Sealey SJBEX200A Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMP P OR R TA TANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
TH H E P P RO O DUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PE E RS S ON N AL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. SAFETY
 Familiarise yourself with the applications, limitations and hazards of the jacking beam.
 Maintain the jacking beam in good condition (use an authorised service agent).
 Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the
warranty.
 Inspect the jacking beam before each use.
 DO NOT use the jacking beam if it is damaged, altered, modifi ed, in poor condition, leaking hydraulic fl uid, or unstable due to
missing components.
 DO NOT alter or modify the jacking beam in any way.
 DO NOT load the jacking beam beyond it's rated capacity.
 DO NOT allow untrained persons to operate the jacking beam.
DO NOT use the jacking beam for purposes other than that for which it is intended.

 DO NOT use the centre saddle if the work to be performed can cause the load to move.
 DO NOT operate the jacking beam when you are tired or under the infl uence of alcohol, drugs or intoxicating medication.
 Remove ill fi tting clothing. Remove ties, watches, rings, other loose jewellery and contain long hair.
 Maintain correct balance and footing. Ensure the fl oor is not slippery and wear non-slip shoes.
 Consult the vehicle manufacturer for the correct lifting locations.
 Ensure the vehicle is in PARK (automatics) and the handbrake is on before attempting to raise the vehicle.
 Only use the saddles provided with the jacking beam.
 Ensure the set-up is stable and secure before lifting. Be aware of pinch points.
 This is a lifting device only.
 Ensure the load is central on saddles before lifting.
 The jacking beam can only be used to lift one end of the vehicle.
 Ensure that there are no persons or obstructions beneath the vehicle before lowering.
Always lower the load slowly and carefully.

 WARNING! Ensure correct air pressure is maintained and not exceeded. Recommended pressure 90-145psi.
 DO NOT pull the hose from the air supply.
 DO NOT direct air from the air hose at yourself or others.
 Disconnect the jacking beam from the air supply prior to removing jacking beam from the ramp or pit and store in a safe, dry
childproof location.
 WARNING! Place the vehicle on axle stands prior to commencing any operations.
 WARNING! The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible
conditions and situations that may occur. It must be understood that common sense and caution are factors
which cannot be built into this product, but must be applied by the operator.
2. INTRODUCTION
Jacking beam lifts load with compressed air. Fully certifi ed and approved to comply with MOT requirements. Features 2-stage mechanical
safety lock and telescopic fi nger guards to prevent accidental injury. Supplied with two pairs of aluminium support blocks. Beam has
spring loaded fl at arms with roller bearings - when unloaded, these support the weight of the beam, allowing the entire unit to run smoothly
along the pit or ramp, but when loaded, they fi rmly stabilise the unit. Optional hook arms supplied. Wide lift confi guration meets MOT
recommendation for lifting on jacking point.
3. SPECIFICATION
Model No: ...........................................................SJBEX200A
Air pressure: .......................................................... 90-145psi
Beam lift: ............................................................... 95-300mm
Capacity: ..................................................................... 2tonne
Load arm reach: ................................................ 850-1600mm
Support arm reach: ........................................... 780-1075mm
© Jack Sealey Limited
2TONNE AIR JACKING BEAM WITH 1.6M
EXTENDING ARMS & FLAT ROLLER
SUPPORTS
MODEL NO:
Wear protective Wear safety
gloves footwear
Original Language Version
SJBEX200A
Wear protective
clothing
SJBEX200A Issue 1 05/10/21