Model UR003G Cutting tool Left hand Right hand (m/s Uncertainty K (m/s Uncertainty K (m/s (m/s 4-tooth blade Nylon cutting head Plastic blade NOTE: The declared vibration total value(s) has been measured in accordance with a standard test method and may be used for comparing one tool with another.
Page 5
Electrical safety Do not let familiarity gained from frequent use of tools allow you to become complacent and Power tool plugs must match the outlet. Never ignore tool safety principles. A careless action modify the plug in any way. Do not use any can cause severe injury within a fraction of a adapter plugs with earthed (grounded) power second.
General instructions Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and Never allow people unfamiliar with these grasping surfaces do not allow for safe handling and instructions, people (including children) with control of the tool in unexpected situations. reduced physical, sensory or mental capabil- When using the tool, do not wear cloth work gloves ities, or lack of experience and knowledge to...
During operation, keep bystanders or animals 14. If the battery cartridge gets wet, drain the at least 15 m away from the tool. Stop the tool water inside and then wipe it with a dry cloth. as soon as someone approaches. Dry the battery cartridge completely in a dry place before use.
If the tool gets heavy impact or fall, check the 26. Do not use the tool in bad weather where visi- condition before continuing work. Check the bility is limited. Failure to do so may cause fall or controls and safety devices for malfunction. If incorrect operation due to low visibility.
To avoid kickback: Always wear protective gloves when handling the cutting blade. Apply the segment between 8 and 11 o'clock. Always clean dust and dirt off the tool. Never use gasoline, benzine, thinner, alcohol or the Never apply the segment between 12 and like for the purpose.
Page 10
Do not expose battery cartridge to water also void the Makita warranty for the Makita tool and or rain. charger. A battery short can cause a large current...
Tool / battery protection system FUNCTIONAL DESCRIPTION The tool is equipped with a tool/battery protection system. This system automatically cuts off power to WARNING: Always be sure that the tool is the motor to extend tool and battery life. The tool will switched off and the battery cartridge is removed automatically stop during operation if the tool is placed before adjusting or checking function on the tool.
Indicating the remaining battery Main power switch capacity Tap the main power button to turn on the tool. To turn off the tool, press and hold the main power Press the check button on the battery cartridge to indi- button until the speed indicator goes off. cate the remaining battery capacity. The indicator lamps light up for a few seconds. ► 1 .
Page 14
To prevent the switch trigger from being accidentally Speed indicator Mode Rotation speed pulled, a lock-off lever is provided. To start the tool, High 0 - 6,500 min depress the lock-off lever and pull the switch trigger. The tool speed increases by increasing pressure on the switch trigger. Release the switch trigger to stop. UR002G Medium 0 - 5,300 min 0 - 3,500 min Automatic Torque Drive Technology When you turn on the Automatic Torque Drive...
Reverse button for debris removal ASSEMBLY WARNING: Switch off the tool and remove WARNING: Always be sure that the tool is the battery cartridge before you remove entan- switched off and battery cartridge is removed gled weeds or debris which the reverse rotation before carrying out any work on the tool.
Page 16
For UR003G Hex wrench storage Attach the upper and lower clamps on the damper. Put the handle on the upper clamp and fix it with CAUTION: Be careful not to leave the hex hex socket head bolts as illustrated. wrench inserted in the tool head. It may cause injury and/or damage to the tool. When not in use, store the hex wrench as illustrated to keep it from being lost.
Page 17
For nylon cutting head / plastic blade Correct combination of the cutting tool and the protector CAUTION: Take care not to injure yourself on the cutter for cutting the nylon cord. CAUTION: Always use the correct combi- Attach the protector to the clamp using bolts. After nation of cutting tool and the protector.
To remove the cutter blade, follow the installation proce- dures in reverse. Nylon cutting head NOTICE: Be sure to use genuine Makita nylon cutting head. ► 1 . Nut 2. Cup 3. Clamp washer 4. Cutter blade 5. Spindle 6. Receive washer 7. Hex wrench Insert the hex wrench through the hole in the tool head to lock the spindle.
Plastic blade For UR002G Put on the shoulder harness and fasten the NOTICE: Be sure to use genuine Makita plastic buckle. blade. Clasp the hook on the shoulder harness to tool's hanger. ► 1 . Plastic blade 2. Spindle 3. Hex wrench 4. Loosen 5.
Page 20
The shoulder harness features a means of quick Adjust the shoulder harness to a comfortable release. working position. Simply squeeze the sides of the buckle to release the shoulder harness. The shoulder harness features a means of quick release. ► 1 . Buckle Simply squeeze the sides of the buckle to release the tool from the shoulder harness.
Page 21
Adjust the hanger position as shown in the figure Correct positioning and handling allow optimum control and then tighten the hex socket head bolt. and reduce the risk of injury caused by kickback. UR002G 750 mm 100-300 mm 750 mm The hanger position from the ground UR003G The cutting tool position from the ground The horizontal distance between the hanger and the unguarded part of the cutting tool Correct handling of the tool WARNING:...
Discoloration, deformation or cracks may result. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Replacing the nylon cord WARNING: Use only the nylon cord with diameter specified in this instruction manual.
► 1 . Arrow on the protector 2. Arrow on the blade TROUBLESHOOTING Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual, do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using Makita replace- ment parts for repairs. State of abnormality Probable cause (malfunction) Remedy Motor does not run.
The use of any other accessory or attachment may result in serious personal injury. CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.