Table of Contents
Advertisement
129.2cc 40cm HAND PUSH
PETROL LAWNMOWER
ITEM NO. 484341
Model No. XSS40H2
INSTRUCTION MANUAL
Please read these instructions fully before starting assembly.
HHGL Limited, Witan Gate House, 500-600 Witan Gate, Milton Keynes, MK9 1BA
Technical Support & Parts
01904 727509
Mon-Fri 9am-5pm Sat-Sun 11am-4pm
www.gardenservicecentre.co.uk
Oct 17
Advertisement
Table of Contents
Related Manuals for Sovereign XSS40H2
Summary of Contents for Sovereign XSS40H2
- Page 1 129.2cc 40cm HAND PUSH PETROL LAWNMOWER ITEM NO. 484341 Model No. XSS40H2 Technical Support & Parts 01904 727509 Mon-Fri 9am-5pm Sat-Sun 11am-4pm www.gardenservicecentre.co.uk INSTRUCTION MANUAL Please read these instructions fully before starting assembly. HHGL Limited, Witan Gate House, 500-600 Witan Gate, Milton Keynes, MK9 1BA...
-
Page 2: Table Of Contents
CONTENTS GENERAL SAFETY WARNINGS SAFETY WARNINGS WARNING! Read all safety warnings and General safety warning instructions. Intended use Failure to follow the warnings and instructions Warnings symbols may result in fire and/or serious injury. In the box WARNING! Read all safety warnings and Preparing to assemble the lawnmower instructions designated by the symbol. - Page 3 GENERAL SAFETY a) Refuel outdoors only and do not smoke while refueling. • Keep this operating and maintenance manual in a safe place for reference at a later date. b) Add fuel before starting the engine. Never remove the cap of the fuel tank or add petrol while the •...
- Page 4 • Exercise extreme caution when changing a) Before clearing blockages or unclogging the chute. direction on slopes. b) Before checking, cleaning or working on the • Do not mow excessively steep slopes. lawnmower. • Use extreme caution when reversing or pulling c) After striking a foreign object, inspect the the lawnmower towards you.
-
Page 5: Intended Use
INTENDED USE Hot surfaces will burn fingers or palms. This mower is designed for domestic lawn mowing only. Use in any other way is considered contrary to the intended use. Compliance with the operation, service and repair, as specified in this handbook, also constitutes essential elements of the Warning! The lawnmower exhaust gas contains toxic intended use. -
Page 6: In The Box
IN THE BOX PREPARING TO ASSEMBLE THE LAWNMOWER PARTS A. Main mower deck (with upper handle attached) B. Lower handle WARNING! Always take care when removing the packaging, to prevent C. Grass collecting bag x 1 damage to you or to the lawnmower. D. - Page 7 STEP 2 - ASSEMBLE THE UPPER HANDLE STEP 3 - ASSEMBLE THE GRASS BAG 3a. Firstly, attach the grass bag to the frame by fixing all plastic hooks. 3b. Raise the safety flap, and hook the collection bag onto the mower.
-
Page 8: Preparing To Operate The Lawnmower
Running the engine with a low oil level will cause irreparable 5. Tighten the filler cap after filling, finger tight only. engine damage. NOTE! The Sovereign 40cm Hand Push Lawnmower has a Check the engine oil level with the engine stopped and the maximum fuel capacity of 900ml. -
Page 9: Operating The Lawnmower
OPERATING THE LAWNMOWER STEP 2 - STARTING THE ENGINE STEP 1 - SETTING THE CUTTING HEIGHT WARNING! Do not operate the machine in enclosed or poorly ventilated areas as the exhaust gas contains toxic WARNING! The blade can cause serious injury. Before substances. - Page 10 Pressing the primer button too many times could cause the C. Pull the stop/start bar towards the upper handle. engine to flood. D. Operate the starter as described above. NOTE! When starting a warm engine, the primer does not need to be used.
-
Page 11: Maintenance
STEP 4 - EMPTYING THE GRASS BAG STORING THE LAWNMOWER FOR EXTENDED PERIODS CAUTION! Do not empty the petrol tank in enclosed areas, near fire or when smoking. Petrol fumes can cause explosions and fire. If the lawnmower is to be placed into storage at the end of the season, or if the mower is not to be used for a longer period than 6 weeks, storage maintenance must be performed on the lawnmower. - Page 12 PREPARATION TO RE-USE CLEANING Check the oil level before starting the engine and ensure there is To ensure long life and good performance of the machine, it’s sufficient oil, see page 7. important to keep the machine clean and well lubricated. Make sure the chute is clean and under the deck is cleared from wet Check the spark plug is inserted correctly, see page 24.
- Page 13 CLEANING OR REPLACING THE SPARK PLUG REPLACING THE CUTTING BLADE 0.7-0.8 mm WARNING! USE GLOVES. - Before you remove the grass collection bag, stop the engine and wait until the blade stops completely. - You will need garden gloves (not provided) and a spanner wrench to remove the blade.
-
Page 14: Troubleshooting
TROUBLESHOOTING 1. Tip the machine slightly towards the oil filler pipe and reach under the deck. WARNING! 2. Hold the blade and unscrew the blade bolt counterclockwise - Always switch off the engine and pull the ignition cable using a spanner wrench. Remove the washer and the blade. before starting any inspection or adjustment work. -
Page 15: Technical Data
DISPOSAL Unsatisfactory Cutting height is too Set correct grass collection height The lawnmower and its accessories are made of various Blade is worn Replace the recyclable materials. Dispose of the lawnmower in accordance grass bag is clogged blade with your local recycling regulations. Empty the grass bag GETTING HELP... -
Page 16: Warranty
Warranty Any claim under this warranty must be made within 12 months of the date of purchase. To make a claim under the warranty, take the product (with proof of purchase) to your local store. HHGL Limited bears reasonable, direct expenses of claiming under the warranty.
Need help?
Do you have a question about the XSS40H2 and is the answer not in the manual?
Questions and answers
Gap of spark plug for the mower
The spark plug gap for the Sovereign mower with part number XSS40H2 is 0.7mm.
This answer is automatically generated
How to fill with engine oil
To fill engine oil in a Sovereign XSS40H2 lawnmower:
1. Ensure the engine is stopped and the mower is on a level surface.
2. Remove the oil filler dipstick and wipe it clean with a cloth.
3. Insert the dipstick into the oil filler neck without screwing it in.
4. Fill the engine with the recommended oil grade, ensuring not to overfill.
5. Check the oil level using the dipstick.
6. Tighten the filler cap finger tight after filling.
7. Clean up any oil spills before starting the engine.
Running the engine with a low oil level can cause irreparable damage.
This answer is automatically generated
Is it through where dip stick is. If so it is in such an awkward position. Even using funnel because where its located you spill half of the oil.
Is there a telephone number that U can speak with someone