Table of Contents
Advertisement
Quick Links
c.LOGiC-Interface
CI-C1-RNSE
Compatible with navigation systems
Audi Navi Plus RNS-E
Only for vehicles WITHOUT factory rear-view camera
Product features
• full plug and play multimedia interface
• 1 AV-input with separate IR-control channel
• control of after-market devices, e.g. DVB-T tuner, DVD-player, DVD-changer, ...
• after-market rear-view camera input
• automatic switching to rear-view camera input (optional coding necessary to switch from
OEM-modes)
• rear-view camera power (+12V max. 1A)
• rear-seat-entertainment AV-output
• power on remote out trigger signal (+12V ma.x 1A) to switch on connected devices
Version 08.12.2015
CI-C1-RNSE
Advertisement
Table of Contents
Related Manuals for Car-Interface CI-C1-RNSE
Summary of Contents for Car-Interface CI-C1-RNSE
- Page 1 CI-C1-RNSE Compatible with navigation systems Audi Navi Plus RNS-E Only for vehicles WITHOUT factory rear-view camera Product features • full plug and play multimedia interface • 1 AV-input with separate IR-control channel • control of after-market devices, e.g. DVB-T tuner, DVD-player, DVD-changer, …...
-
Page 2: Table Of Contents
AV-source 3.3.2. Installing AV-source’s IR-sensor additionally 3.3.3. After-market rear-view camera 4. Operation 4.1. Selecting the c.LOGiC as current AV-source 4.2. Assigning device control 4.3. Remote functions 4.4. Picture settings 5. Specifications Appendix A – Device control table Version 08.12.2015 CI-C1-RNSE... -
Page 3: Prior To Installation
Take down the SW-version and HW-version of the interface boxes, and store this manual for support purposes. Harness C1C-RNSE Interface-box C1C-M01 HW_____ SW_____ If remote function for the connected devices shall be used, additional an IR- remote cable and Y-adapter are needed, see chapter AV-source . Version 08.12.2015 CI-C1-RNSE... -
Page 4: Check Compatibility Of Vehicle And Accessories
Only compatible with NTSC-cameras. camera Automatic switching to camera from OEM mode only works after coding the head-unit to rear-view camera per diagnosis computer (Only possible on RNS-E with minimum software 550 and till year 2010). 2. Connection schema Version 08.12.2015 CI-C1-RNSE... -
Page 5: Installation
In case the sleep-mode does not show success, disconnect the battery with a resistor lead. Place of installation is behind the head-unit. 3.1. Interconnecting Interface-box and harness Plug harness C1C-RNSE into 12pin Molex of Interface-box C1C-RNSE. Version 08.12.2015 CI-C1-RNSE... -
Page 6: Connections To Head-Unit
Pin 9 CAN HIGH 9 Pin 10 CAN LOW Quadlock male of vehicle No liability for vehicle wire colors and pin definition! Possible changes by the vehicle manufacturer. The given information must be verified by the installer. Version 08.12.2015 CI-C1-RNSE... -
Page 7: Connecting Peripheral Devices
C1C-M01 with the AV-output of the AV-source. The pink ACC-output wire (+12V max. 1A) of the 4pin cable can be connected to the ACC-input wires of the connected device to switch it on. It carries +12V when the head-unit is running. Version 08.12.2015 CI-C1-RNSE... -
Page 8: Installing Av-Source's Ir-Sensor Additionally
2010). If coding is done by diagnosis PC, code rear-view camera to value 1 in channel 04, controller 56. After coding the vehicles needs to be locked for at least 66 minutes to reach general sleep mode. Version 08.12.2015 CI-C1-RNSE... -
Page 9: Operation
The function description equals the remote control buttons of the optional c.LOGiC remote control or the additional device. On the additional device the writing may vary (e.g. AV instead of Source). Version 08.12.2015 CI-C1-RNSE... -
Page 10: Picture Settings
Press the knob to change from brightness to colour and contrast (after contrast, the interface starts again with brightness). Turn the knob to change the current picture value. To quit the settings menu press RETURN-button. Version 08.12.2015 CI-C1-RNSE... -
Page 11: Specifications
-30°C to +80°C Weight Measurements (box only) B x H x T 106 x 30 x 71 mm Legal disclaimer: Mentioned company and trademarks, as well as product names/codes are registered trademarks ® of their corresponding legal owners. Version 08.12.2015 CI-C1-RNSE...
Need help?
Do you have a question about the CI-C1-RNSE and is the answer not in the manual?
Questions and answers