COLOR TELEVISION RECEIVER Chassis : KS1A(P) Model : CZ20F12TSXVXEH RTV servis Horvat Tel: ++385-31-856-842 Tel/fax: ++385-31-856-139 Mob: 098-788-319 www.rtv-horvat-dj.hr COLOR TELEVISION RECEIVER CONTENTS Precautions Specifications and IC Data Disassembly and Reassembly Alignment and Adjustment Troubleshooting Exploded View and Parts List...
Page 2
Precautions 1. Precautions Follow these safety, servicing and ESD precautions to prevent damage and protect against potential hazards such as electrical shock and X-rays. 1-1 Safety Precautions 1. Be sure that all of the built-in protective devices are replaced. Restore any missing (READING SHOULD NOT BE ABOVE protective shields.
Page 3
14. Components, parts and wiring that appear to have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheat- ing, and correct any potential hazards. www.rtv-horvat-dj.hr www.rtv-horvat-dj.hr Samsung Electronics...
Page 4
Precautions 1-2 Servicing Precautions Warning1: First read the “Safety Precautions” section of this manual. If some unforeseen circumstance creates a conflict between the servicing and safety precautions, always follow the safety precautions. Warning2: An electrolytic capacitor installed with the wrong polarity might explode. 1.
Page 5
4. Do not use freon-propelled chemicals. These unpackaged replacement ESDs. Motions such can generate electrical charges that damage as brushing clothes together, or lifting a foot ESDs. from a carpeted floor can generate enough static electricity to damage an ESD. www.rtv-horvat-dj.hr www.rtv-horvat-dj.hr Samsung Electronics...
Disassembly and reassembly 3. Disassembly and Reassembly 3-1 Back Cover Removal 1. After removing the screws, press the tension rib and pull the cabinet backwards. 2. To reassemble, press the tension rib (see diagram). www.rtv-horvat-dj.hr www.rtv-horvat-dj.hr Samsung Electronics...
Page 10
3. Remove the main board by pulling it with both hands. Warning: The FBT is charged with high voltage. Before removing the Anode Cap, discharge the voltage through one of the heat sinks on the main board. www.rtv-horvat-dj.hr www.rtv-horvat-dj.hr Samsung Electronics...
Page 11
Disassembly and reassembly 3-3 Speaker Removal 1. Remove the speaker by pressing the tension rib. 1. Remove the screws. 2. Remove the speaker by pressing the tension rib. www.rtv-horvat-dj.hr www.rtv-horvat-dj.hr Samsung Electronics...
Page 12
Always lift the picture tube by grasping it firmly around the faceplate, (2) Never lift the tube by its neck. (3) Do not scratch the picture tube or apply excessive pressure. Fractures of the glass may cause an implosion. www.rtv-horvat-dj.hr www.rtv-horvat-dj.hr Samsung Electronics...
3. Access the Adjustment Mode by pressing the “VOLUME” keys ( Up or Down). The adjust- ment parameters are listed in the accompany- ing table, and selected by pressing the CHAN- NEL keys ( , ). www.rtv-horvat-dj.hr www.rtv-horvat-dj.hr Samsung Electronics...
Page 14
SE CAM - L V i s i o n I F 0 ~ 1 T XP T T X P o s i t i o n 0 ~ 1 5 NOTE : PVS,PVA, PHS, parameters must be aligned using the 50Hz vertical-field rates. www.rtv-horvat-dj.hr www.rtv-horvat-dj.hr Samsung Electronics...
Page 15
Alignment and Adjustments 4-2-3 Option Bytes In the Service Mode, various can be selected via the Option Table. Example: Option Table : xx xx xx xx SYSTEM AUDIO MONO JACK ZOOM NOR/ZOOM/16:9 AUTO POWER 2nd SIF HOTEL MODE www.rtv-horvat-dj.hr www.rtv-horvat-dj.hr Samsung Electronics...
Page 16
7. Do not attempt to connect or disconnect any wires while the TV is turned on. Make sure that the power cord is disconnected before replacing any parts. 8. To protect against shock hazard, use an isola- tion transformer. www.rtv-horvat-dj.hr www.rtv-horvat-dj.hr Samsung Electronics...
Page 17
STANDARD picture. 4. Adjust the Screen VR (on the FBT) so that the voltage on the oscilloscope becomes 120+2.5V (See Fig. 4-1). 120 2.5V 14" :120 2.5V 20, 21" : 120 2.5V Fig. 4-1 www.rtv-horvat-dj.hr www.rtv-horvat-dj.hr Samsung Electronics...
Page 18
2. Adjust RG,BG so that the levels are suitable to each local area. (c) High-Light Adjustment 1. Set SCT to 55 FL (20”. 21”), 65 FL(14”) in the Factory Service Mode with using CA100. See Fig. 4-4 www.rtv-horvat-dj.hr www.rtv-horvat-dj.hr Samsung Electronics...
Page 19
8. Since the 4-pole magnets and 6-pole magnets lines in the center area of the screen. interact, the dot movement is complex (Fig. 4-5). RED/BLUE GREEN BLUE BLUE RED/BLUE GREEN 6-Pole Magnet Movement 4-Pole Magnet Movement Fig. 4-5 Center Convergence Adjustment www.rtv-horvat-dj.hr www.rtv-horvat-dj.hr Samsung Electronics...
Page 20
Fig. 4-7 4. Adjust with VS (Vertical shift) so that the top margin of the picture is 4. Fig. 4-8 5. Adjust with HS (Horizontal Shift) so that the lion-head pattern and CRT centers are aligned. www.rtv-horvat-dj.hr www.rtv-horvat-dj.hr Samsung Electronics...
Check/Replace Voltage of Each Pin TU01S of TU01S Check IC201S Check/Replace Pins 2,3 IC201S See "No Sound" (Video OK) Check IC201S Check/Replace Pins 40,49,50 IC501, IC201S See "No Sound" See "No Video" (Video OK) (Sound OK) www.rtv-horvat-dj.hr www.rtv-horvat-dj.hr Samsung Electronics...
Block Diagram 8. Block Diagram 8-1 KS1A T U NE R -F /S SI F SA W V E R T IC AL T A E L -G 2 5 3 D K9260M A M P S/ W V I F SA W G3956M L A7840 U4468B...
SOUND L IN SOUND R OUT SOUND R IN CN603 FRONT AUDIO IN R + OUT R - OUT 21 PIN AUDIO IN L + OUT L - OUT 21 PIN VIDEO IN FRONT VIDEO IN www.rtv-horvat-dj.hr www.rtv-horvat-dj.hr Samsung Electronics...