Related Manuals for Vizio XMF1000
Summary of Contents for Vizio XMF1000
- Page 1 QUICK INSTALL SLIM HDTV MOUNT UNIVERSAL FOR 32” - 55” TVS UP TO 100 LBS XMF1000 - QUICK INSTALL GUIDE...
-
Page 2: Important Safety Information
IMPORTANT SAFETY INFORMATION Read the Important Safety Information on this page before installing or using this mounting system. Always follow the instructions in this Quick Install Guide. VIZIO is not liable for damage or injury caused by incorrect mounting, assembly, or use. -
Page 3: Step 1 - Before You Begin
STEP 1 - BEFORE YOU BEGIN Before you begin the installation, ensure you have all of the items listed on this page. Do not begin the installation unless you have all of the following items. Mounting a TV requires power tools. If you are unfamiliar with safe power tool use, consult a professional installer. - Page 4 STEP 2 - REVIEW THE PACKAGE CONTENTS Before you begin, ensure all parts are included and undamaged. To prevent loss, do not unpack the small parts until they are required. If any parts are missing or damaged, contact VIZIO Customer Service (877) 698-4946.
- Page 5 [ M4 x 44 ] [ M4 x 15 ] [ M5 x 44 ] [ M5 x 15 ] [ M6 x 44 ] [ M6 x 20 ] [ M6 x 15 ] [ M8 x 48 ] [ M8 x 20 ] MISC ANCHOR...
- Page 6 STEP 3A - MOUNTING TO A WALL WITH WOOD STUDS The mount can be attached to walls with wood studs. The wall covering (drywall, lath, plaster, etc.) may not be thicker than 1/2”. If you are mounting on a concrete wall, go to Step 3B on page 10. 1.
- Page 7 3. Remove 1 lag bolt and 1 washer from the pouch labeled LAG. Place part A against the wall as shown, and use a wrench to insert the lag bolt and washer into the hole you just drilled. 4. Push the bar through the opening in the bracket (part A) as shown.
- Page 8 5. Remove the bar, the leveler, and the unattached bracket (part A) from the wall. Using the power drill and the 7/32” drill bit, drill into the pencil mark as shown. Ensure you are drilling into the stud. Drill the hole about 2” into the stud. 6.
- Page 9 7. Push the bar through the openings in each bracket (part A) as shown. Snap on the leveler (part E) and verify that the bar is level. Make any small adjustments, then use a wrench to tighten the 2 lag bolts completely. The bar can be inserted from right to left or left to right, depending on the end of the bar to which you would like the handle attached.
- Page 10 9. Remove 2 lag bolts and 2 washers from the pouch labeled LAG. Use a wrench to insert the lag bolts and washers as shown. Tighten the bolts completely. 10. Attach the handle (part F) to the end of the bar. Secure the handle to the bar by inserting a screw (part H) into the bottom hole on the handle.
- Page 11 OPTIONAL: The extender can be attached to lengthen the bar. A longer bar may be easier to access when mounting large TVs. To attach the extender, push it onto the end of the bar. Secure the extender to the bar by inserting a screw (part H) into the bottom hole on the extender.
- Page 12 STEP 3B - MOUNTING TO A CONCRETE WALL 1. Determine the height at which you want the mount to hang. Mark the position of the left bracket hole with a pencil. Using the power drill and the 1/2” concrete drill bit, drill a hole into the pencil mark.
- Page 13 3. Remove 1 lag bolt and 1 washer from the pouch labeled LAG. Place a bracket (part A) against the wall as shown, and use a wrench to insert the lag bolt and washer into the anchor. 4. Push the bar through the opening in the bracket (part A) as shown.
- Page 14 5. Remove the bar, the leveler, and the unattached bracket (part A) from the wall. Allow the attached bracket to swing down. Using the power drill and the 1/2” concrete drill bit, drill into the 3 pencil marks as shown. Drill each hole about 2 1/2” deep. 6.
- Page 15 7. Remove 3 lag bolts and 3 washers from the pouch labeled LAG. Place the other bracket (part A) against the wall as shown, and use a wrench to insert the lag bolts and washers into the anchors. Do not insert the lag bolts completely. Leave 1/2” of the bolts showing.
- Page 16 9. Attach the handle (part F) to the end of the bar. Secure the handle to the bar by inserting a screw (part H) into the bottom hole on the handle. Tighten the screw completely. Insert Screw in Bottom Hole OPTIONAL: The extender can be attached to lengthen the bar.
- Page 17 STEP 4 - ATTACHING THE TV HOOKS AND KICK STANDS 1. Gently place the TV on the floor screen-down. You may want to place a rug or blanket beneath the screen to prevent scratches. In your TV’s User Guide, find the size and depth of your TV’s mounting holes.
- Page 18 (part G) and the longer screws when mounting the TV hooks. 3. Using the screwdriver, insert the screws and washers as shown. Because each TV is different, your VIZIO TV mount includes screws of different lengths. Use screws that can be inserted completely.
- Page 19 4. Place the two kickstands (parts C and D) against the two bottom mounting holes as shown. The larger kickstand can be placed on either the left or right mounting hole. 5. Using the screwdriver, insert the screws and washers as shown. Do not use a short screw if a longer screw can be inserted completely.
- Page 20 STEP 5 - HANGING THE TV ON THE MOUNT This step requires lifting the TV. To prevent injury to yourself or damage to your TV, perform this step with the help of another person. 1. Turn the handle on the bar until the flat side of the bar is facing the wall.
- Page 21 3. Turn the handle on the bar until the flat side of the bar is facing down. Ensure the flat side of the bar is facing down. This locks the TV to the bar. If the flat side of the bar is not facing down, your TV is not locked to the bar.
-
Page 22: Technical Support
Customer support and quality service are integral parts of VIZIO’s commitment to service excellence. For technical assistance contact our VIZIO Technical Support Department via email or phone. Please have your VIZIO model number, serial number, and date of purchase available before your call. Address:... -
Page 23: One-Year Limited Warranty & Insurance
VIZIO determines that the VIZIO bracket has been improperly installed, altered in any way or tampered with; or if it is determined by VIZIO that the damage did not result from the VIZIO product’s failure or that in fact no occurrence took place; or the repair or replacement of the damaged Component is covered under a manufacturer’s warranty;... - Page 24 TRADEMARKS SHOWN ARE THE PROPERTY OF THEIR RESPECTIVE OWNERS. IMAGES USED ARE FOR ILLUSTRATION PURPOSES ONLY. VIZIO, THE V LOGO, WHERE VISION MEETS VALUE, AND OTHER VIZIO TRADEMARKS ARE THE INTELLECTUAL PROPERTY OF VIZIO INC. PRODUCT FEATURES AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Need help?
Do you have a question about the XMF1000 and is the answer not in the manual?
Questions and answers