indicator means that there is a problem with either the device or its communication path. For more detail on a specific device, click on the tag name.

  • Page 59: 5Section 5: Operation And Maintenance

    Section 5: Operation and Maintenance Reference Manual May 2013 00809-0200-4802, Rev BA Section 5 Operation and Maintenance Overview ............. . . page 51 Calibration .

  • Page 60: Sensor Trim Overview

    Reference Manual Section 5: Operation and Maintenance 00809-0200-4802, Rev BA May 2013 Table 5-1. Recommended Calibration Tasks Transmitter Bench Calibration Tasks Field Calibration Tasks Set output configuration parameters: Reconfigure parameters if necessary. 3051S 2CD 3051S 2CG Set the % range points. 3051S 2L Zero trim the transmitter to b.

  • Page 61: Zero Trim

    Reference Manual Section 5: Operation and Maintenance 00809-0200-4802, Rev BA May 2013 Sensor trim is a two-point sensor calibration where two end-point pressures are applied, and all output is linearized between them. Always adjust the low trim value first to establish the correct offset.

  • Page 62: Line Pressure Effect (Range 2 And Range 3)

    Reference Manual Section 5: Operation and Maintenance 00809-0200-4802, Rev BA May 2013 Note Select pressure input values so that lower and upper values are equal to or outside the Lower and Upper Operating points. Do not attempt to obtain reverse output by reversing the high and low points.
  • Page 63 Reference Manual Section 5: Operation and Maintenance 00809-0200-4802, Rev BA May 2013 For line pressures above 2000 psi (138 bar), the zero effect error is ± 0.2% of the upper range limit plus an additional ± 0.2% of upper range limit error for each 1000 psi (69 bar) of line pressure above 2000 psi (138 bar).
  • Page 64 Reference Manual Section 5: Operation and Maintenance 00809-0200-4802, Rev BA May 2013 LT = 506 inH O (1.26 bar) To calculate the high trim (HT) value: HT = 1500 + (0.01/1000)(1500)(1200) HT = 1518 inH O (3.78 bar) Complete a Rosemount 3051S Wireless sensor trim and enter the corrected values for low trim (LT) and high trim (HT), refer to “Sensor trim”...

  • Page 65: Lcd Screen Messages

    Reference Manual Section 5: Operation and Maintenance 00809-0200-4802, Rev BA May 2013 LCD screen messages 5.3.1 Startup screen sequence The following screens will display when the Power Module is first connected to the Rosemount 3051S Wireless. X X X X X All Segments On: used to visually determine if there X X X X x x x are any bad segments on the LCD...
  • Page 66 Reference Manual Section 5: Operation and Maintenance 00809-0200-4802, Rev BA May 2013 S N S R SV Screen - sensor temperature value 2 5. 0 0 d e g c D E V TV Screen - device temperature value 2 5. 2 5 d e g c S u p l y QV Screen - voltage reading at the power supply...

  • Page 67: Diagnostic Button Screen Sequence

    Reference Manual Section 5: Operation and Maintenance 00809-0200-4802, Rev BA May 2013 5.3.2 Diagnostic Button Screen Sequence The following five screens will display when the device is operating properly and the Diagnostic Button has been pressed. Device Information - Tag: user entered tag which is A b c d e eight characters long - will not display if all characters are blank...

  • Page 68: Network Diagnostic Status Screens

    Reference Manual Section 5: Operation and Maintenance 00809-0200-4802, Rev BA May 2013 S u p l y Diagnostic Button Screen 5: voltage reading at the 7. 2 1 power supply terminals v o l t s 5.3.3 Network diagnostic status screens These screens display the network status of the device.
  • Page 69 Reference Manual Section 5: Operation and Maintenance 00809-0200-4802, Rev BA May 2013 Diagnostic Button Screen 4.4: the device is in a n e t w k disconnected state and requires a “Force Join” command to join the network D I S C N T Diagnostic Button Screen 4.5: the device is N E T w K searching for the Network...
  • Page 70 Reference Manual Section 5: Operation and Maintenance 00809-0200-4802, Rev BA May 2013 Diagnostic Button Screen 4.9: the device has n e t w k joined a network and has been fully configured and has multiple parents Operation and Maintenance...

