Page 2
SCHNEIDER ELECTRONICS GMBH-GERMANY 1. CAUTION CA UTION: Use of controls, adjustments or procedures other than those specified herein may result in hazardous radiation exposure. CA UT ION : T O RE DUCE TH E RIS K OF CA U T ION ELECTR ICA L SHOCK, DO NOT RE MOVE COVER (OR BACK).
Page 3
SCHNEIDER ELECTRONICS GMBH-GERMANY IMPORTANT SAFETY INSTRUCTIONS CAUTION: Read all of these instructions. Sa ve these instructions for later use . Follo w all W arnings and Instructions marked on the audio equipment. 1. Read Instructions-All the safety and operating instructionsshouldbe read before the productis operated. 2.
Page 4
SCHNEIDER ELECTRONICS GMBH-GERMANY PROTECTION AND LOCATION OF YOUR SET Do not use this television set near water ... for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc. Never expose the set to rain or water. If the set has been exposed to rain or water, unplug the set from the wall outlet and refer servicing to qualified service personnel.
Page 5
SCHNEIDER ELECTRONICS GMBH-GERMANY OPERATION OF YOUR SET 18. This television set should be operated only from the type of power source indicated on the marking label.If you are not sure of the type of power supply at your home, consult your television dealer or local power company. For television sets designed to operate from battery power, refer to the operating instructions.
Page 6
Factory Test & Alignment Specification For MS63F-LA Series (V0.10) TCL World-Wide R&D FPD CENTER Factory Test & Alignment Specification (FTAS) for MS63F-LA Series Version 0.10 Jianwei Li PREPARED BY : DATE : 2012-09-12 APPROVED BY : _____ DATE : Page 1 of 18...
Factory Test & Alignment Specification For MS63F-LA Series (V0.10) Disclosure The information contained in this document is proprietary to TCL SZ FPD lab and shall not be disclosed by the recipient to third persons without the written permission of the team leader or GM of R&D.
Page 8
Factory Test & Alignment Specification For MS63F-LA Series (V0.10) These chassis are designed for Latin America(LA) markets Ready for IPTV. The main chip is from Mstar and supports below features matrix: Class Item MS63F-LA CABLE&ANTENNA ( PAL M/PAN N/ NTSC) ANTENNA (ISDB-T) HDMI...
Page 9
±5% U208 1.2V DEMO_1V2 ±5% U209 3.3V TU_3V3 Here enclosed circuit diagram: SW Image download 1.2. Download the latest release SW from below FTP server: - Link: http://sw.tcl-cctv.com - Username: TCL_HW_MS6328 - Password: to be requested! Page 4 of 18...
RCU “Zoom±” keys to suitable ID (Project name is dynamically refreshed). See Appendix “How to change Project ID with RCU” Here below is none exhaustive ProjectID table for reference: MODEL ProjectID Panel Name L32E5300 L46E5300F L42E5300F L42D4330F3D L39E5300F/CMI L39E5300F/AUO… 006…...
Page 11
Factory Test & Alignment Specification For MS63F-LA Series (V0.10) (VGA&AUDIO) generator Half Color & Gray bars CMP via mini jack adaptor Chroma/QuantumData 1920x1080i@60Hz (YPrPb & Audio) generator Half Color & Gray bars with beyond HDMI 1.3 HDMI 2D - Movie 1280x720i@60Hz and HDCP compliant (Video &...
Factory Test & Alignment Specification For MS63F-LA Series (V0.10) memory for internal client encryption. Here are below codes examples: Device ID User ID BE4F255BBD106BC8F806AE456350D91F 3546187 Those DID/UID codes can only be set using UART commands following enclosed SIACP requirements (rev. v3.9). SIACP v3.9 (EN_20110613).pdf See Appendix...
See Appendix “Factory Menu Description” 2.2. Warm-up Test Following TCL standard and practices, it’s required minimum 15min of Warm-Up that can be considered as Burn-In. Additional Aging for White Balance alignment is no more necessary due to consistent Picture Performance with Cloning usage.
Page 14
(ex: Minolta CA210 or CA310). The analyzer may not touch the screen surface, and measurement must be performed in a dark environment keeping the probe(s) at 90+/-2° from the panel center. The result should fulfill TCL matching specification (Minolta CA310 reference with CH00): MODEL COOL(x/y)
Page 15
Factory Test & Alignment Specification For MS63F-LA Series (V0.10) 2.4. SHOP-END Test At final process stage, it’s necessary to perform “Reset shop” before any packing to leave Factory mode and restore User default presets. This function is accessible by selecting “Factory menu SHOP init”, then pressing RCU “OK”...
