Page 1
NT033 Package Included: 1 x Scanner; 1 x USB Cable; 1 x USB Dongle; 1 x Retractable Clip; 1 x Clip; 1 x Quick Setup Guide; For a complete user guide: https://www.netum.net/pages/barcode-scanner-user-manuals...
Connect Scanner with your host through USB cable (provided by Netum) or Charge the scanner take a DC plug and charge it on an electrical wall outlet. · Red Light - Charging · Green Light - Fully charged · Improtant Notes: DC Plug:V: 5V; A>500mA Low battery warning - 2 beeps, LED in red �lashing twice...
Scanner will power off after you scanning Factory Restore. Factory Restore %#IFSN0$B Netum barcode scanners are factory programmed for the most common Barcode Programming terminal and communication settings. If you need to change these settings, programming is accomplished by scanning the bar codes in this guide. An asterisk (*) next to an option indicates the default setting.
Page 6
1) Plug USB dongle into your computer. USB Wireless Connection 2) Setup keyboard language. For example if you use French keyboard, just scan “French keyboard” from keyboard language setcion in page 9. 3) Locate cursor on the place where you want scanner to output the characters then you can start to scan.
• NO software installation needed Basic Mode (HID) * • Connects to most devices • Scanner interacts with host device like a keyboard AT+MODE=2 • For iOS Devices Applicatin Mode (Apple Speci�ic Serial Pro�ile) • If you have an iOS application that supports our Scanners this is the mode to use.
Page 8
By scanning the appropriate barcode will change bluetooth transmit speed. Transmission Speed Via Bluetooth Connection AT+HIDDLY=10 AT+HIDDLY=4 *Medium Speed High Speed AT+HIDDLY=25 Low Speed POP OUT IOS Keyboard IOS Keyboard will be disabled when pairing scanner to IOS device. By pressing scanning button in the middle for 4 seconds then release it, will pop out the IOS keyboard.
Scan Mode: This mode enables the scanner to scan/capture, decode and transmit over Continue Scan Mode and over again. By clicking scan button in the middle will turn off/on the continuous scan Mode. continuous Scan Mode Scanning this bar code will enable the scanner to enter manual trigger Trigger Mode mode.
Page 10
For example If you use French Keyboard, scan command barcode of “French Keyboard Language keyboard ”. US keyboard was setup by default. $LAN#EN $LAN#FR *America EN keyboard French keyboard $LAN#GE $LAN#IT Germany keyboard Italy keyboard $LAN#PT $LAN#ES Portugal keyboard Spain keyboard $LAN#UK $LAN#HU UK keyboard...
Page 11
$LAN#TK $LAN#TF Turkey Q keyboard Turkey F keyboard Working Mode If you are heading for a working area which lies outside the Bluetooth signal range, you may activate scanner’s store mode, following step described below. Under this mode, all scanned data will be stored directly into buffer memory of the device.
Time period set for scanner from idle to sleep. Idle Time $RF#ST00 0 Min-No Sleeping $RF#ST20 $RF#ST60 10Mins 30Mins Convert Case * Disable Convert Case Up Low Case Swap (A<->a) All Upper Case (a->A) All Lower Case (A->a) (12)
Beep Volume By scanning the appropriate barcode below will change the beep volume. $BUZZ#1 $BUZZ# *High Volume Low Volume $BUZZ#0 Mute Function Key Mapping When Function Key Mapping is enabled, function characters are sent over the keypad. $KEY#MO $KEY#M1 *Disable Function Key Mapping Enable Function Key Mapping (13)
Page 14
Store Mode Green LED Flashing Downloads This is a general quick setup guide applying for Model E800, E830 , E740, E850 and E990 etc. Full manual for above models are available to be downloaded from our of�icial website. website:www.netum.net (14)
Page 15
You need to activate a speci�ic barcode type to get it to work. Please contact us for help or you may go to our of�icial website ”www.netum.net” to download the manual and then refer to the section of “Symbologies”.
Please do not hesitate to contact us if you need any other con�igurations. Tel.: +0086 20-3222-8813 Contact Information Whatsapp: +86 188 2626 1132 Email: service@netum.net Addr.:Room 301, 6th Floor and full 3rd Floor, Building 1, No. 51 Xiangshan Avenue, Ningxi Street, Zengcheng District, Guangzhou City, Guangdong Province, China...