Preparation 1 - Hitachi HDB60 Instruction Manual

All manuals and user guides at all-guides.com

PREPARATION 1

SWITCHING ON
Turn on your TV set and select the SCART input (with
the AV key, or similar, on thetelevision remote
control). Turn on the mains supply to the HDB60
receiver (the indicator on the front of the receiver
will glow red) and press the [STANDBY] key on the
HDB60remote control handset. The indicator light
will glow green and the receiver's menu will be seen
on the TV screen.
If you do not see the receiver's menu on the
television screen, refer to the Troubleshooting Guide
in Appendix E.
TUNING IN
Because this is the first time that the receiver has
been used, there are no channels stored in the
receiver's memory and the First Time Installation
menu is displayed on the screen.
Q yr h † rà p u ‚ ‚ †rà U Wà U ’ƒ rà ˆ †v  tà à à à à à xr ’†
6(/(&7
Q …r ††Ã à à à à à ‡‚à †‡ h …‡ à v †‡h yyh ‡v ‚ 
First you should select the type of TV set you have
connected to the HDB60receiver. Press the [LEFT]
or [RIGHT] keys on the remote control handset to
switch the indicator on the screen to show either
16:9, if you have a 16:9 or 'widescreen' TV, or to 4:3
if you have a standard TV set. Then press [SELECT]
to start the installation process. The next menu will
ask if you want to tune in the digital terrestrial
television channels.
Using the [LEFT] or [RIGHT] keys on the remote
control, make sure that the YES button is highlighted
in yellow, and press the [SELECT] key to start the
automatic search.
9 ‚à ’‚ ˆÃ  h  ‡ à ‡‚à †‡ h …‡ à h ˆ ‡ ‚ € h ‡ v pà †r h …p u 4
`r†
I P S H 6GÃ #)"
I ‚
- 7 -
The HDB60 receiver will automatically tune to the
UHF transmission channels 21 to 68 looking for
digital terrestrial TV broadcasts and displaying the
names of channels found. This process will take
about five minutes.
When the search is finished, the first channel of the
channel list and the information banner is displayed
you can now watch digital terrestrial television,
selecting the channel you require as described in
the next section.
HINT
Depending on the reception conditionsin your
particular area, you may find that the list of
channels found includes one or more repeated
names. This is because the receiver may detect
and store some channels, including those it
cannot receive clearly, from adjacent areas
a l o n g s i d e t h e s t r o n g c h a n n e l s f r o m a
transmitter nearby. This is not a problem and
the weaker channels can be deleted from the
receiver later, as described in Section 3 -
ADVANCED OPERATION - Editing the channel
list.
If no digital terrestrial television broadcasts are
found the receiver will display a message:
You should then refer to the Troubleshooter Guide
in Appendix E to establish the cause of the problem.
When you have finished watching digital terrestrial
TV, you may wish to switch the receiver to standby
to save power - although the HDB60receiver can
remain powered up continuously, even when the
television is turned off, without harm to the
television or itself. The receiver is returned to
standby by pressing the [STANDBY] key on the
remote control handset.
Hint
In standby, the HDB60 receiver still consumes
power and thereby contributes to air and water
pollution and the exhaustion of the World's
natural resources. Overnight, or when your
receiver is not going to be used for long
periods of time, you can turn it off at the mains
and this will save energy (and save you money).
You will not have to re-install the receiver when
it is turned on again.