Samsung BN68-02662A-01 Quick Setup Manual

Quick Setup Guide

Congratulations on the purchase of your new Samsung TV.
Read this setup guide to get your TV up and running quickly.
1-800-SAMSUNG (1-800-726-7864)
STOP
Samsung Electronics America, Inc.
85 Challenger Road Ridgefield Park, NJ 07660-2112
Please do not return this unit.
Samsung Electronics Canada Inc.
55 Standish Court Mississauga, Ontario L5R 4B2
If you have problems operating your
Call Center hours of operation: Mon-Sun, 9:00 AM -12
TV, call:
AM EST.
1-800-SAMSUNG (1-800-726-7864)
To register this product, visit: www.samsung.com/
For web support please visit:
register.
www.samsung.com/support
Step 1
: Install the Stand
Follow the steps below to connect the TV to the stand.
✎
NOTE
x
Make sure to distinguish between the front and back of the Stand and
Guide Stand when assembling them.
x
Make sure that at least two people lift and move the LED TV.
x
Stand the product up fasten the screws. If you fasten the screws with the
with the LED tv placed down, it may lean to one side.
[
Do not insert your fingers into the stand base slot of the TV when
installing the stand base.
Screws (M4 X L12)
1
Guide Stand
Connect the Guide Stand to the
Stand
Stand using four screws
(M4 X L12) as shown.
Rear
3
2
Fasten two screws (M4 X L8) at
With your TV upright, connect the position 1, and then fasten three
TV to the Stand as shown. screws (M4 X L8) at position 2.
2
Front
1
Rear
Step 2
: Install the Batteries into the Remote
To install batteries into your remote
control, follow these steps:
1. Lift the cover on the back of
the remote upward as shown
in the figure to the right.
2. Install two AAA batteries.
✎
Make sure to match the
+ and - ends of the batteries to the diagram in the battery compartment.
3. Replace the cover.
Step 3
: Connect Antenna or Cable
VHF/UHF Antenna
Connect Ant In to
Antenna Cable
• Wall cable jack
• VHF/UHF Antenna
or
• Cable or Satellite box
Ant or Cable Out
Use a 75 ohm (round) cable.
Make sure the AC power cord is plugged in securely to
the wall outlet and the TV.
Step 4
: Connect External Devices
Connecting an AV device (DVD/Blu-ray player, cable/satellite box, etc.)
Use one of the connections below to connect your TV to an external A/V device. We recommend using HDMI for the highest picture quality.
Audio Cable
(Not Supplied)
Video Cable
(Not Supplied)
Top view
Good Connection
Component Cable
Component connection (up to 1080p)
(Not Supplied)
Audio Cable
(Not Supplied)
COMPONENT OUT
AUDIO OUT
Connecting an audio device (Home Theater, etc.)
Connect your TV to your Home Theater or other audio device to enjoy enhanced
Sound quality.
Analog Audio connection
Using an Audio Cable
Audio Cable (Not Supplied)
AUDIO IN
Digital Audio connection
Using an Optical Cable
Optical Cable (Not Supplied)
OPTICAL
Best Connection
HDMI Cable (Not Supplied)
Very Good Connection
Component connection (up to 1080p)
HDMI to DVI Cable (Not Supplied)
DVI OUT
Audio Cable (Not Supplied)
AUDIO OUT
Lowest Quality Connection
Audio/Video connection (480i only)
Using a Component Cable
DVD, Blu-ray player, cable box,
STB satellite receiver, VCR
AUDIO OUT VIDEO OUT
Device
VIDEO OUT
Connecting a PC
Connect your TV to a PC to use it as a Monitor.
Optical Cable (Not Supplied)
Amplifier / DVD
home theater
Audio Cable
(Not Supplied)
D-Sub Cable
Digital Audio System
(Not Supplied)
Using an EX-Link Cable Connection
Available Devices : External devices that support EX-Link
EX-LINK
Step 5
: Run Plug & Play
When you turn on your TV for the first time, it automatically launches the Plug &
Play function. With Plug & Play, you can select the On Screen Display language,
set the clock mode, and launch the TV's channel memorizing process.
It also displays connection instructions similar to those in this guide.
To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow
buttons on your remote. To make a selection, press the ENTERE button.
To skip a screen, press the
HD connection (up to 1080p)
button on the remote or on the TV. To run Plug & Play, follow these steps:
1
Using an HDMI Cable
Using your remote control, select
DVD, Blu-ray player, HD Cable Box, HD
the language for the On Screen
STB (Set-Top-Box) satellite receiver
Display (OSD), and then press the
Device
HDMI OUT ENTERE button.
2
Select Home Use, and then
press the ENTERE button. If
you select Store Demo, the TV
will reset your picture and audio
Using an HDMI to DVI Cable settings every 30 minutes.
3
Select Antenna Source to
Device
memorize. If Antenna Source is
Cable or Auto, you must select
Antenna Source to same type
as your cable system type. After
selecting source, select Search;
then press the ENTERE button
on your remote.
✎
Most cable systems are
Standard(STD) systems, If you are
Using an Audio/Video Cable
not sure about what kind of cable
DVD, Blu-ray player, cable box, system you have, contact your cable company.
STB satellite receiver, VCR
✎
If your TV is attached to a cable or satellite box, skip Steps 3 through 5. After
Plug & Play is complete, set your TV to Channel 3 or 4, according to the
Device
directions for your cable or satellite box.
4
The TV memorizes the available
channels. This process can take
up to 45 minutes.
5
After the TV has memorized the
channels, choose the Clock
HD connection
Mode. Select Auto if you have
a digital channel in your area.
Using an HDMI to DVI Cable
Select Manual if you don't, or if
DVI OUT
you have a cable or satellite box.
When done, press the ENTERE
AUDIO OUT button.
✎
If you select Manual, the clock
setting screen appears.
Audio Cable (Not Supplied)
6
Select the daylight savings time
setting: Off or On, and then press
the ENTERE button.
Using an D-Sub Cable
7
AUDIO OUT
Select the time zone in which
you live, and then press the
PC OUT
ENTERE button.
8
After the time zone screen, The connection method for best HD screen
quality is displayed. Press Right arrow button on your remote to view each
screen in succession. Press the Blue button to skip this section.
9
The Enjoy your TV. screen appears. Then press the ENTERE button.
If You Want to Rerun Plug & Play
1. Press the SOURCE
: Connector for service only.
2. Press the MENU
3. Press the ▲ or ▼ button to select Setup, and then press ENTERE.
4. Press ENTERE again to select Plug & Play.
MENU button. To turn on your TV, press the POWER
Plug & Play
Select Language of the OSD.
English
Español
Menu Language :
Français
U Move E Enter
Plug & Play
Select the usage mode.
Store Demo Home Use
Previous U Move E Enter
Plug & Play
Anrenna Source :
Air
Digital Cable System :
Cable
Auto
Analog Cable System :
Search
U Move E Enter
Plug & Play
Removing scrambled channel.
DTV Cable 14
76%
DTV Air 0 Air 12
212
DTV Cable Cable 52
Stop
E Enter
Plug & Play
Set the Clock Mode.
Auto
Clock Mode :
Manual
U Move E Enter
Plug & Play
Set to daylight saving time.
Off
DST :
On
U Move E Enter
button on your remote, then select TV mode.
button on your remote to display the menu.