Asus ROG Strix X299-E Gaming Manual
  1. Manuals
  2. Brands
  3. Asus Manuals
  4. Motherboard
  5. ROG Strix X299-E Gaming
  6. Manual
Asus ROG Strix X299-E Gaming Manual

Asus ROG Strix X299-E Gaming Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

ROG STRIX
X299-E
GAMING

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ROG Strix X299-E Gaming and is the answer not in the manual?

Questions and answers

Related Manuals for Asus ROG Strix X299-E Gaming

Summary of Contents for Asus ROG Strix X299-E Gaming

  • Page 1 ROG STRIX X299-E GAMING...
  • Page 2 Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing.

  • Page 3: Table Of Contents

    Contents Safety information ...................... vi About this guide ......................vii ROG STRIX X299-E GAMING specifications summary ........... ix Package contents ..................... xiv Installation tools and components ................xv Chapter 1: Product Introduction Motherboard overview ................1-1 1.1.1 Before you proceed ..............1-1 1.1.2...
  • Page 4 3.6.12 PCH-FW Configuration ............. 3-18 Monitor menu ................... 3-19 Boot menu ....................3-19 Tool menu ....................3-21 3.9.1 ASUS EZ Flash 3 Utility ............3-21 3.9.2 Secure Erase ................3-22 3.9.3 ASUS Overclocking Profile ............3-23 3.9.4 ASUS SPD Information ............. 3-23 3.9.5...
  • Page 5 Virtual Raid on CPU in UEFI BIOS ........4-6 ® 4.1.5 Intel Rapid Storage Technology Option ROM utility ....4-12 ® Creating a RAID driver disk ..............4-16 4.2.1 Creating a RAID driver disk in Windows ......... 4-16 ® Appendix Notices ........................A-1 ASUS contact information ..................A-7...

  • Page 6: Safety Information

    Safety information Electrical safety • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.

  • Page 7: About This Guide

    Refer to the following sources for additional information and for product and software updates. ASUS website The ASUS website (www.asus.com) provides updated information on ASUS hardware and software products. Optional documentation Your product package may include optional documentation, such as warranty flyers that may have been added by your dealer.
  • Page 8 Conventions used in this guide To ensure that you perform certain tasks properly, take note of the following symbols used throughout this manual. DANGER/WARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task.

  • Page 9: Rog Strix X299-E Gaming Specifications Summary

    ROG STRIX X299-E GAMING specifications summary Intel Core™ X-Series Processor Family on LGA 2066 socket ® Supports 14nm CPU Supports Intel Turbo Boost Max Technology 3.0* ® The support of these features depends on the CPU types. Refer to www.asus.com for Intel CPU support list.
  • Page 10 ROG STRIX X299-E GAMING specifications summary Intel I219-V Gigabit LAN- Dual interconnect between the integrated ® Media Access Controller (MAC) and physical layer (PHY) Anti-surge LANGuard ROG GameFirst technology Wi-Fi 802.11 a/b/g/n/ac supports dual frequency band 2.4/5 GHz with MU-MIMO support Wireless &...
  • Page 11 ROG STRIX X299-E GAMING specifications summary Performance Optimization 5-Way Optimization - Whole system optimization with a single click! Perfectly consolidates better CPU performance, power saving, digital power control, system cooling and app usages. Digi+VRM - EPU - Auto Tuning Fan Xpert 4 featuring Fan Auto Tuning function and multiple...
  • Page 12 2 x USB3.1 Gen 2 ports (1 x Type-A [red] and 1 x Type-C™ ports at back panel) Back I/O Ports 1 x Anti-surge LAN (RJ45) port 1 x ASUS Wi-Fi module (Wi-Fi 802.11 a/b/g/n/ac and Bluetooth v4.2) 5 x Audio jacks 1 x Optical S/PDIF out 1 x USB 3.1 Gen2 front panel connector...
  • Page 13 ACPI 6.0, Multi-language BIOS, ASUS EZ Flash 3, CrashFree BIOS 3, F11 EZ Tuning Wizard, F6 Qfan Control, F3 My Favorites, BIOS Features Last Modified log, F12 PrintScreen, and ASUS DRAM SPD (Serial Presence Detect) memory information. Manageability WfM2.0, DMI3.0, WOL by PME, PXE...

  • Page 14: Package Contents

    1 x RGB LED extension cable 1 x Addressable LED extension cable 1 x Thermal sensor cable 1 x I/O Shield 1 x ASUS 2x2 dual band Wi-Fi moving antennas (Wi-Fi 802.11a/b/g/n/ac compliant) 1 x ROG cable label 1 x Q-Connector Kit...

  • Page 15: Installation Tools And Components

    Installation tools and components Intel LGA2066 CPU ® Intel LGA2066 compatible CPU Fan ® PC chassis SATA hard disk drive Philips (cross) screwdriver 1 bag of screws DIMM Power supply unit SATA optical disc drive (optional) Graphics card The tools and components in the table above are not included in the motherboard package.

  • Page 17: Chapter 1: Product Introduction

    Unplug the power cord from the wall socket before touching any component. • Before handling components, use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, to avoid damaging them due to static electricity. • Hold components by the edges to avoid touching the ICs on them. • Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that came with the component. • Before you install or remove any component, ensure that the ATX power supply is switched off or the power cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard, peripherals, or components. ROG STRIX X299-E GAMING...