  • Page 71: Device Diagnostic Screens

    Reference Manual Section 5: Operation and Maintenance 00809-0200-4802, Rev BA May 2013 5.3.4 Device diagnostic screens The following screens will show the device diagnostics depending on the state of the device. Device Information - Status: there is a critical error D E V which may prevent the device from operating correctly.
  • Page 72 Reference Manual Section 5: Operation and Maintenance 00809-0200-4802, Rev BA May 2013 S u p l y QV Screen - voltage reading at the power supply 7. 2 1 terminals v o l t s P R C N T Percent Range Screen - percent range reading 7.
  • Page 73 Reference Manual Section 5: Operation and Maintenance 00809-0200-4802, Rev BA May 2013 Diagnostic Button Screen 7.1: the terminal voltage has dropped below level of operating limit. Replace s u p l y the Power Module (Part Number: 00753-9220-0001) f a i l u r Diagnostic Button Screen 7.2: the terminal voltage is below the recommended operating range - if this is s u p l y...
  • Page 74 Reference Manual Section 5: Operation and Maintenance 00809-0200-4802, Rev BA May 2013 Diagnostic Button Screen 10.1: a sensor attached to the transmitter has failed, and valid readings from that sensor are no longer possible - check the sensor s n s r and sensor wiring connections - check additional status for more detailed information of the failure source...

  • Page 75: Overview

    Section 6: Troubleshooting Reference Manual May 2013 00809-0200-4802, Rev BA Section 6 Troubleshooting Overview ............. . . page 67 Safety messages .

  • Page 76: Warnings ()

    Reference Manual Section 6: Troubleshooting 00809-0200-4802, Rev BA May 2013 6.2.1 Warnings ( ) Explosions can result in death or serious injury. Before connecting a 375 Field Communicator in an explosive atmosphere, make sure  that the instruments are installed according to intrinsically safe or nonincendive field wiring practices.
  • Page 77 Reference Manual Section 6: Troubleshooting 00809-0200-4802, Rev BA May 2013 Device Status Description Recommended Action Check process for possible saturation condition Pressure has The sensor has exceeded the Exceeded Limits maximum measurement range. Verify that the appropriate sensor was chosen for the application Reconfirm sensor configuration Reset the device...
  • Page 78 Reference Manual Section 6: Troubleshooting 00809-0200-4802, Rev BA May 2013 Device Status Description Recommended Action Verify that the process variable is within user LO Alarm The primary variable has surpassed the user defined limit. specified limits Reconfirm the user defined alarm limit If not needed, disable this alert Verify that the process variable is within user LO LO Alarm...
  • Page 79 Reference Manual Section 6: Troubleshooting 00809-0200-4802, Rev BA May 2013 Table 6-2. Rosemount 3051S Wireless Troubleshooting Symptom Recommended Actions Transmitter will not respond to changes in Check test equipment applied pressure Check impulse piping or manifold for blockage Verify applied pressure is within sensor limits Digital Pressure Variable reading is low or Check test equipment (verify accuracy) high...

  • Page 80: Disassembly Procedures

    Reference Manual Section 6: Troubleshooting 00809-0200-4802, Rev BA May 2013 Disassembly procedures 6.3.1 Remove from service Be aware of the following: Follow all plant safety rules and procedures.  Isolate and vent the process from the transmitter before removing the transmitter from ...

  • Page 81: Removing The Feature Assembly And The Supermodule From The Housing73

    Reference Manual Section 6: Troubleshooting 00809-0200-4802, Rev BA May 2013 6.3.3 Removing the feature assembly and the SuperModule from the housing The Wireless Feature Board is located in the electronics compartment. To remove the assembly, perform the following procedure. Remove the housing cover opposite the field terminal side. Remove the LCD Display, if applicable.

  • Page 82: Reassembly Procedures

    Reference Manual Section 6: Troubleshooting 00809-0200-4802, Rev BA May 2013 Important To prevent damage to the SuperModule cable, disconnect it from the PlantWeb assembly before you remove the SuperModule from the housing. Loosen the housing rotation set screw with a -inch hex wrench, then rotate back one full turn.

