Advertisement
[Louver removal/installation procedure]
Louver removal procedure
product,
tallation
two M5
evice so
Open
his time
agram to
Turn the louver in the direction
of the arrow.
Louver installation procedure
When installing the louver to the main unit, align and insert the tongue of the
louver into the groove of the main unit. After inserting the tongue into the groove,
turn the louver clockwise to install.
* Do not touch inside the device when removing and installing the louver, otherwise accidents
or problems with operation may occur.
[Discharge needle unit removal/installation procedure]
When using a ultrasonic cleaner for cleaning,
remove the discharge needle unit.
Fan
Discharge needle unit removal procedure
peration
ON
OFF
OFF
Louver (Note: 1)
ON
and back
Discharge
needle unit
Hold the louver and turn the discharge needle
unit counterclockwise. (Note: 2)
Discharge needle unit installation procedure
As shown in the � gure above, install the louver and the discharge needle unit so that
the claw of the louver is inserted into the hole of the discharge needle unit. (Note: 3)
Turn the discharge needle unit clockwise until it stops to install.
Notes: 1) If replacing the louver, install the discharge needle unit to the replacement louver.
Notes:
2) When turning the discharge needle unit, do not apply any more force than is necessary,
otherwise the louver or the discharge needle unit may become damaged.
Notes:
3) ���� rm the side of the discharge needle unit to install. If installed on the wrong side, the
discharge needle unit or the louver may become damaged.
Option (sold separately)
ER-F12ANT : Discharge needle unit x 1
Cleaning and replacement procedure for fan � lter
ouver to
Install a � �lter in accordance with the operating environment.
Remove the � �lter cover. Disengage the clasps in the places indicated by
below, and then pull the � �lter cover in the direction of the arrow to remove it. (Refer to the
es where
illustration below.)
e away.
Clean away any dust and dirt adhering to the � �lter. If the � �lter is particularly dirty,
wash it in water. If washing the � �lter in water, let it dry thoroughly before reusing it.
er a wide
Install the � �lter. Install the � �lter cover.
* If the device is used while the � �lter is still wet, accidents or problems with operation may occur.
replace it
* If the � �lter will not come clean, it should be replaced.
7
CARE
* Be careful not to let anything get inside the device while the � �lter is removed.
Option (sold separately)
ed.
ER-F12FX5 : Replacement � �lter x 5
needle.
es may
dles and
drop and
sing the
ce is not
8
TROUBLESHOOTING
ded that
ace the
Be sure to turn off the power before checking the discharge unit or the fan unit.
Problem
Main cause
he main
Discharge error
Condensation
ar tools
indicator (DSC
Foreign objects
d them.
ERROR)
F.G. not connected
oistened
lights up.
ove the
dle unit
Fan error indicator
Fan is covered
unit well.
(FAN ERROR)
Fan is blocked
louver.
lights up.
Foreign objects
Ramco National
Groove of the
main unit
Remove the louver from the main unit.
Hole of the discharge
Claw of the louver
needle unit
Details of the
central part
Remove the discharge needle unit from the
louver to the direction shown in the figure.
Main unit
Filter cover
Filter
Main unit
Filter cover
Remedy
�� An abnormal discharge is probably occurring.
Turn off the power and check that the tip of the
discharge needle is intact and free from foreign objects,
and also check that the discharge needle unit is
correctly installed to the louver.
�� If the error indicator remains lit even after the discharge
needle has been cleaned, check if the area around the
needle is dirty.
������������������.G. terminal is securely grounded.
�� Turn off the power and check that the � lter is not dirty or
blocked.
�� Check that there are no foreign objects inside the
product.
9
SPECIFICATIONS
Item
Charge removal time
Ion balance
Power supply voltage
Power consumption
Discharge method
Discharge output voltage
Max. fan speed
Max. fan volume
Tongue of the
Error output
louver
Output operation
Short-circuit protection
Discharge halt output
POWER
DSC
DSC ERROR
FAN ERROR
Ozone generation amount
Ambient temperature
Ambient humidity
Vibration resistance
Material
Grounding method
Weight
Accessories
Notes: 1) Typical value at 200 mm from directly in front of discharge outlet, fan speed MAX, straight
louver, with no � �lter installed.
Notes:
2) Typical value at 300 mm from directly in front of discharge outlet, fan speed MAX, straight
louver, with no � �lter installed.
Notes:
3) The discharge needle unit is loaded on the straight louver before shipment.
10
CAUTIONS
This product has been developed / produced for industrial use only.