  • Page 18: Motherboard Layout

    1.1.2 Motherboard layout Refer to 1.1.9 Internal connectors and 2.3.1 Rear I/O connection for more information about rear panel connectors and internal connectors. Chapter 1: Product Introduction...
  • Page 19 1-18 ® SATA6G_34, SATA6G_56, SATA6G_78) 11. VROC_HW_KEY connector (4-pin VROC_HW_KEY) 1-27 12. Clear RTC RAM jumper (2-pin CLRTC) 1-11 13. CPU Over Voltage jumper (3-pin CPU_OV) 1-12 14. System panel connector (20-3 pin PANEL) 1-24 15. 3D Mount 1-12 16. Addressable header (4-1 pin ADD_HEADER) 1-26 17. USB 2.0 connectors (10-1 pin USB910) 1-21 18. Power-on button 1-10 19. Q-Code LED 1-13 20. Serial port connector (10-1 pin COM) 1-19 21. Front panel audio connector (10-1 pin AAFP) 1-27 ROG STRIX X299-E GAMING...

  • Page 20: Central Processing Unit (Cpu)

    1.1.3 Central Processing Unit (CPU) The motherboard comes with a surface mount LGA2066 socket designed for Intel Core™ ® X-Series Processor Family. • Ensure that all power cables are unplugged before installing the CPU. • Upon purchase of the motherboard, ensure that the PnP cap is on the socket and the socket contacts are not bent. Contact your retailer immediately if the PnP cap is missing, or if you see any damage to the PnP cap/socket contacts/motherboard components. ASUS will shoulder the cost of repair only if the damage is shipment/ transit-related. • Keep the cap after installing the motherboard. ASUS will process Return Merchandise Authorization (RMA) requests only if the motherboard comes with the cap on the LGA2066 socket. • The product warranty does not cover damage to the socket contacts resulting from incorrect CPU installation/removal, or misplacement/loss/incorrect removal of the PnP cap. Chapter 1: Product Introduction...

  • Page 21: System Memory

    1.1.4 System memory The motherboard comes with eight (8) DDR4 (Double Data Rate 4) Dual Inline Memory Modules (DIMM) slots. A DDR4 module is notched differently from a DDR, DDR2, or DDR3 module. DO NOT install a DDR, DDR2, or DDR3 memory module to the DDR4 slot. Ensure to install at least one of the memory modules into the A1*/B1*/C1*/D1* slot under X-Series (6-core above) Processors. Recommended memory configurations Intel Core™ X-Series (6-core above) Processors ® ROG STRIX X299-E GAMING...
  • Page 22 DIMM sockets. • For Intel Core™ X-series (4-core) Processors, you may install varying memory sizes ® in Channel C and Channel D. The system maps the total size of the lower-sized channel for the dual-channel configuration. Any excess memory from the higher-sized channel is then mapped for single-channel operation. • For Intel Core™ X-series (6-core above) Processors, you may install varying memory ® sizes in Channel A, Channel B, Channel C, and Channel D. The system maps the total size of the lower-sized channel for the quad-channel configuration. Any excess memory from the higher-sized channel is then mapped for single-channel operation. • The default memory operation frequency is dependent on its Serial Presence Detect (SPD), which is the standard way of accessing information from a memory module. Under the default state, some memory modules for overclocking may operate at a lower frequency than the vendor-marked value. • For system stability, use a more efficient memory cooling system to support a full memory load (8 DIMMs) or overclocking condition. • Always install the DIMMS with the same CAS Latency. For an optimum compatibility, we recommend that you install memory modules of the same version or data code (D/C) from the same vendor. Check with the vendor to get the correct memory modules. • Visit the ASUS website for the latest QVL. Chapter 1: Product Introduction...

  • Page 23: Expansion Slots

    1.1.5 Expansion slots Unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components. ROG STRIX X299-E GAMING...
  • Page 24 44-LANE CPU PCI Express 3.0 operating mode VGA configuration PCIEX16/X8_1 PCIEX16/X8_2 PCIEX8/X1_3 x16 Single VGA/PCIe card (single VGA recommended) Dual VGA/PCIe cards Triple VGA/PCIe cards 28-LANE CPU PCI Express 3.0 operating mode VGA configuration PCIEX16/X8_1 PCIEX16/X8_2 PCIEX8/X1_3 x16 Single VGA/PCIe card (single VGA recommended) Dual VGA/PCIe cards Triple VGA/PCIe cards 16-LANE CPU PCI Express 3.0 operating mode VGA configuration PCIEX16/X8_1 PCIEX16/X8_2...
  • Page 25 • We recommend that you provide sufficient power when running CrossFireX™ or SLI ® mode. • Connect a chassis fan to the motherboard connector labeled CHA_FAN1-2 when using multiple graphics cards for better thermal environment. ROG STRIX X299-E GAMING...

  • Page 26: Onboard Buttons And Switches

    1.1.6 Onboard buttons and switches Onboard buttons and switches allow you to fine-tune performance when working on a bare or open-case system. This is ideal for overclockers and gamers who continually change settings to enhance system performance. Power-on button The motherboard comes with a power-on button that allows you to power up or wake up the system. Chapter 1: Product Introduction 1-10...