  • Page 83: Reassemble The Process Flange

    Reference Manual Section 6: Troubleshooting 00809-0200-4802, Rev BA May 2013 6.4.3 Reassemble the process flange Inspect the Teflon SuperModule o-rings. If the o-rings are not damaged, reuse them. Replace o-rings that show any signs of damage, such as nicks, cuts, or general wear. Note If you are replacing the o-rings, be careful not to scratch the o-ring grooves or the surface of the isolating diaphragm when removing the damaged o-rings.
  • Page 84 Reference Manual Section 6: Troubleshooting 00809-0200-4802, Rev BA May 2013 Table 6-4. Bolt Installation Torque Values Bolt Material Initial Torque Value Final Torque Value CS-ASTM-A445 Standard 300 in-lb. (34 N-m) 650 in-lb. (73 N-m) 316 SST—Option L4 150 in-lb. (17 N-m) 300 in-lb.

  • Page 85: Specifications

    Appendix A: Specifications and reference data Reference Manual May 2013 00809-0200-4802, Rev BA Appendix A Specifications and Reference Data Performance specifications ..........page 77 Functional specifications .
  • Page 86 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Reference accuracy (1)(2) Models Ultra Classic Ultra for Flow 3051S_CD, CG Ranges 2 - 4 ±0.025% of span. ±0.055% of span. ±0.04% of reading up to 8:1 For spans less than 10:1, For spans less than 10:1, DP turndown from URL;...
  • Page 87 (1) Warranty details can be found in Emerson Process Management Terms & Conditions of Sale, Document 63445, Rev G (10/06). (2) Rosemount Ultra and Ultra for Flow transmitters have a limited warranty of twelve (12) years from date of shipment. All other provisions of Emerson Process Management standard limited warranty remain the same.
  • Page 88 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Ambient temperature effect Models Ultra Classic Ultra for Flow 3051S_CD, CG per 50 °F (28 °C) per 50 °F (28 °C) per 50 °F (28 °C) Range 2 - 5 ±...
  • Page 89 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Line pressure effect Models Ultra and Ultra for Flow Classic 3051S_CD Zero Error Zero Error ± 0.025% URL per 1000 psi (69 bar) ± 0.05% URL per 1000 psi (69 bar) Range 2 - 3 ±...

  • Page 90: Functional Specifications

    Appendix A: Specifications and reference data Reference Manual May 2013 00809-0200-4802, Rev BA A.1.2 Functional specifications Range and sensor limits 3051S_ Minimum Span 3051S_ Range and Sensor Limits Ultra and Classic Upper (URL) Lower (LRL) Ultra for (3)(4) 3051S_CD 3051S_CG, LG 3051S_LD Flow 0.1 inH...
  • Page 91 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Wireless Self-Organizing Networks Output IEC 62591 (WirelessHART), 2.4 GHz DSSS. Local display The optional five-digit LCD can display user-selectable information such as primary variable in engineering units, percent of range, sensor module temperature, and electronics temperature. The display updates based on the wireless update rate.
  • Page 92 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Rosemount 3051S_T Range 1: 750 psi (51,7 bar) Range 2: 1500 psi (103,4 bar) Range 3: 1600 psi (110,3 bar) Range 4: 6000 psi (413,7 bar) Range 5: 15000 psi (1034,2 bar) Rosemount 3051S_L Limit is flange rating or sensor rating, whichever is lower (see the table below).
  • Page 93 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Temperature limits Ambient –40 to 185 °F (–40 to 85 °C) With LCD display : –40 to 175 °F (–40 to 80 °C) With option code P0: –20 to 185 °F (–29 to 85 °C) (1) LCD display may not be readable and LCD updates will be slower at temperatures below -4 °F (-20 °C).
  • Page 94 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Humidity limits 0–100% relative humidity Volumetric displacement Less than 0.005 in (0,08 cm Damping The Damping command introduces a delay in processing which increases the response time of the transmitter;...

