Sealey CP4003 Instructions

thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS, AND
CAUTIONS. USE THIS PRODUCT CORRECTLY, AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY
CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INvALIDATE THE WARRANTY.
1. SAFETY INSTRUCTIONS
1.1 GENERAL SAFETY.

Disconnect the battery from the die grinder unit before changing
accessories, servicing or performing any maintenance.

Maintain the die grinder and battery in good condition. Check
moving parts alignment on a regular basis.

Replace or repair damaged parts. Use an authorised service
agent and recommended parts only. Unauthorised parts may
be dangerous and will invalidate the warranty.

Ensure the die grinder is switched off before installing the
battery.

Keep the die grinder, battery and charger clean for best and
safest performance.

Remove ill fitting clothing. Remove ties, watches, rings and
other loose jewellery and contain long hair.

Evaluate your working area before using the die grinder e.g.
ceiling, floors and enclosures may contain electrical items or
water piping.

Ensure battery is correctly inserted into the die grinder handle
and latched in place before attempting to switch on die grinder.

Secure loose workpieces with a clamp, vice or other adequate
holding device.

Avoid unintentional starting.

Wear approved safety eye protection (standard spectacles are
not adequate).

Maintain correct balance and footing. Ensure the floor is not
slippery and wear non-skid shoes.

Be aware that this die grinder does not need to be plugged into
the mains power.

Keep children and unauthorised persons away from the
working area.

DO NOT use the die grinder where there are flammable liquids,
solids or gases, such as paint solvents, etc.

DO NOT allow children to operate the die grinder.

DO NOT operate the die grinder if any parts are missing as this
may cause failure or possible personal injury.

DO NOT hold unsecured workpiece in your hand.

DO NOT carry the die grinder with your finger on the power
switch.

DO NOT use the die grinder for a task it is not designed to
perform.

DO NOT operate the die grinder when you are tired or under
the influence of alcohol, drugs or intoxicating medication.

DO NOT get the die grinder, battery or charger wet or use in
damp or wet locations.

Keep die grinder, battery and charger in a safe, dry, childproof
area where the temperature will not exceed 104°F (40°C).
1.2 ELECTRICAL SAFETY.
REGARDING DIRECT MAINS POWER USE WITH THE
CHARGING BASE AND PLUG ONLY.

WARNING! It is the owner's responsibility to read, understand
and comply with the following electrical instructions:
You must ensure the risk of electric shock is minimised by the
installation of appropriate safety devices. An RCCB (Residual
Current Circuit Breaker) should be incorporated in the main
distribution board. We also recommend that an RCD (Residual
Current Device) is used with all electrical products, particularly
portable equipment which is plugged into an electrical supply
not protected by an RCCB.You must also read and understand
the following instructions concerning electrical safety.
•
The Electricity At Work Act 1989 requires all portable
electrical appliances, if used on business premises, to be
tested by a qualified electrician, using a Portable
Appliance Tester (PAT), at least once a year.
•
The Health & Safety at Work Act 1974 makes owners of
electrical appliances responsible for the safe condition of the
appliance, and the safety of the appliance operator. If in any
doubt about electrical safety, contact a qualified electrician
•
Battery Charger Safety Instructions

WARNING! DO NOT use the charging base to charge any
battery other than that required for the tool. Other types of
batteries may explode!

Inspect the plug, cable and the charging base for wear
and damage to ensure items are safe before connecting to the
mains power supply. If worn or damaged DO NOT use,
immediately replace, or contact a qualified electrician.

Check cables are always protected against short circuit and
overload.

Uncoil the power cable between the plug and the charging base
before use.

DO NOT pull or carry the charging base by the charger power
lead, or pull the plug from the mains socket by the power lead.

DO NOT use any other type of transformer with the charging
base.

DO NOT try to open or dis-assemble the plug or charging base.

DO NOT use the plug to power any other electrical item.

Disconnect the plug from the charging base and the mains
power supply when not in use.

DO NOT expose the charging base to damp or wet conditions
(for indoor use only).

DO NOT pull or carry the charging base by the power lead.

DO NOT operate the charging base if it has been dropped, or
has received a sharp knock, or is damaged. Contact an
authorised service agent.

DO NOT dismantle the charging base as this may cause
damage or personal injury and will invalidate your warranty.

DO NOT insert foreign objects or material into the hole
reserved for the battery.

DO NOT immediately charge a second battery. Consecutive
charging will overheat the charging base. Allow the unit to cool
for 15 minutes before charging the next battery.

Ensure that the insulation on all cables and on the appliance is
safe before connecting it to the
power supply.

Ensure that cables are always
protected against short circuit
and overload.

DO NOT use worn or damaged
cables, plugs or connectors.
Immediately have any faulty
item repaired or replaced by a
qualified electrician. When a
BS1363/A UK 3 pin plug is
damaged, cut the cable just
above the plug and dispose of the plug safely.
Fit a new plug according to the following instructions (UK only).
a) Connect the GREEN/YELLOW earth wire to the earth
terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
d) After wiring, check that there are no bare wires, that all
Original Language Version
INStRUCtIONS FOR:
CORDLESS LITHIUM-ION
DIE GRINDER 12v
CP4003
MODEL No:
Yellow & Green
Earth Wire
Blue
Neutral
Wire
CP4003
Cable
Restraint
FUSE RATING
5 AMP
Issue: 2 - 01/03/10