Sim2 XTV 4K INV Quick User Manual

Hide thumbs Also See for XTV 4K INV:

Advertisement

Quick Links

SIM2 XTV 4K INV
Installation
Quick User Guide
(EN/1.2)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the XTV 4K INV and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Sim2 XTV 4K INV

  • Page 1 SIM2 XTV 4K INV Installation Quick User Guide (EN/1.2)
  • Page 3 Contents 1 Important information About this User Guide Safety Usage Notice 2 Product overview and dimensions 3 Recommendations Installing SIM2 XTV 4K INV 4 Installation Location Mounting Framing requirements for furniture Adjusting the image Fine adjustment knobs Cooling basic regulations 5 Appendices Regulation &...
  • Page 4 Except where otherwise indicated, the information in this guide applies to all the projectors listed above, that will be referred to as “SIM2 XTV 4K INV”. Information contained in this User Guide may be updated from time to time due to product improvements and customer feedback.
  • Page 5 14. The unit should only be installed and repaired only by appropriate service personnel. Adequate instructions for assembly, operation and maintenance, including clear warnings concerning precautions to avoid possible exposure to laser and collateral radiation in excess of the accessible emission limits in Class 2. SIM2 XTV 4K INV Installation: Quick User Guide...
  • Page 6: Usage Notice

    • Use abrasive cleaners, waxes or solvents to clean the unit. • Use under the following conditions: - In areas susceptible to excessive dust and dirt. - Near any appliance generating a strong magnetic field. - In direct sunlight. SIM2 XTV 4K INV Installation: Quick User Guide...
  • Page 7 Top View Removable crystal glass Cabinet Fixing removable glass Projecting area Eyes protection IR receiver Ambient brightness sensor Led status For more detailed information, please refer to your local SIM2 office or representative. SIM2 XTV 4K INV Installation: Quick User Guide...
  • Page 8 SIM2 XTV 4K INV Installation: Quick User Guide...
  • Page 9 The installation distance between the SIM2 XTV 4K INV and the projection surface depending on the required projection size. For details on the distance between the SIM2 XTV 4K INV rear glass surface, the projection surface and the size of projected image see the “Projection Distance table” below.
  • Page 10 - In the case of installations where absolute alignment precision is required, reference must be made to the projection measurement sheet which forms an integral part of the documentation of each product. SIM2 XTV 4K INV Installation: Quick User Guide...
  • Page 11 For each unit, we also supply the “Univocal Measurements Sheet” (the figure below is an example): it provides the measurements in order to obtain a predefined screen size. SIM2 XTV 4K INV Installation: Quick User Guide...
  • Page 12: Installation

    Screen or projection surface must be flat. Position the SIM2 XTV 4K INV so that the rear crystal-glass is parallel to the projection surface. SIM2 XTV 4K INV...
  • Page 13 Framing requirements for furniture To make the opening in the furniture to fit the SIM2 XTV 4K INV, consider the dimensions/measurements below; one of the two included rubber gaskets (3 or 4 mm, depending on the material the furniture is made of) may be used to seal the furniture opening in order to prevent liquid spills from entering into the furniture.
  • Page 14 SIM2 XTV 4K INV Installation: Quick User Guide...
  • Page 15 To fix the unit in the furniture, it’s possible use the 4 installation brackets supplied with the unit. Fix them to the cabinet using the 5mm screws and adjust the position in order to fix the unit to the furniture. SIM2 XTV 4K INV Installation: Quick User Guide...
  • Page 16: Adjusting The Image

    To regulate the bottom adjustment knobs, make sure to leave at least 12 cm (4.8“) of free space underneath the unit. The adjustments described below are intended to adapt the SIM2 XTV 4K INV to the Customer’s installation in order to obtain the best geometry of picture.
  • Page 17 WARNING: we suggest to perform the regulation by doing small adjustments of the knobs; being SIM2 XTV 4K INV an Ultra Short Throw model, small movements of the projector cause large shifts in the picture, which are more evident in the top of the image.
  • Page 18 Here below is a list of examples of the effect that the adjustment of each knob has on the picture. Again, each regulation also influences other parts of the picture therefore, some regulations already done might require to be re-adjusted a second time. PICTURE ADJUSTMENT > > > > SIM2 XTV 4K INV Installation: Quick User Guide...
  • Page 19 > > > > SIM2 XTV 4K INV Installation: Quick User Guide...
  • Page 20 2. When using a projection surface with an uneven surface (i.e. wall), stripes may seldom appear on the surface depending on the distance between the projection surface and the SIM2 XTV 4K INV. This is not a malfunction of the SIM2 XTV 4K INV. SIM2 XTV 4K INV...
  • Page 21 Cooling basic regulations SIM2 XTV 4K INV must be placed in a forced air flow rack design or furniture. A forced air rack design uses fans or blowers to remove heat by creating pressure differences that ensure a steady flow of air through the rack enclosure.
  • Page 22: Regulation & Safety Notices

    • In case of using the unit in a dusty location or for a long time, the internal air filters can be obstructed and the projector cannot works properly; in this case contact a local Service Center for the appropriate maintenance. SIM2 XTV 4K INV Installation: Quick User Guide...
  • Page 23: Specifications

    6 Specifications Projection Type Digital Light Processing (DLP), 1-chip DLP Type: 4K, 3840 x 2160 Light source: LASER HYBRID (lifetime approx. 25.000 hours) Contrast: Adaptive Brightness: up to 2,900 Ansi lumens Audible noise: <32dB Picture size: 85” – 120” (120” should have some distortion in the image or less clear picture but still enjoyable video performances) Projection Lens: High-quality glass...
  • Page 24 SIM2 BV International S.r.l. Registered Office Via Gorizia, 10 33170 Pordenone – ITALY Offices and Service Via Udine, 59 33061 Rivignano Teor (UD) - ITALY Phone: + 39 0434 383292 Fax: +39 0434 383260 Email: info@sim2.it www.sim2.com SIM2 USA Inc.

Table of Contents