Attention: This service manual is only for service personnel to take reference with. Before servicing please read the following points carefully. Safety instructions 1. Instructions Be sure to switch off the power supply before replacing or welding any components inserting/plugging in connection wire Anti static measures to be taken (throughout the entire production process!): a) Do not touch here and there by hand at will;...
Page 4
would be unable to work and no way to get it repaired. 2.11 Special care must be taken in transporting or handling it. Exquisite shock vibration may lead to breakage of screen glass or damage to driving circuit. Therefore it must be packed in a strong case before the transportation or handling.
Alignment instruction 1 Alignment equipment PM5518 (video signal generator) K-7253 (VGA signal generator) CA210 (white balancer) 2 Alignment flow-chart The alignment flow-chart is shown as fig-1 Check DDC, HDCP KEY and CPU Factory initialization setup IF channel voltage of TV and AGC voltage adjustment Support format of VGA pre-set Adjustment for sub-brightness and white balance of VGA/HDMI (color temperature 6500k, 9300k and 12000k)
Page 6
Table1 sub-menu adjustment Items Range Introduce PW on LOGO ON/OFF Display 5s LOGO of turn on the TV NO Sig LOGO ON/OFF If display LOGO in no signal Black Screen BLUE/BLACK If display blue screen and white noise wave in no signal, setting “BLUE”...
Page 7
f. Input PROG852(640*480/75Hz) and the eighth level gray-scale of PATTERN signal of VG-849 to HDMI, repeatedly the b-e course. In the HDMI channel, preset value of offset_R, offset_G and offset_B to 15, preset value of gain_R, gain_G and gain_B to 25. 3.4 Adjustment for sub-brightness and white balance of YPbPr channel a.
Item Setting Item Setting Item Setting Picture mode NATURE OSD language English Sound mode NORMAL HALFTONE STEREO WEAK DURATION VGA/HDMI NORMAL SCREEN FULL MAG.C ANTENNA CATV Working principle analysis RF signal from the antenna to tuner, via high frequency amplifier and mix frequency to obtain IF signal, and then via pre-IF amplifier in V104, then it send to processed IF filter of SAW (Z103), obtain more idea IF speciality, it processed to IF amplifier, phase locked logic VCO and sync detection of N101 (M52760E) in the TV board to obtain VIDEO;...
Trouble shooting 1. Fault clearance Before servicing please check to find the possible causes of the troubles according to the table below. 1.1 Antenna (signal): Picture is out of focus or jumping Bad status in signal receiving Poor signal Check if there are failures with the electrical connector or the antenna.
Page 16
signal types. Picture too bright and there is Check if the contrast setting is too high. distortion in the brightest area Possibly the output quality of DVD broadcaster is set too high. It maybe also due to improper terminal connection of the video frequency signal in a certain position of the system.
Page 17
2. Identification criteria for the bright spot and dark spot of the LCD screen Quantity allowed Distance between two spots Category Criteria 15" 20" 22" 30" 40" 15" 20" 22" 30" 40" One single ≤5 ≤2 ≤5 ≤2 ≤3 spot Bright ≥15mm spot...
Page 18
3.Troubleshooting guide 3.1 No raster Turn-on power supply, check if the red indicator is light in the STANDBY? Check if PIN8(5V) of CPU Press POWER button in the board is normal? unit button or sensor control, then check the indicator. blue Check if the PIN12 of X503 in Check STANDBY circuit of...
Page 19
3.2 Raster, but no picture Check if the unit button Does display sensor control menu in screen when operation? press menu button? Check channels have signal? HDMI/VGA/YPRP Enter factory-menu, Which is no initialization EEPROM, signal Replacing then turn off the TV, channels CPU board turn on again, display...
Page 20
3.3 no sound Check if PIN15, PIN30 Check PIN26 and PIN38 voltage of PIN27 output wave of Replacing N401 N401 is normal? N801 Check power supply Check PIN13 output wave of N101 Replacing N801 Check PIN5 wave of Replacing N101 Z102 Check PIN11 wave of TUNER1...
Page 36
PART LIST OF EXPLODED VIEW DESCRIPTION PART# Back cover 808-10756-AF0 Left side cover 808-10757-AF0 Right side cover 808-10758-AF0 Button board assy 667-L27U6-05 Rear cabinet assy 611-G05RPJAF1 Screw 851-23010-14 Wall mount bracket (middle) 870-10133-00B Wall mount bracket (horizontal) 870-10218-00B Wall mount bracket (vertical) 870-10219-00 Panel trans-connecting support 803-10245-00...