  • Page 95: Physical Specifications

    Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 A.1.3 Physical specifications Electrical connections –14 NPT, G , and M20 x 1.5 (CM20) conduit. HART interface connections fixed to terminal block. Process connections Rosemount 3051S_C –18 NPT on 2 -in.
  • Page 96 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Wetted O-rings Glass-filled PTFE (Graphite-filled PTFE with Isolating Diaphragm code 6) Rosemount 3051S_L process wetted parts Flanged Process Connection (Transmitter High Side) Process diaphragms, including process gasket surface 316L SST, Alloy C-276, or Tantalum Extension CF-3M (Cast 316L SST, material per ASTM A743), or CW-12MW (Cast C-276, material ASTM...
  • Page 97 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Sensor module fill fluid Silicone or inert halocarbon (Inert is not available with 3051S_CA). In-Line series uses ® Fluorinert FC-43. Process fill fluid (liquid level only) 3051S_L: Syltherm XLT, D.C. Silicone 704, D.C.
  • Page 98 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Shipping weights for Rosemount 3051S Wireless Pressure Transmitter Table A-1. SuperModule Platform weights SuperModule Platform Weight in lb. (kg) Coplanar 3.1 (1,4) In-Line 1.4 (0,6) (1) Flange and bolts not included. Table A-2.
  • Page 99 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Option Code Option Add lb (kg) Level Flange—2 in., 300 8.2 (3,7) DIN Level Flange, SST, DN 50, PN 40 7.8 (3,5) DIN Level Flange, SST, DN 80, PN 40 13.0 (5,9) (1) Includes LCD display and display cover.

  • Page 100: Dimensional Drawings

    Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Dimensional drawings Dimensions are in inches (millimeters). Process adapters (option D2) and Rosemount 305 integral manifolds must be ordered with the transmitter. Wireless PlantWeb Housing with In-Line and Coplanar SuperModule Platform Extended Range, External Antenna 90°...
  • Page 101 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Table A-5. 3051S_L Dimensional Specifications Except where indicated, dimensions are in inches (millimeters). Class Pipe Flange Bolt Circle Outside No. of Bolt Hole Extension O.D. Size Thickness A Diameter Diameter Bolts...