  • Page 27: Jumpers And Holes

    Plug the power cord and turn ON the computer. Hold down the <Delete> key during the boot process and enter BIOS setup to re-enter data. Except when clearing the RTC RAM, never remove the cap on CLRTC jumper default position. Removing the cap will cause system boot failure! • If the steps above do not help, remove the onboard battery and move the jumper again to clear the CMOS RTC RAM data. After the CMOS clearance, reinstall the battery. • You do not need to clear the RTC when the system hangs due to overclocking. For system failure due to overclocking, use the C.P.R. (CPU Parameter Recall) feature. Shut down and reboot the system so the BIOS can automatically reset parameter settings to default values. • Due to the chipset behavior, AC power off is required to enable C.P.R. function. You must turn off and on the power supply or unplug and plug the power cord before rebooting the system. ROG STRIX X299-E GAMING 1-11...
  • Page 28 CPU Over Voltage jumper (3-pin CPU_OV) The CPU Over Voltage jumper allows you to set a higher CPU voltage for a flexible overclocking system, depending on the type of the installed CPU. To gain more CPU voltage setting, insert the jumper to pins 2-3. To go back to its default CPU voltage setting, insert the jumper to pins 1-2. 3D Mount Secure 3D printed parts to these 3D Mount holes for a personalized motherboard. • Download 3D source files at http://www.asus.com. • Use the bundled 3D Mount screws to install the 3D printed parts. Chapter 1: Product Introduction 1-12...

  • Page 29: Onboard Leds

    1.1.8 Onboard LEDs POST State LEDs The POST State LEDs provide the status of these key components during POST (Power-On Self-Test): CPU, memory modules, VGA card, and hard disk drives. If an error is found, the critical component’s LED stays lit up until the problem is solved. Q-Code LED The Q-Code LED design provides you with a 2-digit error code that displays the system status. Refer to the Q-Code table below for details. ROG STRIX X299-E GAMING 1-13...
  • Page 30 Q-Code table Code Description Not used Power on. Reset type detection (soft/hard). AP initialization before microcode loading System Agent initialization before microcode loading PCH initialization before microcode loading Microcode loading AP initialization after microcode loading System Agent initialization after microcode loading PCH initialization after microcode loading Cache initialization Reserved for future AMI SEC error codes 0C – 0D Microcode not found Microcode not loaded PEI Core is started Pre-memory CPU initialization is started 11 – 14 Pre-memory System Agent initialization is started 15 – 18 19 – 1C Pre-memory PCH initialization is started Memory initialization 2B – 2F Reserved for ASL (see ASL Status Codes section below) Memory Installed CPU post-memory initialization 32 –...
  • Page 31 Reserved for future AMI error codes EC – EF Recovery condition triggered by firmware (Auto recovery) Recovery condition triggered by user (Forced recovery) Recovery process started Recovery firmware image is found Recovery firmware image is loaded Reserved for future AMI progress codes F5 – F7 Recovery PPI is not available Recovery capsule is not found Invalid recovery capsule FB – FF Reserved for future AMI error codes DXE Core is started NVRAM initialization Installation of the PCH Runtime Services CPU DXE initialization is started 63 – 67 PCI host bridge initialization System Agent DXE initialization is started System Agent DXE SMM initialization is started System Agent DXE initialization (System Agent module specific) 6B – 6F (continued on the next page) ROG STRIX X299-E GAMING 1-15...
  • Page 32 Q-Code table Code Description PCH DXE initialization is started PCH DXE SMM initialization is started PCH devices initialization PCH DXE Initialization (PCH module specific) 73 – 77 ACPI module initialization CSM initialization Reserved for future AMI DXE codes 7A – 7F Boot Device Selection (BDS) phase is started Driver connecting is started PCI Bus initialization is started PCI Bus Hot Plug Controller Initialization PCI Bus Enumeration PCI Bus Request Resources PCI Bus Assign Resources Console Output devices connect Console input devices connect Super IO Initialization USB initialization is started USB Reset USB Detect USB Enable 9E – 9F Reserved for future AMI codes IDE initialization is started IDE Reset IDE Detect IDE Enable SCSI initialization is started SCSI Reset SCSI Detect SCSI Enable...
  • Page 33 Description Start of Setup Reserved for ASL (see ASL Status Codes section below) Setup Input Wait Reserved for ASL (see ASL Status Codes section below) Ready To Boot event Legacy Boot event Exit Boot Services event Runtime Set Virtual Address MAP Begin Runtime Set Virtual Address MAP End Legacy Option ROM Initialization System Reset USB hot plug PCI bus hot plug Clean-up of NVRAM Configuration Reset (reset of NVRAM settings) B8– BF Reserved for future AMI codes CPU initialization error System Agent initialization error PCH initialization error Some of the Architectural Protocols are not available PCI resource allocation error. Out of Resources No Space for Legacy Option ROM No Console Output Devices are found No Console Input Devices are found Invalid password Error loading Boot Option (LoadImage returned error) Boot Option is failed (StartImage returned error) Flash update is failed Reset protocol is not available ROG STRIX X299-E GAMING 1-17...

