Table of Contents
Advertisement
PCM Down Sampling
If your amplifier is not capable of reproducing a 96kHz
signal, PCM downsampling should be set to on.
1 Open "MENU"
Press the MENU button while the DVD is in Stop
mode.
2 Select "DVD"
Use the UP/DOWN buttons to highlight "DVD "
then press the ENTER button.
3 Select "Audio"
Highlight "Audio", then press the ENTER button.
4 Set "PCM Down Sampling"
Highlight "PCM Down Sampling", then press the
RIGHT button to select one of the following options:
• On – When a 96K audio disc is played, 96K will
be downsampled to 48K and outputted.
• Off – When a 96K disc is played, 96K will be
outputted.
On
PCM Down Sampling
: On
Off
TV Aspect Ratio
Set the aspect ratio (length x width) of your TV screen
so the DVD player will display movies at the
appropriate size for your television. Choose from
standard, letterbox, or widescreen format.
1 Open "MENU"
Press the MENU button while the DVD is in Stop
mode.
2 Select "DVD"
Use the UP/DOWN buttons to highlight "DVD"
then press the ENTER button.
3 Select "Display"
Highlight "Display", then press the ENTER button.
4 Set "TV Aspect"
Highlight "TV Aspect" then press the RIGHT button
to select one of the following options:
• Widescreen - This method allows you to view the
full 16:9 picture on a widescreen television.
• Letterbox - This method displays the full width of
the widescreen movie on a standard 4:3
television. As a result, black bars will appear at
the top and bottom of the screen.
• Pan-Scan - The familiar way of watching DVD and
VHS movies, this method selectively crops (by
panning and scanning to keep the most important
part of the picture visible) wide screen movies to
fit a standard 4:3 television screen.
Display Setup
ENG-18
Black Level
The Black Level feature adjusts the reference level of
black in the video signal to one of two choices:
• Off - Standard NTSC black level. Yields
consistent contrast through all sources.
• On - Enhanced black level, for increased contrast
during DVD playback.
1 Open "MENU"
Press the MENU button while the DVD is in Stop
mode.
2 Select "DVD"
Use the UP/DOWN buttons to highlight "DVD "
then press the ENTER button.
3 Select "Display"
Highlight "Display", then press the ENTER button.
4 Set "Black Level"
Highlight "Black Level," then press the RIGHT
button to select one of the following options:
• On – This will enhance the Black Level for
increased brightness/contrast when
viewing DVDs.
• Off – This is the Standard NTSC reference Black
Level for consistent brightness/contrast
across all sources.
Display Setup
On
On
Off
Alt Video Out
The "Alt Video Out" option must be set in the on-
screen menu if you have connected your DVD-VCR to a
TV using the S-VIDEO OUT or COMPONENT VIDEO
OUT jacks.
• Use the S-Video or Component Video connection
method only for the DVD player. The tuner and
VCR can still be viewed through the RF or line
outputs.
1 Open "MENU"
Press the MENU button while the DVD is in Stop
mode.
2 Select "DVD"
Use the UP/DOWN buttons to highlight "DVD,"
then press the ENTER button.
3 Select "Display"
Highlight "Display", then press the ENTER button.
4 Set "Alt Video Out"
Highlight "Alt Video Out," then press the RIGHT
button to select one of the following options:
• S-Video - Select this if you are using the S-Video
OUT jack on the rear panel to connect to a TV.
• Component - Select this if you are using the
COMPONENT VIDEO OUT jacks on the rear
panel to connect to a Progressive(480p) or
Interlaced (480i) TV.
• See your TV owner's manual to determine what
type of TV you have.
- Interlace : Interlaced Scan mode will work.
- Progressive : Progressive Scan mode will work,
and Video and S-Video will not work.
ENG-19
Advertisement
Table of Contents