  • Page 102: Ordering Information

    Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Ordering Information Table A-6. Rosemount 3051S Coplanar Differential, Gage, or Absolute Transmitter ★ The Standard offering represents the most common models and options. These options should be selected for best delivery. __The Expanded offering is subject to additional delivery lead time.
  • Page 103 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Expanded Alloy 400 Tantalum Gold-Plated Alloy 400 (includes Graphite-Filled PTFE o-ring) Gold-plated 316L SST Process Connection Size Material Type Flange Drain Vent Bolting Material Standard Standard ★ None ★...
  • Page 104 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 ★ Traditional flange 316 SST ★ Traditional flange Cast C-276 Alloy C-276 ★ Traditional flange Cast Alloy Alloy 400/K-500 ★ Traditional flange Alloy C-276 ★ DIN-compliant traditional –18 NPT 316 SST -in.
  • Page 105 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 ★ Junction Box housing –14 NPT ★ Junction Box Housing with output for remote display and interface Aluminum –14 NPT ★ Junction Box Housing with output for remote display and interface Aluminum M20 x 1.5 ★...
  • Page 106 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 PlantWeb Enhanced Measurement Functionality Standard Standard (15) ★ fieldbus Fully Compensated Mass Flow Block OUNDATION (16) Mounting Bracket Standard Standard ★ Coplanar flange bracket, all SST, 2-in. pipe and panel ★...
  • Page 107 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Custody Transfer Standard Standard (19) ★ Measurement Canada Accuracy Approval External Ground Screw Assembly Standard Standard ★ External ground screw assembly Drain/Vent Valve Standard Standard (16) ★ Delete transmitter drain/vent valves (install plugs) Expanded (16)
  • Page 108 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 ★ INMETRO Intrinsic Safety ★ INMETRO Flameproof, Intrinsic Safety ★ China Flameproof ★ China Intrinsic Safety (22) ★ ATEX and CSA Flameproof, Intrinsically Safe, Division 2 (22) ★...
  • Page 109 (12) Available with output code A only. Available approvals are FM Intrinsically Safe, Division 2 (option code I5), ATEX Intrinsic Safety (option code I1), or IECEx Intrinsic Safety (option code I7). Contact an Emerson Process Management representative for additional information.
  • Page 110 00809-0200-4802, Rev BA May 2013 (19) Requires PlantWeb housing and Hardware Adjustments option code D1. Limited availability depending on transmitter type and range. Contact an Emerson Process Management representative for additional information. (20) Transmitter is shipped with 316 SST conduit plug (uninstalled) in place of standard carbon steel conduit plug.
  • Page 111 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Process Connection Size Material Type Flange Drain Bolting Material Vent Standard Standard ★ Assemble to Rosemount 306 Integral Manifold (7)(5)(6) ★ Assemble to one Rosemount 1199 Diaphragm Seal ★...
  • Page 112 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Expanded PlantWeb housing Aluminum PlantWeb housing Junction Box housing Aluminum Junction Box Housing with output for remote display and Aluminum interface Wireless Options (Requires option code X and wireless PlantWeb housing) Update Rate Standard Standard...
  • Page 113 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Alarm Limit Standard Standard (17) ★ NAMUR alarm and saturation levels, high alarm (17) ★ NAMUR alarm and saturation levels, low alarm (17) ★ Custom alarm and saturation signal levels, high alarm (Requires C1 and Configuration Data Sheet) (17) ★...
  • Page 114 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 ★ IECEx Flameproof, Dust Ignition-proof ★ IECEx Intrinsic Safety ★ IECEx FISCO Intrinsic Safety (F fieldbus protocol only) OUNDATION ★ IECEx Type n ★ IECEx Flameproof, Dust Ignition-proof, Intrinsic Safety, Type n ★...
  • Page 115 (13) Not available with housing style codes 00, 01, 2E, 2F, 2G, 2M, 5A, or 7J. (14) Requires PlantWeb housing and Hardware Adjustments option code D1. Limited availability depending on transmitter type and range. Contact an Emerson Process Management representative for additional information.
  • Page 116 Appendix A: Specifications and reference data Reference Manual May 2013 00809-0200-4802, Rev BA Table A-8. Rosemount 3051SFA Annubar Flowmeter Ordering Information ★ The Standard offering represents the most common models and options. These options should be selected for best delivery. __The Expanded offering is subject to additional delivery lead time.
  • Page 117 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Table A-8. Rosemount 3051SFA Annubar Flowmeter Ordering Information ★ The Standard offering represents the most common models and options. These options should be selected for best delivery. __The Expanded offering is subject to additional delivery lead time.
  • Page 118 Appendix A: Specifications and reference data Reference Manual May 2013 00809-0200-4802, Rev BA Table A-8. Rosemount 3051SFA Annubar Flowmeter Ordering Information ★ The Standard offering represents the most common models and options. These options should be selected for best delivery. __The Expanded offering is subject to additional delivery lead time.
  • Page 119 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Table A-8. Rosemount 3051SFA Annubar Flowmeter Ordering Information ★ The Standard offering represents the most common models and options. These options should be selected for best delivery. __The Expanded offering is subject to additional delivery lead time.
  • Page 120 Appendix A: Specifications and reference data Reference Manual May 2013 00809-0200-4802, Rev BA Table A-8. Rosemount 3051SFA Annubar Flowmeter Ordering Information ★ The Standard offering represents the most common models and options. These options should be selected for best delivery. __The Expanded offering is subject to additional delivery lead time.
  • Page 121 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Table A-8. Rosemount 3051SFA Annubar Flowmeter Ordering Information ★ The Standard offering represents the most common models and options. These options should be selected for best delivery. __The Expanded offering is subject to additional delivery lead time.
  • Page 122 Appendix A: Specifications and reference data Reference Manual May 2013 00809-0200-4802, Rev BA Table A-8. Rosemount 3051SFA Annubar Flowmeter Ordering Information ★ The Standard offering represents the most common models and options. These options should be selected for best delivery. __The Expanded offering is subject to additional delivery lead time.
  • Page 123 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Table A-8. Rosemount 3051SFA Annubar Flowmeter Ordering Information ★ The Standard offering represents the most common models and options. These options should be selected for best delivery. __The Expanded offering is subject to additional delivery lead time.