  • Page 34: Internal Connectors

    1.1.9 Internal connectors Intel X299 Serial ATA 6Gb/s connectors (7-pin SATA6G_12, SATA6G_34, ® SATA6G_56, SATA6G_78) These connectors connect to Serial ATA 6Gb/s hard disk drives via Serial ATA 6Gb/s signal cables. If you installed Serial ATA hard disk drives, you can create a RAID 0, 1, 5, and 10 configuration with the Intel Rapid Storage Technology through the onboard Intel ® ® X299 chipset. • These connectors are set to [AHCI] by default. If you intend to create a Serial ATA RAID set using these connectors, set the SATA Mode item in the BIOS to [Intel RST Premium With Intel Optane System Acceleration (RAID)]. • Before creating a RAID set, refer to the manual bundled in the motherboard support DVD. Chapter 1: Product Introduction 1-18...
  • Page 35 M.2 Socket 3 These sockets allow you to install M.2 SSD modules. • M.2_1 socket supports PCIe 3.0 x4 and SATA mode M Key design and type 2242 / 2260 / 2280 PCIe and SATA storage devices. • M.2_2 socket supports PCIe 3.0 x4 M Key design and type 2242 / 2260 / 2280 / 22110 PCIe storage devices. • These sockets support IRST (Intel Rapid Storage Technology). ® The M.2 SSD module is purchased separately. Serial port connector (10-1 pin COM) These connectors are for the serial (COM) port. Connect the serial port module cable to one of these connectors, then install the module to a slot opening at the back of the system chassis. ROG STRIX X299-E GAMING 1-19...
  • Page 36 USB 3.1 Gen 2 front panel connector (U31G2_E3) This connector allows you to connect a USB 3.1 Gen 2 module for additional USB 3.1 Gen 2 ports. The latest USB 3.1 Gen 2 connectivity provides data transfer speeds of up to 10 Gbps. USB 3.1 Gen 1 connectors (20-1 pin U31G1_12, U31G1_34) These connectors allow you to connect a USB 3.1 Gen1 module for additional USB 3.1 Gen1 front or rear panel ports. With an installed USB 3.1 Gen1 module, you can enjoy all the benefits of USB 3.1 Gen1 including faster data transfer speeds of up to 5Gb/s, faster charging time for USB-chargeable devices, optimized power efficiency, and backward compatibility with USB 2.0. The USB 3.1 Gen1 module is purchased separately. • Ensure to install the related driver to fully use the USB 3.1 Gen 1 ports under Windows ® • The plugged USB 3.1 Gen 1 device may run on xHCI or EHCI mode depending on theoperating system’s setting. Chapter 1: Product Introduction 1-20...
  • Page 37 USB 2.0 connectors (10-1 pin USB910) These connectors are for USB 2.0 ports. Connect the USB module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2.0 specification that supports up to 480Mb/s connection speed. DO NOT connect a 1394 cable to the USB connectors. Doing so will damage the motherboard! The USB 2.0 module is purchased separately. Thermal Sensor connector (2-pin T_SENSOR) This connector is for the thermistor cable that monitors the temperature of the devices and the critical components inside the motherboard. Connect the thermistor cable and place the sensor on the device or the motherboard’s component to detect its temperature. ROG STRIX X299-E GAMING 1-21...
  • Page 38 CPU, CPU optional, M.2, water pump, AIO, extension, and chassis fan connectors (4-pin CPU_FAN; 4-pin CPU_OPT; 4-pin M.2_FAN; 4-pin W_PUMP+; 4-pin AIO_PUMP; 5-pin EXT_FAN; 4-pin CHA_FAN1-2) Connect the fan cables to the fan connectors on the motherboard, ensuring that the black wire of each cable matches the ground pin of the connector. • DO NOT forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components. These are not jumpers! Do not place jumper caps on the fan connectors!
  • Page 39 ATX power connectors (24-pin EATXPWR; 8-pin EATX12V_1; 4-pin EATX12V_2) These connectors are for ATX power supply plugs. The power supply plugs are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. • DO NOT connect the 4-pin power plug only, the motherboard may overheat under heavy usage. • Ensure to connect the 8-pin power plug, or connect both the 8-pin and 4-pin power plugs. A red LED located to the right of the 8-pin power plug will light up if the 8-pin power plug is not connected. • For a fully configured system, we recommend that you use a power supply unit (PSU) that complies with ATX 12V Specification 2.0 (or later version) and provides a minimum power of 350W. • We recommend that you use a PSU with a higher power output when configuring a system with more power-consuming devices. The system may become unstable or may not boot up if the power is inadequate. • If you want to use two or more high-end PCI Express x16 cards, use a PSU with 1000W power or above to ensure the system stability. ROG STRIX X299-E GAMING 1-23...
  • Page 40 System panel connector (20-3 pin PANEL) This connector supports several chassis-mounted functions. • System power LED (2-pin or 3-1 pin PLED) The 2-pin or 3-1 pin connector is for the system power LED. Connect the chassis power LED cable to this connector. The system power LED lights up when you turn on the system power, and blinks when the system is in sleep mode. • Hard disk drive activity LED (2-pin HDD_LED) This 2-pin connector is for the HDD Activity LED. Connect the HDD Activity LED cable to this connector. The HDD LED lights up or flashes when data is read from or written to the HDD. • System warning speaker (4-pin SPEAKER) This 4-pin connector is for the chassis-mounted system warning speaker. The speaker allows you to hear system beeps and warnings. • ATX power button/soft-off button (2-pin PWRSW) This connector is for the system power button. Pressing the power button turns the system on or puts the system in sleep or soft-off mode depending on the operating...
  • Page 41 RGB header (4-pin RGB_HEADER1, RGB_HEADER2) These connectors are for RGB LED strips. • The RGB header supports 5050 multi-color LED strips (+12V/G/R/B), with a maximum power rating of 3A (12V), and no longer than 3 m. • Ensure that the RGB LED extension cable and the RGB LED strip is connected in the correct orientation, and the +12V connector is aligned with the +12V header on the motherboard. Before you install or remove any component, ensure that the ATX power supply is switched off or the power cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard, peripherals, or components. • Actual lighting and color will vary with LED strip. • The lighting effects may be customized with the help of AURA software. • If your LED strip does not light up, check if the RGB LED extension cable and the RGB LED strip is connected in the correct orientation, and the 12V connector is aligned with the 12V header on the motherboard. • The LED strip will only light up when the system is operating. • The LED strips are purchased separately. ROG STRIX X299-E GAMING 1-25...
  • Page 42 Addressable header (4-1 pin ADD_HEADER) This connector is for individually addressable RGB WS2812B LED strips with embedded WS2811 LED driver ICs. The addressable RGB header supports WS2812B addressable RGB LED strips (5V/Data/ Ground), with a maximum power rating of 3A (5V) and a maximum of 60 LEDs. Before you install or remove any component, ensure that the ATX power supply is switched off or the power cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard, peripherals, or components. • Actual lighting and color will vary with LED strip. • If your LED strip does not light up, check if the addressable RGB LED strip is connected in the correct orientation, and the 5V connector is aligned with the 5V header on the motherboard. • The addressable RGB LED strip will only light up under the operating system. • The addressable RGB LED strip is purchased separately. Chapter 1: Product Introduction 1-26...
  • Page 43 13. VROC_HW_KEY connector (4-pin VROC_HW_KEY) This connector allows you to connect a KEY module to enable CPU RAID functions with Intel CPU RSTe. ® The KEY module is purchased separately. Front panel audio connector (10-1 pin AAFP) This connector is for a chassis-mounted front panel audio I/O module that supports HD Audio. Connect one end of the front panel audio I/O module cable to this connector. We recommend that you connect a high-definition front panel audio module to this connector to avail of the motherboard’s high-definition audio capability. ROG STRIX X299-E GAMING 1-27...
  • Page 44 Chapter 1: Product Introduction 1-28...