Do not use this product for any purpose other than charge removal and dust removal.
Do not use this product in enviroments which are outside the ������ cation range,
otherwise operating problems or damage may occur. In addition, the operating life
�������������������������������� cantly reduced.
Never disassemble, repair or modify this product, otherwise operating problems or
accidents may occur.
Do not dispose of this product by burning it, otherwise it may explode or toxic
fumes may be generated.
This product generates ozone, so be sure to provide adequate ventilation if using it
��������� ned space.
Do not run the wires together with high-voltage lines or power lines or put them in
the same raceway. This can cause malfunction due to induction.
Be sure to turn off the air and the power supply before carrying out any cable
in the illustration
connection or inspection work. If this is not done, operating problems, damage or
electric shocks may occur.
After connecting the cables, check that the connections are correct before turning on the
power. If the cables are connected incorrectly, operating problems or accidents may occur.
Verify that the supply voltage variation is within the rating.
It takes approximately 5 seconds after the power is turned on before the fan
operation stabilizes. To ensure proper charge removal performance, do not use the
������������������ cient time has elapsed.
Do not turn the power back on immediately after it has been turned off, otherwise
operating problems or accidents may occur. In addition, the operating life of the
product may become ������ cantly reduced. Wait at least 2 seconds before turning
the power back on again.
Do not use any cables which have any damage (such as splitting or cracking),
otherwise operating problems or accidents may occur.
Avoid using the product in places where there are high levels of steam or dust in
the air or where it might be directly exposed to water, oil or welding spatter.
Do not touch the discharge needle with hard objects such as tools. If the discharge
needle becomes broken, it will not provide ���� cient charge removal performance,
and moreover operating problems or accidents may occur.
Do not use this product while the � �lter is blocked, otherwise accidents or problems
with operation may occur.
Clean or replace the � �lter at regular intervals.
Be sure to turn off the power before replacing the � �lter.
Install the product so that it is at least 100 mm away from the objects being charged.
When installing this product, be sure to securely install the main unit and the
bracket. If they are not securely installed or if constant vibration or shocks are
applied, accidents or problems with operation may occur.
Do not place any objects which may obstruct air � �ow within 20 mm the front of the
fan air intake, otherwise accidents or problems with operation may occur.
Use cables that are 0.15 mm
Also, keep the wiring as short as possible in order to prevent naise.
If this product ceases functioning or is no longer required, dispose of it according to
appropriate local waste disposal regulations.
http://panasonic.net/id/pidsx/global
Overseas Sales Division (Head Office)
2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan
Phone: +81-568-33-7861 FAX: +81-568-33-8591
About our sale network, please visit our website.
PRINTED IN CHINA
800-280-6933 | nsales@ramcoi.com
Type
Standard fan type
Model No.
ER-F12
1 sec. approx. (Note 1)
±10 V or less (Note 2)
24 V DC ±10%
700 mA or less
High-frequency AC method
±2 kV approx.
5.3 m/s (Note 2)
3
3.68 m
/min
NPN transistor/open collector
��������������������������
��Applied voltage: 30 V DC or less (between output terminal and 0 V)
�����������������������������������������������������������
OFF when discharge error or fan error detected
Normally ON
Incorporated
Discharge halt: Short-circuited to 0 V
Discharge (operation start): Open
Green LED (Lights up when power on)
Green LED (Lights up during normal discharge)
Red LED (Lights up when discharge error detected)
Red LED (Lights up when fan error detected)
0.04 ppm or less (Note 1)
0 to + 50°C (No dew condensation) / Storage : -10 to + 65°C
35 to 65% RH (No dew condensation) / Storage : 35 to 65% RH
10 to 55 Hz frequency, 0.75 mm amplitude in X, Y and Z directions for two hours each
Enclosure: ABS Louver: ABS Discharge needle: Tungsten
Discharge needle unit: PBT Bracket: SPHC
C (capacitor) grounding
790g approx. (main unit only)
● Louvers ● Caution label: 1 set
Straight louver: 1 (Note 3 ) ● Rubber cushion: 1
Angle louver: 1
2
or more and 30 m or less in length for wiring.
© Panasonic Industrial Devices SUNX Co., Ltd. 2012
www.panasonicsensors.com
Low-volume fan type
ER-F12S
1.5 sec. approx. (Note 1)
±10 V or less (Note 2)
24 V DC ±10%
400 mA or less
High-frequency AC method
±2 kV approx.
4.0 m/s (Note 2)
3
2.50 m
/min
Advertisement
