Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Vestax PMC 500
Summary of Contents for Vestax PMC 500
- Page 1 OWNER'S MANUAL...
-
Page 2: Table Of Contents
CONGRATULATIONS ！ Thank you for purchasing the Vestax PMC-500 Professional Mixing Controller. We suggest that you read through this owner's manual thoroughly so that you may enjoy the full use of this product safely and in the knowledge of all its special features and suitable applications. -
Page 3: Inportant Safeguards
I M P O R T A N T S A F E G U A R D S READ BEFORE OPERATING EQUIPMENT This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of. -
Page 4: Specifications
15. Damage Requiring Service-Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is damaged. b. If liquid has been spilled or objects have fallen into the product. -
Page 5: F E A T U R E S
(1/4) and two (2) band EQ (HI, LOW). Both channels are also switch able to line channels with a LED indicating which channel is active ・Quality Vestax cross replaceable) with four pre-selectable cross fader curve settings for long or short mixing (scratching and cutting). -
Page 6: Program Input Section
See "HOW TO CHANGE THE INPUT FADER UNIT". *Replace this fader with a Vestax IF-500 replacement inputfader. so as to established . This signal can be sent to position of the crossfader. -
Page 7: Crossfader Section
This fader is user replaceable and may be changed easily by following this user guide's instructions carefully. See"HOW TO CHANGE THE CROSSFADER". *Replace this fader with a Vestax CF-PCV replacement inputfader. @0 C .F. CURVE SELECT SWITCH Adjusts the crossfader curve. A clockwise rotation... -
Page 8: Master Section
MASTER SECTION @6 M ASTER BALANCE 1&2 Adjusts the signal balance of the L to R side of the outputs from MASTER OUT 1&2 JACKS rear panel. @7 M ASTER LEVEL 1&2 Adjusts the signal level outputs from MASTER OUT 1&2 JACKS on the rear panel. -
Page 9: Rear Panel
PGMs to be heard through the booth monitor section. Please consult a Vestax Technical Support Representative before attempting any such modification. %4 P OWER SWITCH Power on/off. %5 P OWER JACK Connect the Vestax AC-20 , AC adaptor. - Page 10 %4 FIRE EVACUATION CONTROL (JACK) This feature has been added in order to ensure that venues using the PMC-500 are in compliance with modern fire safety standards. If a Fire Alarm is correctly connected to the PMC-500 and is triggered in an evacuation emergency, the PMC-500 will react to such a signal (alarm) by swiftly canceling the Connection to the Fire Evacuation Control Jack can be accomplished as illustrated.
-
Page 11: How To Change The Fader Unit
HOW TO CHANGE THE INPUTFADER UNIT Change to "IF-500" ■ q Re1.Remove the fader knobs. (See fig-a) w Remove the 4 screws which fix the input fader panel to the mixer. (See fig-b) e Remove the 2 screws which fix the input fader. (See fig-c) r Remove the input fader, and carefully remove the multi-cable connector from the fader unit. - Page 12 HOW TO CHANGE THE CROSSFADER UNIT Change to "CF-PCV" ■ q Remove the fader knob and 3 screws which fix the crossfader panel, and the carefully remove the panel. (See fig-e) w Remove the 2 screws affixing the crossfader unit. (See fig-f) e Carefully remove the multi-cable connector from the fader unit.
-
Page 13: Block Diagram
BLOCK DIAGRAM... - Page 16 AUG.2003 PMC-500Eq Vestax Corporation...
Need help?
Do you have a question about the PMC 500 and is the answer not in the manual?
Questions and answers