  • Page 45: Building Your Pc System

    The diagrams in this section are for references only. The motherboard layout may vary with models, but the installation steps are the same for all models. Install the ASUS Q-Shield to the chassis rear I/O panel. Place the motherboard into the chassis, ensuring that its rear I/O ports are aligned to the chassis’...
  • Page 46 Place nine (9) screws into the holes indicated by circles to secure the motherboard to the chassis. DO NOT overtighten the screws! Doing so can damage the motherboard. Chapter 2: Basic Installation...

  • Page 47: Cpu Installation

    Please note the order in opening/closing the double latch. Follow the instructions printed on the metal sealing hatch or the illustrations shown below in this manual. The plastic cap will pop up automatically once the CPU is in place and the hatch properly sealed down. ROG STRIX X299-E GAMING...
  • Page 48 Triangle mark Triangle mark Chapter 2: Basic Installation...

  • Page 49: Cpu Heatsink And Fan Assembly Installation

    2.1.3 CPU heatsink and fan assembly installation Apply the Thermal Interface Material to the CPU heatsink and CPU before you install the heatsink and fan, if necessary. To install the CPU heatsink and fan assembly: ROG STRIX X299-E GAMING...
  • Page 50 To uninstall the CPU heatsink and fan assembly Chapter 2: Basic Installation...

  • Page 51: Dimm Installation

    2.1.4 DIMM installation Ensure to install at least one of the memory modules into the A1 * /B1 * /C1 * /D1 * slot. To remove a DIMM ROG STRIX X299-E GAMING...

  • Page 52: Atx Power Connection

    2.1.5 ATX Power connection • DO NOT connect the 4-pin power plug only, the motherboard may overheat under heavy usage. • Ensure to connect the 8-pin power plug, or connect both 8-pin and 4-pin power plugs. Chapter 2: Basic Installation...

  • Page 53: Sata Device Connection

    2.1.6 SATA device connection ROG STRIX X299-E GAMING...

  • Page 54: Front I/O Connector

    2.1.7 Front I/O connector To install ASUS Q-Connector To install USB 3.1 Gen 2 connector USB 3.1 Gen 2 This connector will only fit in one orientation. Push the connector until it clicks into place. To install USB 3.1 Gen 1 connector To install USB 2.0 connector USB 3.1 Gen 1...

  • Page 55: Expansion Card Installation

    2.1.8 Expansion Card installation To install PCIe x16 cards To install PCIe x1 cards ROG STRIX X299-E GAMING 2-11...
  • Page 56 To install FAN EXTENSION CARD • The illustrations in this section are for reference only. The motherboard layout may vary with models, but the installation steps are the same for all models. • The FAN Extension card is purchased separately. Chapter 2: Basic Installation 2-12...

  • Page 57: M.2 Installation

    2.1.9 M.2 installation • Please remove the plastic film from the thermal pad before use. • Use the bundled M.2 screws to secure the M.2. ROG STRIX X299-E GAMING 2-13...
  • Page 58 Supported M.2 type varies per motherboard. Use the bundled M.2 screws to secure the M.2. Chapter 2: Basic Installation 2-14...

  • Page 59: Wi-Fi Antenna Installation

    2.1.10 Wi-Fi antenna installation Installing the ASUS 2x2 dual band W-Fi antenna Connect the bundled ASUS 2x2 dual band Wi-Fi antenna connector to the Wi-Fi ports at the back of the chassis. • Ensure that the ASUS 2x2 dual band Wi-Fi antenna is securely installed to the Wi-Fi ports. • Ensure that the antenna is at least 20 cm away from all persons. The illustration above is for reference only. The I/O port layout may vary with models, but the Wi-Fi antenna installation procedure is the same for all models. ROG STRIX X299-E GAMING...

  • Page 60: Bios Update Utility

    BIOS Flashback is not operating properly. This may be caused by improper installation of the USB storage device and filename/file format error. If this scenario happens, please restart the system to turn off the light. • Updating BIOS may have risks. If the BIOS program is damaged during the process and results to the system’s failure to boot up, please contact your local ASUS Service Center. Chapter 2: Basic Installation 2-16...

  • Page 61: Motherboard Rear And Audio Connections

    Please connect your USB 3.1 Gen 1 devices to USB 3.1 Gen 1 ports and your USB 3.1 Gen 2 devices to USB 3.1 Gen 2 ports for faster and better performance for your devices. ROG STRIX X299-E GAMING 2-17...
  • Page 62 * LAN ports LED indications Activity Link LED Speed LED Status Description Status Description ACT/LINK SPEED No link 10 Mbps connection Orange Linked Orange 100 Mbps connection Orange (Blinking) Data activity Green 1 Gbps connection Orange (Blinking Ready to wake up LAN port then steady) from S5 mode You can disable the LAN controllers in BIOS.

