Whirlpool  WED8200YW Use And Care Manual page 7

CYCLE GUIDE — MANUAL CYCLES
Settings and options shown in bold are default settings for that cycle. Not all features and cycles are available on all models.
Not all settings and options are available on each cycle. Default cycle times are estimated in minutes.
Adjusting drying time on Timed Dry Cycles
When you select a Timed Dry Cycle,
the default time appears in the display.
Use the Time Adjust buttons to increase
or decrease the time in 1 minute
increments. Press and hold to change
the time in 5 minute increments.
The maximum dry time is 90 minutes.
Cycle:
Items to dry:
Small loads and Quick Dry
sportswear
Any load Timed Dry
NOTE: Select Air
Only to dry foam,
rubber, plastic, or
heat-sensitive
fabrics
Small to medium Touch Up
loads (for non-steam
models)
Or Wrinkle Shield ™ with Steam (on some models). Wrinkle Shield
†
CYCLE GUIDE — STEAM CYCLES
Settings and options shown in bold are default settings for that cycle.
Not all settings and options are available on each cycle.
Steam cycles are designed for use with dry loads to loosen wrinkles, reduce odors, and refresh fabrics.
Items to
Cycle:
refresh:
Mixed loads Enhanced
Touch Up
Shirts, blouses, Quick
and slacks Refresh
(on some
models)
™
Or Wrinkle Shield with Steam (on some models). Wrinkle Shield
†
Load Size Recommendations
For best results, follow the load size recommendations noted for
each cycle.
Small load: Fill the dryer drum with 3-4 items,
not more than 1/4 full.
Temp: Default
Time:
13
High
Medium
Low
Extra Low
Air Only
High 40
Medium
Low
Extra Low
Air Only
High 20
Medium
Low
Extra Low
Air Only
™
Drying
Default
Temperature:
Time:
High 22
Medium
Medium 12
™
Selecting the Temp
A High heat setting may be used for drying heavyweight
items such as towels and work clothes.
A Low to Medium heat setting may be used for drying
medium-weight items such as sheets, blouses, dresses,
underwear, permanent press fabrics, and some knits.
Use a no-heat (Air Only) setting for foam, rubber, plastic,
or heat-sensitive fabrics.
Line dry bonded or laminated fabrics.
NOTE: If you have questions about drying temperatures
for various loads, refer to the care label directions.
Available
Options:
Wrinkle Shield † For small loads of 3-4 items.
Wrinkle Shield Use to dry items to a damp level for items that do
†
not require an entire drying cycle. Select a drying
temperature based on the type of fabrics in your
load. If you are unsure of the temperature to select
for a load, select the lower setting rather than the
higher setting.
Wrinkle Shield † Use this setting to help smooth out wrinkles from
such items as garments packed in a suitcase or
garments wrinkled from being left in the dryer.
with Steam is available only with High and Medium Temp settings.
Available
Options:
Wrinkle Shield Use to reduce odors and light wrinkles from small to
†
Static Reduce medium-sized loads of dry items. Dry time will
automatically adjust when the load size is sensed.
Cycle run time cannot be manually adjusted.
Temperature is selectable. Do not add dryer sheets.
Wrinkle Shield The Quick Refresh cycle is best for reducing light
†
Static Reduce wrinkles and odors from dry garments, including
loads left in the dryer. For the Quick Refresh cycle,
time is selectable in 5 minute increments, based on
the load to be refreshed.
with Steam is available only with High and Medium Temp settings.
Medium load: Fill the dryer drum up to about 1/2 full.
Large load: Fill the dryer drum up to about 3/4 full.
Do not overload. Items need to tumble freely.
Cycle Details:
Cycle Details:
7