  • Page 124 (12) Available with output code A only. Available approvals are FM Intrinsically Safe, Division 2 (option code I5), ATEX Intrinsic Safety (option code I1), or IECEx Intrinsic Safety (option code I7). Contact an Emerson Process Management representative for additional information.
  • Page 125 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Table A-9. Rosemount 3051SFC Compact Orifice Flowmeter Ordering Information ★ The Standard offering represents the most common models and options. These options should be selected for best delivery. __The Expanded offering is subject to additional delivery lead time.
  • Page 126 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Table A-9. Rosemount 3051SFC Compact Orifice Flowmeter Ordering Information ★ The Standard offering represents the most common models and options. These options should be selected for best delivery. __The Expanded offering is subject to additional delivery lead time.
  • Page 127 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Table A-9. Rosemount 3051SFC Compact Orifice Flowmeter Ordering Information ★ The Standard offering represents the most common models and options. These options should be selected for best delivery. __The Expanded offering is subject to additional delivery lead time.
  • Page 128 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Table A-9. Rosemount 3051SFC Compact Orifice Flowmeter Ordering Information ★ The Standard offering represents the most common models and options. These options should be selected for best delivery. __The Expanded offering is subject to additional delivery lead time.
  • Page 129 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Table A-9. Rosemount 3051SFC Compact Orifice Flowmeter Ordering Information ★ The Standard offering represents the most common models and options. These options should be selected for best delivery. __The Expanded offering is subject to additional delivery lead time.
  • Page 130 (11) Available with output code A only. Available approvals are FM Intrinsically Safe, Division 2 (option code I5), ATEX Intrinsic Safety (option code I1), or IECEx Intrinsic Safety (option code I7). Contact an Emerson Process Management representative for additional information.
  • Page 131 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Table A-10. Rosemount 3051SFP Integral Orifice Flowmeter Ordering Information ★ The Standard offering represents the most common models and options. These options should be selected for best delivery. __The Expanded offering is subject to additional delivery lead time.
  • Page 132 Appendix A: Specifications and reference data Reference Manual May 2013 00809-0200-4802, Rev BA Table A-10. Rosemount 3051SFP Integral Orifice Flowmeter Ordering Information ★ The Standard offering represents the most common models and options. These options should be selected for best delivery. __The Expanded offering is subject to additional delivery lead time.
  • Page 133 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Table A-10. Rosemount 3051SFP Integral Orifice Flowmeter Ordering Information ★ The Standard offering represents the most common models and options. These options should be selected for best delivery. __The Expanded offering is subject to additional delivery lead time.
  • Page 134 Appendix A: Specifications and reference data Reference Manual May 2013 00809-0200-4802, Rev BA Table A-10. Rosemount 3051SFP Integral Orifice Flowmeter Ordering Information ★ The Standard offering represents the most common models and options. These options should be selected for best delivery. __The Expanded offering is subject to additional delivery lead time.
  • Page 135 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Table A-10. Rosemount 3051SFP Integral Orifice Flowmeter Ordering Information ★ The Standard offering represents the most common models and options. These options should be selected for best delivery. __The Expanded offering is subject to additional delivery lead time.
  • Page 136 Appendix A: Specifications and reference data Reference Manual May 2013 00809-0200-4802, Rev BA Table A-10. Rosemount 3051SFP Integral Orifice Flowmeter Ordering Information ★ The Standard offering represents the most common models and options. These options should be selected for best delivery. __The Expanded offering is subject to additional delivery lead time.
  • Page 137 (10) Available with output code A only. Available approvals are FM Intrinsically Safe, Division 2 (option code I5), ATEX Intrinsic Safety (option code I1), or IECEx Intrinsic Safety (option code I7). Contact an Emerson Process Management representative for additional information.
  • Page 138 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Table A-11. Rosemount 3051S Liquid Level Transmitter ★ The Standard offering represents the most common models and options. These options should be selected for best delivery. __The Expanded offering is subject to additional delivery lead time. Model Transmitter Type 3051S...
  • Page 139 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 ★ Junction Box housing Aluminum –14 NPT ★ Junction Box housing Aluminum M20 x 1.5 ★ Junction Box housing with output Aluminum –14 NPT for remote interface ★...
  • Page 140 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Seal Fill Fluid (High Side) Temperature Limits (Ambient Temperature of 70° F (21° Standard Standard ★ Syltherm XLT -102 to 293 °F (-75 to 145 °C) ★ Silicone 704 32 to 401 °F (0 to 205 °C) ★...
  • Page 141 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Lower Housing Material for FF, Extension Length for EF (High Side) Flush Flanged Seal Extended Flanged Seal Standard Standard ★ None — ★ — 2-in. (50 mm) ★...
  • Page 142 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Other Options (Include with selected model number) Diaphragm Thickness Expanded 0.006-in. (150 μm) available with 316L SST and Alloy C-276 Flushing Plug, Vent/Drain Valve Standard Standard ★ Alloy C-276 plug(s) for flushing connection(s) ★...
  • Page 143 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 Hardware Adjustments Standard Standard (11)(12) ★ Hardware adjustments (zero, span, alarm, security) Flange Adapter Standard Standard ★ -14 NPT flange adapter Expanded SST flange adapter Custody Transfer Standard Standard (13)
  • Page 144 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 ★ CSA FISCO Intrinsically Safe (F fieldbus protocol only) OUNDATION ★ IECEx FISCO Intrinsic Safety (F fieldbus protocol only) OUNDATION ★ ATEX Flameproof, Intrinsic Safety, Type n, Dust ★...
  • Page 145 (12) Not available with housing style codes 00, 2E, 2F, 2G, 2M, 5A, 5J, or 7J. (13) Requires PlantWeb housing and Hardware Adjustments option code D1. Limited availability depending on transmitter type and range. Contact an Emerson Process Management representative for additional information.
  • Page 146 Reference Manual Appendix A: Specifications and reference data 00809-0200-4802, Rev BA May 2013 (21) Not available with output code F or X. Not available with housing code 7J. Not available with option code DA1. (22) Not available with Housing code 00, 5A, 5J, or 7J. (23) The T1 option is not needed with FISCO Product Certifications;...