  • Page 63: Audio I/O Connections

    2.3.2 Audio I/O connections Audio I/O ports Connect to Headphone and Mic Connect to Stereo Speakers Connect to 2 channel Speakers ROG STRIX X299-E GAMING 2-19...
  • Page 64 Connect to 4 channel Speakers Connect to 6 channel Speakers Connect to 8 Speakers Chapter 2: Basic Installation 2-20...

  • Page 65: Starting Up For The First Time

    Turning off the computer While the system is ON, press the power button for less than four seconds to put the system on sleep mode or soft-off mode, depending on the BIOS setting. Press the power switch for more than four seconds to let the system enter the soft-off mode regardless of the BIOS setting. ROG STRIX X299-E GAMING 2-21...
  • Page 66 Chapter 2: Basic Installation 2-22...

  • Page 67: Chapter 3: Bios Setup

    BIOS Setup Knowing BIOS The new ASUS UEFI BIOS is a Unified Extensible Interface that complies with UEFI architecture, offering a user-friendly interface that goes beyond the traditional keyboard- only BIOS controls to enable a more flexible and convenient mouse input. You can easily navigate the new UEFI BIOS with the same smoothness as your operating system.

  • Page 68: Bios Setup Program

    RTC RAM via the Clear CMOS jumper. • The BIOS setup program does not support the Bluetooth devices. Please visit ASUS website for the detailed BIOS content manual. BIOS menu screen The BIOS Setup program can be used under two modes: EZ Mode and Advanced Mode.

  • Page 69: Ez Mode

    Click to go to Advanced mode Search on the FAQ Loads optimized default settings Click to display boot devices Selects the boot device priority The boot device options vary depending on the devices you installed to the system. ROG STRIX X299-E GAMING...

  • Page 70: Advanced Mode

    3.2.2 Advanced Mode The Advanced Mode provides advanced options for experienced end-users to configure the BIOS settings. The figure below shows an example of the Advanced Mode. Refer to the following sections for the detailed configurations. To switch from EZ Mode to Advanced Mode, click Advanced Mode(F7) or press the <F7> hotkey.
  • Page 71 This button above the menu bar allows you to view and tweak the overclocking settings of your system. It also allows you to change the motherboard’s SATA mode from AHCI to RAID mode. Refer to section 3.2.4 EZ Tuning Wizard for more information. ROG STRIX X299-E GAMING...
  • Page 72 Move your mouse over this button to show a QR code, scan this QR code on your mobile device to connect to the BIOS FAQ web page of the ASUS support website. You can also scan the following QR code: Hot keys This button above the menu bar contains the navigation keys for the BIOS setup program.

  • Page 73: Qfan Control

    Click to activate DC Mode PWM Mode configured Click to apply the fan setting Select a profile to apply to Click to undo Click to go back to main menu your fans the changes Select to manually configure your fans ROG STRIX X299-E GAMING...
  • Page 74 Configuring fans manually Select Manual from the list of profiles to manually configure your fans’ operating speed. Speed points Select to manually configure your fans To configure your fans: Select the fan that you want to configure and to view its current status. Click and drag the speed points to adjust the fans’...

  • Page 75: Ez Tuning Wizard

    Ensure that your HDDs have no existing RAID volumes. • Ensure to connect your HDDs to Intel SATA connectors. ® Select the port that you want to set to [RAID] mode, PCIE or SATA, then click Next. ROG STRIX X299-E GAMING...
  • Page 76 Select the type of storage for your RAID, Easy Backup or Super Speed, then click Next. For Easy Backup, click Next then select from Easy Backup (RAID 1) or Easy Backup (RAID 10). You can only select Easy Backup (RAID 10) if you connect four (4) HDDs. For Super Speed, click Next then select from Super Speed (RAID 0) or Super Speed (RAID 5).

  • Page 77: My Favorites

    My Favorites is your personal space where you can easily save and access your favorite BIOS items. My Favorites comes with several performance, power saving, and fast boot related items by default. You can personalize this screen by adding or removing items. ROG STRIX X299-E GAMING 3-11...
  • Page 78 Adding items to My Favorites To add BIOS items: Press <F3> on your keyboard or click from the BIOS screen to open Setup Tree Map screen. On the Setup Tree Map screen, select the BIOS items that you want to save in My Favorites screen.

  • Page 79: Main Menu

    Use the <+> or <-> to adjust the value. The values range from 40.0 MHz to 650.0 MHz. We recommend you to set the value based on the CPU specification, as high BCLK frequencies may damage the CPU permanently. ROG STRIX X299-E GAMING 3-13...
  • Page 80 ASUS MultiCore Enhancement [Auto] This item allows you to maximize the oveclocking performance optimized by ASUS core ratio settings. [Disabled] This item allows you to set to default core ratio settings. CPU Core Ratio This item allows you to set the CPU core ratios.

  • Page 81: Advanced Menu

    The items in this menu allow you to change the ASPM for PCH and SA PCI Express. 3.6.3 System Agent (SA) Configuration The items in this menu allow you to adjust the Link Speed for PEG Port and Multi-Monitor. ROG STRIX X299-E GAMING 3-15...