Page 16
Factory Test & Alignment Specification For MS63F-LA Series (V0.10) Next,click on “Auto” menu,then click “Run”,it begin programming “Mboot.bin”,when programming success,it will display a word “Pass”. Page 11 of 18...
Page 17
Factory Test & Alignment Specification For MS63F-LA Series (V0.10) Appendix “How to upgrade FLASH SW using USB” There are two methods to upgrade SW using USB,the first one like below In the previous of upgrade SW using USB,should program mboot bin file” V8-6328L01-LF1Rxxx ”...
Page 18
Factory Test & Alignment Specification For MS63F-LA Series (V0.10) 2-Warm-Up Mode submenu Item Sub-item Value Note Select panel On with left/right key, Press Warm-UP “EXIT” key to enter the burning mode; Off/On Mode Press “Menu” key on keyboard to exit the burning mode 3-ADC submenu As SoC as built-in A/D self-calibration mechanism, there’s not any ADC to perform.
Page 19
Factory Test & Alignment Specification For MS63F-LA Series (V0.10) 7-Preset Factory Channel submenu Item Sub-item Value Note Preset the channel table of factory.To preset the channel table of certain Preset Factory HZ/CD/NM/W factory,firstly,choose the corresponding X/POLAND Channel factory name,then press OK button of remote control wait...
Page 20
Factory Test & Alignment Specification For MS63F-LA Series (V0.10) Appendix “ ” 1,use the Uart command to sent DID and MAC using the command : DID write: B2 DATA 0 TO DATA N(ASCII ) UID write:B8 DATA 0 TO DATA N(ASCII ) MAC write:B3 MAC address 6 Binary The process is as the picture below:...
Factory Test & Alignment Specification For MS63F-LA Series (V0.10) Appendix ”NETWORK CONNECTION AND TEST” 1.Network connection You can set up your TV so that it can access the Internet through your local area network (LAN) using a wired or wireless connection. 1.1Connecting to a wired network You can attach your TV to your LAN using cable in three ways: •...
Page 22
Factory Test & Alignment Specification For MS63F-LA Series (V0.10) Options > Network > Configuration > Internet connection. Press • /• to select On. Wait until the connection is automatically established. 2. Select Options > Network > Configuration >Connection test, then press OK/• to check the Internet connectivity.
Page 23
Factory Test & Alignment Specification For MS63F-LA Series (V0.10) 2. Press OK to display the homepage of your browser. 3. Use • /• /• /• on the remote control to navigate through the webpage, and press OK on the remote control to confirm an entry or selection. You can also press Menu on the remote control to access or exit virtual keyboard.
Trouble shooting Can not switch on no switch on Check 3.3V/12V/24V of power supply Check PW Only 3.3V Check signal P—ON Check DC-DC DIMBL—ON of main IC link part,check to PW Check the peripheral circuit of mail IC,check solder of Check reset Check IIC bus main IC,check data fo NVM...
Page 36
2 abnormal picture Abnormal picture Individual signal source All signal source bad Check the path with this Check panel ID signal source Check LVDS signal to main Check the peripheral circuit IC check LVDS cable? of mail IC,updating SW,reset NVM,replace main IC Check crystal frequence...
Page 37
Abnormal sound Abnormal sound Individual sound Check all sound signal source source Check the sound signal Check sound IC link to main IC Check the power of Check the peripheral Check wave filter and sound IC circuit of main IC,SW speaker Check the mute function...
Page 38
H4-40F35N4-AGSA0AA L40F3520F/MS63F-LA/LVF400NE2L SJ9W00 V10 parent child description BOM text H4-40F35N4-AGSA0AA 63-W3012T-BF5G SCREW-ST 3MM 12MM ISO 19 R=Y H4-40F35N4-AGSA0AA 64-B30060-104G M/C SCREW B 3 X 6 H4-40F35N4-AGSA0AA 64-B30060-104G M/C SCREW B 3 X 6 H4-40F35N4-AGSA0AA 64-B30060-104G M/C SCREW B 3 X 6 H4-40F35N4-AGSA0AA 64-B30060-104G M/C SCREW B 3 X 6...
Need help?
Do you have a question about the L32E5300 and is the answer not in the manual?
Questions and answers