  • Page 147: Wireless Certifications

    RF spectrum. Nearly every country requires this type of product certification. Emerson is working with governmental agencies around the world to supply fully compliant products and remove the risk of violating country directives or laws governing wireless device usage.
  • Page 148 May 2013 European directive information The EC declaration of conformity for all applicable European directives for this product can be found at www.rosemount.com. A hard copy may be obtained by contacting an Emerson Process Management representative. ATEX directive (94/9/EC) Emerson Process Management complies with the ATEX Directive.
  • Page 149 Reference Manual Appendix B: Product Certifications 00809-0200-4802, Rev BA May 2013 B.1.5 Hazardous locations certifications North American Certifications Factory Mutual (FM) Approvals FM Intrinsically Safe, Non-Incendive, and Dust Ignition-proof. Intrinsically Safe for Class I/II/III, Division 1, Groups A, B, C, D, E, F, and G. Zone Marking: Class I, Zone 0, AEx ia llC Temperature Codes T4 (T = -50 to 70°...
  • Page 150 Reference Manual Appendix B: Product Certifications 00809-0200-4802, Rev BA May 2013 IECEx certifications IECEx Intrinsic Safety Certificate No.: IECEx BAS 04.0017X Ex ia IIC T4 (Ta = -60 °C to 70 °C) For use with Rosemount SmartPower options 00753-9220-0001 only. IP66 Special conditions for safe use (x) The surface resistivity of the antenna is greater than one gigaohm.

  • Page 151: Safety Messages

    To maintain wireless performance and avoid non-compliance with spectrum regulations, do not change the length of cable or the antenna type. If the supplied remote mount antenna kit is not installed per these instructions, Emerson Process Management is not responsible for wireless performance or non-compliance with spectrum regulations.

  • Page 152: Functional Specifications

    Reference Manual Appendix C: High Gain Remote Antenna Option 00809-0200-4802, Rev BA May 2013 Functional specifications Output WirelessHART 2.4 GHz DSSS (Direct Sequence Spread Spectrum). Radio Frequency Power Output from Antenna: High Gain Remote (WN option) antenna: Maximum of 40 mW (16 dBm) EIRP ...