  • Page 82: Pch Configuration

    3.6.4 PCH Configuration The items in this menu allow you to adjust the PCH PCI Express speed. PCI Express Configuration This item allows you to configure the PCI Express slots. PCIe Speed This item allows your system to automatically select the PCI Express port speed. Configuration options: [Auto] [Gen1 (2.5 GT/s)] [Gen2] (5 GT/s) [Gen3 (8 GT/s)] 3.6.5 PCH Storage Configuration...

  • Page 83: Cpu Storage Configuration

    This item allows you to turn the RGB LED lighting on or off when the system is in the sleep, hibernate or soft off states. Configuration options: [On] [Off] Intel LAN Controller This item allows you to enable or disable the Intel LAN controllers. Configuration options: [Disabled] [Enabled] ROG STRIX X299-E GAMING 3-17...

  • Page 84: Apm Configuration

    Wi-Fi 802.11ac Controller This item allows you to enable or disable the Intel Wi-Fi 802.11ac controller. Configuration options: [Disabled] [Enabled] Intel LAN Controller This item allows you to enable or disable the Intel(R) LAN controller. Configuration options: [Disabled] [Enabled] 3.6.8 APM Configuration The items in this menu allow you to set system wake and sleep settings.

  • Page 85: Monitor Menu

    Boot Configuration Setup Mode [Advanced Mode] This item allows you to go to Advanced Mode of the BIOS after POST. [EZ Mode] This item allows you to go to EZ Mode of the BIOS after POST. ROG STRIX X299-E GAMING 3-19...
  • Page 86 CSM (Compatibility Support Module) This item allows you to configure the CSM (Compatibility Support Module) items to fully support the various VGA, bootable devices and add-on devices for better compatibility. Launch CSM [Auto] The system automatically detects the bootable devices and the add- on devices.

  • Page 87: Tool Menu

    3.9.1 ASUS EZ Flash 3 Utility This item allows you to run ASUS EZ Flash 3. When you press <Enter>, a confirmation message appears. Use the left/right arrow key to select between [Yes] or [No], then press <Enter> to confirm your choice.

  • Page 88: Secure Erase

    To launch Secure Erase, click Tool > Secure Erase on the Advanced mode menu. Check the ASUS support site for a full list of SSDs tested with Secure Erase. The drive may become unstable if you run Secure Erase on an incompatible SSD.

  • Page 89: Asus Overclocking Profile

    This item displays the information and recommended configuration for the PCIE slots that the graphics card is installed in your system. This feature is only supported on selected ASUS graphics cards. Bus Interface This item allows you to select the bus interface.

  • Page 90: Exit Menu

    3.10 Exit menu The Exit menu items allow you to load the optimal default values for the BIOS items, and save or discard your changes to the BIOS items. You can access the EZ Mode from the Exit menu. Load Optimized Defaults This option allows you to load the default values for each of the parameters on the Setup menus.

  • Page 91: Updating Bios

    ® ASUS EZ Flash 3: Updates the BIOS using a USB flash drive. ASUS CrashFree BIOS 3: Restores the BIOS using the motherboard support DVD or a USB flash drive when the BIOS file fails or gets corrupted. 3.11.1...

  • Page 92: Asus Ez Flash 3

    3.11.2 ASUS EZ Flash 3 ASUS EZ Flash 3 allows you to download and update to the latest BIOS through the Internet without having to use a bootable floppy disk or an OS-based utility. Updating through the Internet varies per region and Internet conditions. Check your local Internet connection before updating through the Internet.
  • Page 93 To update the BIOS by Internet: Enter the Advanced Mode of the BIOS setup program. Go to the Tool menu to select ASUS EZ Flash 3 Utility and press <Enter>. Select by Internet. Press the Left/Right arrow keys to select an Internet connection method, and then press <Enter>.

  • Page 94: Asus Crashfree Bios 3

    The BIOS file in the motherboard support DVD may be older than the BIOS file published on the ASUS official website. If you want to use the newer BIOS file, download the file at https://www.asus.com/support/ and save it to a USB flash drive.

  • Page 95: Raid Support

    With the RAID 10 configuration you get all the benefits of both RAID 0 and RAID 1 configurations. Use four new hard disk drives or use an existing drive and three new drives for this setup. ROG STRIX X299-E GAMING...

  • Page 96: Installing Serial Ata Hard Disks

    4.1.2 Installing Serial ATA hard disks The motherboard supports Serial ATA hard disk drives. For optimal performance, install identical drives of the same model and capacity when creating a disk array. To install the SATA hard disks for a RAID configuration: Install the SATA hard disks into the drive bays.
  • Page 97 When the RAID Level item is selected, press <Enter> to select the RAID level to create, and then press <Enter>. Under Select Disks, press <Enter> and select X for the disks you want to include in the RAID set. ROG STRIX X299-E GAMING...
  • Page 98 When the Strip Size item is selected, press <Enter> to select strip size for the RAID array (for RAID 0, 10 and 5 only), and then press <Enter>. The available strip size values range from 4 KB to 128 KB. The following are typical values: RAID 0: 128 KB RAID 10: 64 KB RAID 5: 64 KB...
  • Page 99 <Enter>. The following screen appears: When the Delete item is selected, press <Enter>, then select Yes to delete the RAID volume and return to the Intel(R) Rapid Storage Technology menu, or select No to cancel. ROG STRIX X299-E GAMING...

