Sealey SA76 Instructions

PARTS LIST FOR:
SPOT WELD DRILL
Issue: 1
Date: 240702
Item Part No. Description
1 SA76.01 Motor housing
2 SA76.02 Pin
3 SA76.03 Air inlet bush
4 SA76.04 Thrigger
5 SA76.05 Valve Stem
6 SA76.06 Valve bush
7 SA76.07 O-Ring
8 SA76.08 Spring
9 SA76.09 O-Ring
10 SA76.10 Muffler diffuser
11 SA76.11 Bearing cap
13 SA76.13 Ball bearing
14 SA76.14 Rear Plate
15 SA76.15 Rotor
16 SA76.16 Rotor Blade
17 SA76.17 Pin
18 SA76.18 Cylinder
19 SA76.19 Front End Plate
20 SA76.20 Ball bearing
21 SA76.21 Ball bearing
22 SA76.22 Set screw
23 SA76.23 O-Ring
24 SA76.24 Air regulator
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this equipment. WARRANTY: Guarantee is 12
months from purchase date, proof of which will be required for any claim. INFORMATION: For a copy of our latest catalogue and
promotions call us on 01284 757525 and leave your full name and address, including postcode.
Sole UK Distributor, Sealey Group, Bury St. Edmunds, Suffolk.
01284 757500
AIR OPERATED
SA76
Model:
Item Part No. Description
25 SA76.25 Planet pin
26 SA76.26 Planet cage
27 SA76.27 Planet gears
28 SA76.28 Needle bearing
29 SA76.29 Spacer
30 SA76.30 Ball bearing
31 SA76.31 Internal gear
32 SA76.32 Gear housing
33 SA76.33 Bit Holder
34 SA76.34 Set Screw
35 SA76.35 Support
36 SA76.36-6.5 Drill bit, 6.5mm
SA76.36-8 Drill bit, 8mm
37 SA76.37 Adjusting nut
38 SA76.38 Spring
39 SA76.39 Ball
40 SA76.40 Retaining ring
41 SA76.41 Wave washer
42 SA76.42 Adjustment attachment
43 SA76.43 Retainer
44 SA7644 Spring
45 SA76.45 Hex, key wrench
46 SA76.46 Hex, screw
01284 703534
E-mail: sales@sealey.co.uk
Web: www.sealey.co.uk
INSTRUCTIONS FOR:
A I R O P E R AT E D
S P O T W E L D D R I L L
Model:
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
F WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to
when using this equipment.
F WARNING! Disconnect from air supply before changing drill bits, servicing ,or performing any maintenance.
Maintain the drill in good condition (use an authorised service agent).
!
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will
!
invalidate the warranty.
Use in a suitable work area. Keep area free from unrelated materials and ensure that there is adequate lighting.
!
Before each use check condition of drill bit. Sharpen if necessary. If worn or damaged replace immediately.
!
Ensure the speed rating (rpm) of the drill bit is the same as, or greater than, the speed rating of the drill.
!
Ensure there are no flammable or combustible materials near the work area.
!
F WARNING! Always wear approved eye (or face) and hand protection when operating the drill.
Use face, dust, or respiratory protection in accordance with COSHH regulations.
!
Depending on the task, the drilling noise level may exceed 84dB in which case wear safety ear defenders.
!
Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain and/or tie back long hair.
!
Wear appropriate protective clothing and keep hands and body clear of working parts.
!
Maintain correct balance and footing. Do not over reach, ensure the floor is not slippery, wear non-slip shoes.
!
Keep children and unauthorised persons away from the working area.
!
Check moving parts alignment on a regular basis.
!
Ensure workpiece is secure before operating the drill. Never hold a workpiece by hand.
!
Check the workpiece to ensure there are no protruding screws, bolts, nuts etc.
!
Avoid unintentional starting.
!
Remove hexagonal key wrench before starting the drill.
!
F WARNING! Ensure correct air pressure is maintained and not exceeded. Recommended pressure 70-90psi
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure
!
that all connections are secure.
Prolonged exposure to vibration from this drill poses a health risk. It is the owner’s responsibility to correctly
!
assess the potential hazard and issue guidelines for safe periods of use and offer suitable protective equipment.
When not in use disconnect from air supply and store in a safe, dry, childproof location.
!
DO NOT use the drill for a task it is not designed to perform.
%
DO NOT operate drill if any parts are damaged or missing as this
%
may cause failure and/or personal injury.
F WARNING! DO NOT drill any materials containing asbestos.
DO NOT carry the drill with your finger on the trigger.
%
DO NOT direct air from the air line at yourself or others.
%
DO NOT carry the drill by the hose, or yank the hose from the air supply.
%
DO NOT force, or apply heavy pressure to the drill; let the tool do the work.
%
DO NOT place air line attachments close to your face and do not point at other
%
people or animals.
DO NOT operate drill when you are tired, under the influence of alcohol, drugs or
%
intoxicating medication.
DO NOT use drill where there are flammable liquids, solids or gases such as paint solvents and including
%
waste wiping or cleaning rags etc.
SA76
SA76 - 1 -240702