  • Page 153: Installation Considerations

    Reference Manual Appendix C: High Gain Remote Antenna Option 00809-0200-4802, Rev BA May 2013 Vibration 3g Max vibration Installation considerations Antenna mounting Mount antenna vertically (±5°) Antenna height Mount antenna 14 feet (4.3 meters) above infrastructure with clear line of sight. Coaxial Cable Ensure that coaxial cable is securely affixed to the mast to avoid excessive cable movement.

  • Page 154: Dimensional Drawings

    Reference Manual Appendix C: High Gain Remote Antenna Option 00809-0200-4802, Rev BA May 2013 Dimensional drawings Device Connection & RF Lightning Arrestor High Gain Remote Antenna Option...

  • Page 155: Installation Steps

    Reference Manual Appendix C: High Gain Remote Antenna Option 00809-0200-4802, Rev BA May 2013 Installation steps Mount the transmitter following best practice mounting procedures as outlined in the Quick Installation Guide and Product Manual. Connect the RF Lightning protector to the device and tighten. RF Lightning Protector Connect antenna to mounting bracket and tighten nut carefully.
  • Page 156 Reference Manual Appendix C: High Gain Remote Antenna Option 00809-0200-4802, Rev BA May 2013 Unwind coaxial cable and connect the cable to both the antenna and the lightning protector connected to the transmitter. Leaving one loop minimum for a drip loop. Ensure the drip loop is lower than the device allowing water to flow away from the device.
  • Page 157 Reference Manual Appendix C: High Gain Remote Antenna Option 00809-0200-4802, Rev BA May 2013 Attach u-bolts to mounting bracket in correct orientation ensuring that antenna will be positioned in a vertical position. Tighten u-bolts to mast and ensure that antenna is pointed in a vertical direction. High Gain Remote Antenna Option...
  • Page 158 Reference Manual Appendix C: High Gain Remote Antenna Option 00809-0200-4802, Rev BA May 2013 High Gain Remote Antenna Option...
  • Page 159 Reference Manual Appendix C: Field Communicator Menu Trees 00809-0200-4802, Rev BA May 2013 Appendix D Field Communicator Menu Trees and Fast Keys Field Communicator menu trees ......... . page 151 Field Communicator menu trees Figure D-1.
  • Page 160 Reference Manual Appendix C: Field Communicator Menu Trees 00809-0200-4802, Rev BA May 2013 Figure D-2. Rosemount 3051S Wireless Field Communicator menu tree: Configure Guided Setup 1 Basic Setup 2 Zero Sensor Trim 3 Join Device to Network 4 Configure Update Rate 5 Configure Device Display 6 Configure Process Alerts 7 Scaled Variable...
  • Page 161 Reference Manual Appendix C: Field Communicator Menu Trees 00809-0200-4802, Rev BA May 2013 Figure D-3. Rosemount 3051S Wireless Field Communicator menu tree: Manual Setup Broadcast Info Set Range Points 1 Configure Update Rate 1 PV Value 2 Message 1 2 PV Upper Range Value 3 Message 2 3 PV Lower Range Value Wireless Setup...
  • Page 162 Reference Manual Appendix C: Field Communicator Menu Trees 00809-0200-4802, Rev BA May 2013 Figure D-4. Rosemount 3051S Wireless Field Communicator menu tree: Manual Setup Active Alert Name Active Alerts 1 Alert Description 1 Refresh Alerts 2 Recommended Actions 2 Active Alert Name #1 3 Active Alert Image #1 4 Active Alert Name #2 5 Active Alert Image #2...
  • Page 163 Reference Manual Index 00809-0200-4802, Rev BA May 2013 Index ......54 ....30 Analog output trim Environmental considerations .
  • Page 164 Reference Manual Index 00809-0200-4802, Rev BA May 2013 Mounting Terminal block diagrams ......40 Bolt installation HARTprotocol .
  • Page 166 May 2013 Standard Terms and Conditions of Sale can be found at www.rosemount.com/terms_of_sale The Emerson logo is a trademark and service mark of Emerson Electric Co. Rosemount. the Rosemount logotype, and SMART FAMILY are registered trademarks of Rosemount Inc. Coplanar is a trademark of Rosemount Inc.

This manual is also suitable for:

Rosemount 3051shpRosemount 3051s

Table of Contents