  • Page 100: Intel ® Virtual Raid On Cpu In Uefi Bios

    4.1.4 Intel Virtual Raid on CPU in UEFI BIOS ® This feature requires a KEY module to enable CPU RAID functions with Intel CPU RSTe. ® • The KEY module is purchased separately. • Due to chipset behavior, CPU RAID functions with Intel CPU RSTe only supports ®...
  • Page 101 When the Enable RAID spanned over VMD Controllers item is selected, press <Enter> and select X to enable this function. Under Select Disks, press <Enter> and select X for the disks you want to include in the RAID set. ROG STRIX X299-E GAMING...
  • Page 102 When the Strip Size item is selected, press <Enter> to select strip size for the RAID array (for RAID 0, 10 and 5 only), and then press <Enter>. The available strip size values range from 4 KB to 128 KB. The following are typical values: RAID 0: 128 KB RAID 10: 64 KB RAID 5: 64 KB...
  • Page 103 <Enter>. The following screen appears: When the Delete item is selected, press <Enter>, then select Yes to delete the RAID volume and return to the Intel Virtual Raid on CPU menu, or select No to cancel. ® ROG STRIX X299-E GAMING...
  • Page 104 Installing the RAID controller driver during Windows 10 OS installation ® After creating the RAID sets, you are now ready to install an operating system to the independent drives or bootable array. This part provides the instructions on how to install the RAID controller drivers during OS installation.
  • Page 105 When the system finishes loading the RAID driver, replace the motherboard Support DVD with the Windows Server installation disc. Select the drive to install Windows and click Next. Setup then proceeds with the OS installation. Follow screen instructions to continue. ROG STRIX X299-E GAMING 4-11...

  • Page 106: Intel ® Rapid Storage Technology Option Rom Utility

    4.1.5 Intel Rapid Storage Technology Option ROM utility ® To enter the Intel Rapid Storage Technology Option ROM utility: ® Turn on the system. During POST, press <Ctrl> + <I> to display the utility main menu. RAID Volumes: None defined. Physical Devices: Port Device Model...
  • Page 107 Size Status ST3160812AS 9LS0HJA4 149.0GB Non-RAID Disk ST3160812AS 9LS0F4HL 149.0GB Non-RAID Disk ST3160812AS 3LS0JYL8 149.0GB Non-RAID Disk ST3160812AS 9LS0BJ5H 149.0GB Non-RAID Disk Select 2 to 6 to use in creating the volume. [↑↓]-Prev/Next [SPACE]-SelectDisk [ENTER]-Done ROG STRIX X299-E GAMING 4-13...
  • Page 108 Use the up/down arrow key to select a drive, and then press <Space> to select. A small triangle marks the selected drive. Press <Enter> after completing your selection. Use the up/down arrow key to select the strip size for the RAID array (for RAID 0, 10 and 5 only), and then press <Enter>.
  • Page 109 (This does not apply to Recovery volumes) Are you sure you want to delete “Volume0”? (Y/N): Press <Y> to delete the RAID set and return to the utility main menu, or press <N> to return to the DELETE VOLUME menu. ROG STRIX X299-E GAMING 4-15...

  • Page 110: Creating A Raid Driver Disk

    Exiting the Intel Rapid Storage Technology Option ROM utility ® To exit the utility: From the utility main menu, select 6. Exit, then press <Enter>. The following warning message appears: [CONFIRM EXIT] Are you sure you want to exit? (Y/N): Press <Y>...

  • Page 111: Appendix

    Consult the dealer or an experienced radio/TV technician for help. The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. ROG STRIX X299-E GAMING...
  • Page 112 Compliance Statement of Innovation, Science and Economic Development Canada (ISED) This Class B digital apparatus complies with Canadian ICES-003, RSS-210, and CAN ICES- 3(B)/NMB-3(B). This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
  • Page 113 ASUS Recycling/Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other components as well as the packaging materials.
  • Page 114 FCC Bluetooth Wireless Compliance The antenna used with this transmitter must not be co-located or operated in conjunction with any other antenna or transmitter subject to the conditions of the FCC Grant. Bluetooth Industry Canada Statement This Class B device meets all requirements of the Canadian interference-causing equipment regulations.
  • Page 115 2014/53/EU. Cijeli di: https://www.asus.com/support/ tekst EU izjave o sukladnosti dostupan je na https://www.asus.com/support/ WiFi yang Beroperasi pada 5150-5350 MHz akan terbatas untuk penggunaan WiFi koji radi na opsegu frekvencija 5150-5350 MHz bit će ograničen na...
  • Page 116 ASUSTek Computer Inc. tukaj izjavlja, da je ta naprava skladna s temeljnimi zahtevami in drugimi relevantnimii določili Direktive 2014/53/EU. Polno besedilo izjave EU o skladnosti je na voljo na https://www.asus.com/support/ WiFi, ki deluje v pasovnem območju 5150–5350 MHz, mora biti v državah, navedenih v spodnjem seznamu, omejen na notranjo uporabo: Declaración de conformidad simplificada para la UE...

  • Page 117: Asus Contact Information

    +1-510-739-3777 +1-510-608-4555 Web site http://www.asus.com/us/ Technical Support Support fax +1-812-284-0883 Telephone +1-812-282-2787 Online support http://qr.asus.com/techserv ASUS COMPUTER GmbH (Germany and Austria) Address Harkort Str. 21-23, 40880 Ratingen, Germany +49-2102-959931 Web site http://www.asus.com/de Online contact http://eu-rma.asus.com/sales Technical Support Telephone +49-2102-5789555 Support Fax...
  • Page 118 Phone/Fax No: (510)739-3777/(510)608-4555 hereby declares that the product Product Name : Motherboard Model Number : PRIME X299-A ROG STRIX X299-E GAMING Conforms to the following specifications: FCC Part 15, Subpart B, Unintentional Radiators Supplementary Information: This device complies with part 15 of the FCC Rules. Operation is subject to the...

This manual is also suitable for:

90mb0u50-m0eay0

Table of Contents

Save PDF